Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
Some 2021 Edge vehicles which have received an APIM software update may experience a concern with Sirius radio being inoperative. This will be accompanied by ACM diagnostic trouble code (DTC) B1A89:13 for the satellite antenna. To correct this condition, download and run the APIM Programmable Module Installation (PMI) application using the latest software level of the Ford Diagnosis and Repair System (FDRS). When the PMI asks, Is The Original Module Installed?, select NO. When the PMI completes, perform an ALL CMDTC test and clear all DTCs. For claiming, use causal part 14G670 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Some 2021 Mustang Mach-E/F-150/Edge/Nautilus vehicles equipped with SYNC Gen 4 may experience a USB Error 0 being displayed in the infotainment screen during Programmable Module Installation (PMI) on the replacement accessory protocol interface module (APIM) ordered on 01-Jan-2022 and through 13-Apr-2022. This maybe due to a software issue with the replacement APIM. Order another APIM from Ford Component Sales (FCS). Service stock has been corrected.
Some 2021 Mustang Mach-E, F-150, and Edge vehicles may experience a GWM and/or TCU programming failure with an error message displayed in the Ford Diagnosis and Repair System (FDRS) stating The Programming Or Part Number Validation Process Has Failed. This may be due to the USB flash drive being removed from the vehicle media hub before fully completing reprogramming. Reprogram the module(s) following the vehicle onscreen prompts. After the ignition cycle during reprogramming, the touchscreen may go blank. This is a normal part of the reprogramming process. Leave the USB flash drive installed in the media hub until the touchscreen displays Update Successful.
Some 2021 Mustang Mach-E, Edge and Nautilus customers may be unable to authorize the FordPass/LincolnWay app and the Enable Connected Services prompt is not showing in the SYNC screen with no diagnostic trouble codes (DTC) present in the telematics control unit (TCU) or the gateway module A (GWM). To resolve this condition, remove the TCU fuse for 5 minutes then reinstall. If available, update the TCU to the latest software level using the latest version of FDRS and try to authorize the vehicle to the app. If the concern is still present, remove the GWM fuse for 5 minutes and reinstall. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00.
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 48558 - 2017-2020 Various Vehicles Equipped With Telematics Control Unit (TCU) - Various FordPass/LincolnWay Mobile App Concerns Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
Some 2019 Mustang, Continental, Fusion, MKZ, F150, Transit Connect, Ranger, Edge or Nautilus with SYNC 3 may have the following intermittent symptoms: a solid blue screen when moving forward at speeds above 16 kph (10 mph), the rear view camera remains on the screen at speeds below 16 kph (10 mph), or inoperative infotainment applications. This may be due to the SYNC 3 software version installed on the vehicle. To correct the condition, follow the Service Procedure steps to reprogram the accessory protocol interface module (APIM).
Some 2019 Mustang, Continental, Fusion, MKZ, F150, Transit Connect, Ranger, Edge or Nautilus with SYNC 3 may have the following intermittent symptoms: a solid blue screen when moving forward at speeds above 10 mph, the rear view camera remains on the screen at speeds below 10 mph, or inoperative infotainment applications. To resolve this concern, check for a SYNC software update under the OASIS Tab SYNC selection. If an update is available, update the APIM software per WSM section 415-00. After the complete pop-up appears, remove the USB flash drive and install it into the IDS tool to update the Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes, which is critical for a successful installation. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Some 2016-2017 Ford/Lincoln vehicles SYNC 3 may exhibit an intermittent blank screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or blank screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Some 2016-2017 ford/lincoln vehicles with sync 3 may see a navigation fault message appear on the map on the home screen or a system lock up when the phone is connected. Applink maybe inoperative, or the system may perform random reboots during an ignition cycle with the phone connected. Determine if the customer has an android phone with the baseball application mlb.Com at bat installed. If the customer does not have this application loaded then proceed to the wsm, section 415-00 for normal diagnosis. If the customer does have this application loaded verify if the version is 5.1.3 or lower on the android phone. If the android phone with mlb.Com at bat has version 5.1.3 or lower please recommend that they update their app to version 5.2 or higher and retest for the customer symptom. The sync version can be confirmed via oasis.
Some 2022 Edge vehicles built on and after 16-Nov-2022 and 2022 Explorer vehicles built on and after 20-Sep-2022 may exhibit a brief illumination of the malfunction indicator lamp (MIL) when the vehicle is shifted into park (P) with diagnostic trouble code (DTC) P0919 and/or P0929 stored in the gear shift module (GSM). This may be due to the GSM software. To correct this condition, update the software in the GSM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming use the causal part number 7P155 and applicable labor operations in Section 07 of the Service Labor Time Standards (SLTS).
Software Update 4 P1 for 2023 Model Year EDGE vehicles is now available. Quality improvements include: - Improved vehicle accessibility during OTA update. - Improved messaging if pre-conditions aren't met.
Certain 2021 Model Year Mach-E, F-150, Bronco, Edge, Nautilus vehicles Electronic Control Module Recovery REASON FOR THIS SUPPLEMENT Program Terms: The program expiration date was incorrectly shown as October 31. 2022. The correct date is April 30, 2023. Affected Vehicles: The build dates were updated. Verbiage added to indicate the population will increase as more vehicles with modules needing recovery are identified. Service Action: Verbiage added to indicate the population will increase as more vehicles with modules needing recovery are identified. Owner Notification Mailing Schedule: Verbiage added on mailing owner letters to additional owners as they are identified. Owner Refund Expiration Date: The owner refund expiration date was incorrectly shown as May 27, 2022. The correct date is April 30, 2023.
Certain 2021 Model Year Mach-E, F-150, Bronco, Edge, Nautilus vehicles Electronic Control Module Recovery: In some of the affected vehicles, an internal error in the Accessory Protocol Interface Module (APIM) or Telematics Control Unit (TCU) module software will prevent the receipt of software updates or enhancements for these modules Ford Power-Up or Lincoln Way. The module will operate as intended otherwise.
Some 2021 Edge vehicles may exhibit the front camera not turning back on if the camera system button is pressed once the vehicle is below the speed threshold of 6MPH (10km/h). This may be due to the accessory protocol interface module (APIM) software. Inform customers that engineering is currently working on a solution for this condition and will be released via an over the air (OTA) software update, expected in September 2022. Software will update automatically if the vehicle is connected to Wi-Fi. Monitor OASIS for additional information. Schedule a service appointment for customers that are not connected to Wi-Fi once the repair becomes available.
Some 2021 Edge vehicles may exhibit the front camera not turning back on if the camera system button is pressed once the vehicle is below the speed threshold of 6MPH (10km/h). This may be due to the accessory protocol interface module (APIM) software. Inform customers that engineering is currently working on a solution for this condition and will be released via an over the air (OTA) software update, expected in September 2022. Software will update automatically if the vehicle is connected to FordPass. Monitor OASIS for additional information. Schedule a service appointment for customers that are not connected to FordPass once the repair becomes available.
Certain 2021 Model Year Mach-E, F-150, Bronco, Edge, Nautilus vehicles - Electronic Control Module Recovery: In some of the affected vehicles, an internal error in the Accessory Protocol Interface Module (APIM) or Telematics Control Unit (TCM) module software will prevent the receipt of software updates or enhancements for these modules from Ford Power-Up or Lincoln Way. The module will operate as intended otherwise.
Software Update 2 (SU2) Phase 2 for 2021 Model Year Edge vehicles is now available. Involves: Fix for availability of subscription services, and an update resolve any blank screens or distorted images (22S14).
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).