Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
2017 vehicles equipped with a 2.0L GTDI, 2.3L GTDI, or 2.5L PFI engine will either be equipped with a diamond washer on each side of a smooth-faced crankshaft timing sprocket (early build), or a crankshaft timing sprocket with laser etched faces and no diamond washers (late build). If equipped, diamond washers should be cleaned, inspected and reused, if undamaged. Diamond washers should never be installed along with a laser etched crankshaft timing sprocket. Related WSM procedure information is in the process of being updated.
Some 2016-2017 Ford/Lincoln vehicles SYNC 3 may exhibit an intermittent blank screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or blank screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Some 2016 c-max and focus electric vehicles may exhibit a false activation of the alarm system. A work around until the software is updated(4th qtr. 2016), procedure is available. 1. Put the vehicle in park. 2. Take your foot off the brake pedal and keep it off. 3. Turn the vehicle off (push button start/stop. 4.Exit vehicle and lock the doors to activate the alarm. Note: If the brake is touched after turning the key off then just turn the car on again and start this procedure again.
Some 2016 c-max and focus electric vehicles may exhibit a false activation of the alarm system. A work around until the software is updated(4th qtr. 2016), procedure is available. 1. Put the vehicle in park. 2. Take your foot off the brake pedal and keep it off. 3. Turn the vehicle off (push button start/stop. 4.Exit vehicle and lock the doors to activate the alarm. Note: If the brake is touched after turning the key off then just turn the car on again and start this procedure again.
Ford/lincoln: Due to an adherence failure of rtv sealant, there is a transmission fluid leakage, in some vehicles, from damper housing to transmission case joint. Model 2013 c-max, 2013-14 fusion, mkz. *pe
Ford/lincoln: The damper housing to transmission case joint, there is a fluid leak caused by an adherence rtv failure. 2013 c-max, 2013-2014 fusion, mkz. *pe
Ford: Within 20 seconds after remote starting vehicle, there is a start stall issue and diagnostic trouble code (dtc) p1594 is set in body control module (bcm). Model 2012-2014 focus, 2013-2014 escape, c-max. *pe
Ford/lincoln: There is a no start condition and the red triangle lamp will illuminate and the battery energy control module (becm) will need reprogramming to latest calibration due to storage of diagnostic trouble codes (dtc) p0adc, p0ae0 and/or p0ae7. Model 2013 c-max, 2013-2014 fusion, mkz. *pe
Energi - Malfunction Indicator lamp (MIL) with diagnostic trouble code (DTC) P0C27 AND/OR P0C28
Hmm, wait. The title is short and has no German-translatable prose beyond "Malfunction Indicator lamp", "diagnostic trouble code" which I should translate. Let me produce the proper translation.
**Energi – Leuchte der Motorkontrollanzeige (MIL) mit Diagnose-Fehlercode (DTC) P0C27 und/oder P0C28**
Verschiedene Fahrzeuge der Baujahre 2012 bis 2015 mit einem 3G-Modem können eine eingeschränkte Leistung des 3G-Modems aufweisen. Ursache dafür kann sein, dass der 3G-Mobilfunkdienst ab August 2021 bis einschließlich März 2022 abgeschaltet wird. Mit der Abschaltung des 3G-Mobilfunkdienstes verlieren Fahrzeuge mit dem 3G-Telematiksteuergerät (TCU) die Funktionalität und Verbindung der Apps MyFord Mobile und MyLincoln Mobile. Die Reparatur oder der Austausch des TCU darf nicht mehr mit vorhandenen Teilen aus dem Servicelager durchgeführt werden. Der Austausch des 3G-TCU wegen dieses Problems führt zu Programmierproblemen, daher sollten keine Reparaturen durchgeführt werden.
Einige Fahrzeuge von Ford und Lincoln der Baujahre 2018–2020, die mit TCU und WLAN-Hotspot ausgestattet sind, zeigen beim Versuch, das Hotspot-Menü aufzurufen, möglicherweise die Meldung „Hotspot-Funktion für dieses Fahrzeug nicht aktiviert“ an. Bei Verwendung der Anwendung FordPass/Lincoln Way erhält der Kunde unter Umständen die Meldung, dass das WLAN für dieses Fahrzeug deaktiviert wurde. Prüfen Sie die Fahrzeugspezifikationen oder die Fahrzeugbauinformationen auf den mfal-Code auf der PTS-Website (Detaillierte Fahrzeugspezifikationen). Wenn mfal = WAFAC oder WAFAB ist, tauschen Sie das TCU nicht aus, da die Technik diesen Zustand derzeit untersucht. Informieren Sie den Kunden, dass Ford an einer Softwarelösung arbeitet, die voraussichtlich Anfang März verfügbar sein wird. Teilen Sie dem Kunden bis dahin mit, dass er das Fahrzeug weiterhin fahren kann, und vereinbaren Sie mit ihm einen Folgetermin für Anfang März. Verfolgen Sie OASIS auf Aktualisierungen.
