Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

IsuzuIsuzu Ascender

2002–2008 · 7 dokumentierte Mängel · 1 Märkte

Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.

SchweregradAlleMittelGering
Modelljahr
MarktAlleNA
BulletinMittelKarosserieNA

Bulletin

Isuzu diesel engines available in the above affected vehicles meet the california air resource board's (carb) optional idling emissions standard of 30 grams per hour of oxides of nitrogen (nox) with no increase in the emission of other regulated pollutants. As a result these vehicles have been approved as "certified clean idle" and are "exempt" from the engine shutdown system (ess) requiremnet pursuant ot section 1956.8 of title 13, california code of regulations. As required by the ess regulation, for "certificed clean idle" vehicles, isuzu has introduced a tamper resistance "certified clean idle" label located on the driver's side door panel. It is important that this label remain, permanently, on the vehicle to identify it as "certified clean idle." carb requires this label as evidence that, at hte time of manufacture, the engine installed met the applicable emission standards. Should the label be found missing or damged during an inspection, a citation and penalties may be issued. If the vehicle is operated in california with a damaged or missing clean idle label, isuzu recommends vehicle operators follow the 5 minute ess requirement by manually turning off the engine. Following this ess requiremnet will keep the vehicle operation compliant until a replacement label can be installed. "clean air idle" labels are printed with a serial number and registered to an individual vin. As a result, a replacemnet label will also include a new serial number which must be registered to the vehicle's vin by the manufacturer. The below information is provided to assit in acquiring, replacing and registering a replacement label.

NHTSA · Herstellerbulletin10178754Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelGetriebeNA

Bulletin

This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.

NHTSA · Herstellerbulletin10112600Modelljahre 2004Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelInnenraumNA

Bulletin

Airbag light on, passenger airbag status indicator reads off, dtc b0092. *kb

NHTSA · Herstellerbulletin10022540Modelljahre 2007Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelGetriebeNA

Bulletin

4l60-e automatic transmission fluid leak from oil pump or bell housing area. *kb

NHTSA · Herstellerbulletin10020537Modelljahre 2006Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

Revised steering wheel replacement procedure (service manual revision). *tt

NHTSA · Herstellerbulletin10006663Modelljahre 2003Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelSonstigesNA

Bulletin

Intermittent hesitation, stumble or idle stall after soak, harsh 1-2 shift, slipping 1-2 shift followed by a harsh engagement. *tt

NHTSA · Herstellerbulletin10006094Modelljahre 2003Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

Revised steering wheel replacement procedure. *tt

NHTSA · Herstellerbulletin10005165Modelljahre 2003Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

Squeak noise coming from the steering column while turning the steering wheel. *tt

NHTSA · Herstellerbulletin10001769Modelljahre 2003Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringSonstigesNA

Bulletin

Policies and procedures update for all commercial vehicles. This bulletin provides instructions with regard to the Isuzu Commercial Vehicle (CV) Warranty Parts Center on the topics of parts retention, parts preparation for shipping, and administration.

NHTSA · Herstellerbulletin10243651Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.

NHTSA · Herstellerbulletin10139099Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringSonstigesNA

Bulletin

This informational bulletin is a revision for 10-00-89-005B to add the 2014 model year and labor codes.

NHTSA · Herstellerbulletin10139026Modelljahre 2008Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.

NHTSA · Herstellerbulletin10135290Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringSonstigesNA

Bulletin

This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near

NHTSA · Herstellerbulletin10116912Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles.

NHTSA · Herstellerbulletin10113662Modelljahre 2003Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

Isuzu: 2008 ascender. It may develop a crack in the exhaust manifold which will cause increased exhaust noise. *rm

NHTSA · Herstellerbulletin10041391Modelljahre 2008Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Izuzu: 2006 ascender. The malfunction light won't turn on when there is a fault in the air injector system. *rm

NHTSA · Herstellerbulletin10039116Modelljahre 2006Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringSonstigesNA

Bulletin

Pass-thru programming only for 2008 model year. *nj

NHTSA · Herstellerbulletin10022919Modelljahre 2008Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringSonstigesNA

Bulletin

Product enhancement for inventory and customer vehicles - obd system improvement. *kb

NHTSA · Herstellerbulletin10022538Modelljahre 2006Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringGetriebeNA

Bulletin

Malfunction indicator lamp (mil) on, diagnostic trouble code (dtc) p0894, harsh 1-2 shift with 4l60-e auto transmission. *kb

NHTSA · Herstellerbulletin10021354Modelljahre 2006Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Service update for inventory and customer vehicles fuel sending unit port fracture-extended starts/sluggish acceleration/check engine light-expires with base warranty. *kb

NHTSA · Herstellerbulletin10021202Modelljahre 2007Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

Reduced engine power mil illuminated. *kb

NHTSA · Herstellerbulletin10021196Modelljahre 2006Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Malfunction indicator lamp illuminated with engine cooling fan system performance dtc p0483 currently set or stored in history. *kb

NHTSA · Herstellerbulletin10020538Modelljahre 2007Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringGetriebeNA

Bulletin

Product enhancement for inventory vehicles only engine/powertrain control module reprogram. *kb

NHTSA · Herstellerbulletin10020535Modelljahre 2007Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringGetriebeNA

Bulletin

Oil life monitoring system - powertrain control module (pcm) reset. *tt

NHTSA · Herstellerbulletin10016591Modelljahre 2004Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringElektrikNA

Bulletin

Onstar system inoperative onstar system status light is red radio locked in phone mode or dtc b1000. *eh

NHTSA · Herstellerbulletin10014832Modelljahre 2003Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Ältere →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).