Einige Ford- und Lincoln-Fahrzeuge der Baujahre 2018–2020 mit TCU und WiFi Hotspot zeigen beim Aufrufen des Hotspot-Menüs möglicherweise die Meldung „Vehicle Hotspot feature not enabled on this vehicle“ an. Bei Verwendung der FordPass/Lincoln Way-Anwendung erhält der Kunde unter Umständen die Meldung, dass WLAN für dieses Fahrzeug deaktiviert wurde. Prüfen Sie die Fahrzeugspezifikationen oder Fahrzeugkonfigurationsdaten auf den mfal-Code. Wenn mfal = WAFAC oder WAFAB ist, tauschen Sie die TCU nicht aus, da die Entwicklung diesen Zustand derzeit untersucht. Informieren Sie den Kunden, dass Ford an einer Softwarelösung arbeitet, die für Anfang Januar erwartet wird. Teilen Sie dem Kunden in der Zwischenzeit mit, dass er das Fahrzeug weiterhin fahren kann, und vereinbaren Sie mit ihm einen Folgetermin für Anfang Januar. Sobald das Update verfügbar ist, kontaktieren Sie den Kunden und bestätigen Sie, dass der Werkstatttermin stattfindet. Überwachen Sie OASIS auf Aktualisierungen.
Einige Fahrzeuge des Modells 2017 Fusion Hybrid/Fusion Energi/MKZ Hybrid/C-Max und 2019 Fusion Hybrid/MKZ Hybrid, die am oder vor dem 27.01.2019 gebaut wurden, können eine leuchtende Motorkontrollleuchte (MIL) mit dem im Antriebsstrang-Steuermodul (PCM) gespeicherten Diagnosefehlercode (DTC) P013A aufweisen. Dies kann auf die Parameter des stromabwärts gelegenen Sauerstoffsensors in der PCM-Software zurückzuführen sein. Zur Behebung des Zustands ist die PCM-Software zu aktualisieren.
Some 2014-2015 Escape, 2015 C-Max and Focus vehicles equipped with integrated remote start may exhibit an illuminated MIL with diagnostic trouble code (DTC) P0116 in the powertrain control module (PCM) immediately following a remote start event. Vehicles may also display a warning message stating Engine Coolant Over Temperature. This condition may occur when remote start is used and the vehicle is allowed to time out (engine shuts off). Reprogram the body control module (BCM) using the latest software version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 12A648 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Some 2016 C-MAX and Focus Electric vehicles built on or after 11-May-2016 may exhibit a false activation of the alarm system. Reprogram the body control module (BCM) to the latest level using Integrated Diagnostic System (IDS) release 110.03 or higher. To correct the concern Make sure you are connected to the internet when entering module programming to obtain the latest updates. Use the applicable labor operation in section 10 of the Service Labor Time Standards manual and causal part 14A068 when claiming repair. Calibration files may also be obtained at www.motorcraftservice.com
The EV Range after fully charging a Focus Electric, C-MAX/Fusion Energi may vary after each charge event. The window sticker indicates 0-20 mile range for C-MAX Energi, 0-21 mile range for Fusion Energi. Variation of EV range may not indicate a battery or charging concern. EV range is similar to the DTE display on gasoline vehicles, EV range will vary with driving/operating conditions. Conditions include: extreme outside temperatures, terrain, driving style, city or highway driving, tire pressure, and use of accessories. If the customer replaces the low roll resistance tires with a more aggressive tread the range will suffer. Using the cabin heater and A/C, which are electric, will also decrease EV range. To temporarily remove the impact of driving/climate history , reset the Driving History/Lifetime Summary by using the Settings menu on the left side of the instrument cluster, under Display
The EV Range after fully charging a Focus Electric, C-MAX/Fusion Energi may vary after each charge event. The window sticker indicates 0-20 mile range for C-MAX Energi, 0-21 mile range for Fusion Energi. Variation of EV range may not indicate a battery or charging concern. EV range is similar to the DTE display on gasoline vehicles, EV range will vary with driving/operating conditions. Conditions include: extreme outside temperatures, terrain, driving style, city or highway driving, tire pressure, and use of accessories. If the customer replaces the low roll resistance tires with a more aggressive tread the range will suffer. Using the cabin heater and A/C, which are electric, will also decrease EV range. To temporarily remove the impact of driving/climate history , reset the Driving History/Lifetime Summary by using the Settings menu on the left side of the instrument cluster, under Display
Some 2016 Escape and Focus vehicles equipped with a front control display interface module (FCDIM) may exhibit the inability to store AM/FM presets and/or preset buttons work erratically. Engineering is currently investigating this concern. Until a new service procedure and/or parts are available use the pre-set buttons in the following manner. To store/program a new station for a pre-set location, press and hold desired button for 3 seconds. To select a previously programmed pre-set location, perform a quick press and release of the button. Refer to Workshop Manual (WSM) Section, 415-00 for normal diagnostics. Continue to monitor OASIS for updates.
Some 2017 C-MAX vehicles built 1-Jun-2017 and through 26-Sep-2017 may exhibit an illuminated MIL with DTCs P26D0, P26CA, P059F, U019F, U0194, U091F and/or U0284. This may be due to water in the jumper harness connector C1651 and the attached connector on the active grill shutter actuator. Remove connector, clean and dry, add electrical grease Motorcraft XG-12 or equivalent to the terminals. Engineering is investigating, monitor OASIS for updates.
Some 2017 Ford and Lincoln vehicles equipped with SYNC 3 and navigation may exhibit a condition in which the SiriusXM Traffic Listing is not loading but all remaining Travel Link features operate properly. SiriusXM Traffic is only available on vehicles equipped with navigation, only in select markets and requires an active subscription to SiriusXM Traffic information. If SiriusXM Traffic will not load attempt the following procedure. Turn the ignition off, open and close the drivers door, wait for 3 minutes, then drive the vehicle outside to obtain a clear view of the sky. SiriusXM Traffic should recover. If SiriusXM Traffic does not recover continue to monitor OASIS for future updates. Engineering is aware of this concern and no component replacement or any software re-flashes should be performed at this time. The SYNC version can be confirmed via OASIS.
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may have DTCs U3000:04, B108E:12 and/or U1A00:87 present in the APIM. If these DTCs are present and no other symptoms are reported by the customer, then clear the DTCs and retest. If the DTC(s) do not return then no further repairs should be attempted. If one or more DTCs return as current faults and/or the customer reports other symptoms, then refer to Workshop Manual, Section 415-00 for further diagnostics. The SYNC version can be confirmed via OASIS.
Some 2017 C-MAX/Fusion Hybrid/Energi and MKZ Hybrid vehicles may exhibit an illuminated MIL with DTC P0071 stored in the powertrain control module (PCM). This DTC can be set after the vehicle is stored inside a warm location for several hours and then driven on a cold day. Under these conditions the PCM may see a temperature sensor concern when it first compares the ambient air temperature (AAT) sensor to other engine temperature sensors and set the DTC. Reprogram the PCM to the latest calibration using Integrated Diagnostic System (IDS) release 104.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
Some 2012-13 Focus and 2013 Escape/C-MAX vehicles may have the wrong part in the box for the BCM (base 14A068). The suspect service part number is GV6Z-14A068-G. The wrong part will have an engineering number of GV6T-14A073-GD and it will not work. The correct part will have engineering part number of GV6T-14A073-with a suffix of XA, XB, XC, or XF. Dealers should utilize the normal return process of a miss packaged part. Continue to monitor OASIS. When this concern is resolved, an update will be provided.
Some vehicles may exhibit an illuminated mil with diagnostic trouble codes (dtcs) p0011, p0012, p0014, p0015, p0016, p0017, p0018, p0019, p0021, p0022, p0024 and/or p0025. This may be due to small debris causing the vct solenoid to stick. Before attempting any component diagnosis or replacement of the vct solenoid, refer to powertrain control and emissions diagnosis (pc/ed) pinpoint test hk11 to cycle the affected vct solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6m280 and applicable labor operations in section 10 of the service labor time standards (slts) manual.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).