Bulletin
"Forward Collision Warning (FCW) Unavailable Service Required"-Meldung oder Warnleuchte „Service Active Lane Management“ EIN
🔔 Kostenloses Konto anlegen und Benachrichtigungen zu Jeep Cherokee (alle generationen) erhalten
Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
"Forward Collision Warning (FCW) Unavailable Service Required"-Meldung oder Warnleuchte „Service Active Lane Management“ EIN
Loss Of Driver?s Power Seat Position Functions
Flash: Drivetrain Control Module (DTCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) or warning lamp illumination. Upon further investigation the technician may find that the multiple Diagnostic Trouble Codes (DTCs) have been set: ? C1403-29 - Transfer Case Range Position Sensor-Signal Invalid. ? C14AA-62 - Transfer Case Motor Position Sensor Supply-Signal Compare Failure. This bulletin involves reprogramming the DTCM with the latest software available.
Engine Coolant Leak Coolant leak under vehicle and/or low coolant warning on dash. This bulletin involves inspecting and replacing the ECT sensor if required.
Right Front A-Pillar Sealing Plug Missing This bulletin involves inspecting and if necessary, installing the right front A-Pillar sealing plug and removing the door to check electrical connector. The customer may notice or describe they see a hole where a plug should be when opening the right front door of the vehicle.
Trailer Tow Lamps Inoperative After Mopar Trailer Tow Wiring Installation
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following DTCs have been set: P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. P2C90 - Crankcase Ventilation System - Hose "A" Disconnected. P1D73 - AGS performance fault. P04FC - Crankcase Ventilation System Performance. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation(Enlarged Europe and Middle East/Africa) only equipped with Gas ParticulateFilter (GPF))(DTC will set when driving above 72 kph (45 mph). P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P050B - Cold Start Ignition Timing Performance. P258B - Electric Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P2B95 - Cold Start Injection Pulse Performance. P062A - Fuel Pump Control Performance. P058C - Battery Monitor Module Temperature Monitoring Performance. P0607 - ECU Internal Performance. Injector performance faults for cylinders 2 - 4 map to DTC for incorrect cylinders. In addition the following software enhancement are included: AGS stuck condition (The customer won't see an issue, but this calibrationallows AGS performance fault - P1D73, to work correctly). Software corrects an issue with the wrong cylinder identification if an injectorcircuit performance fault is set in the PCM: If any of the series of injector control circuit faults are set, please refer tothe bullet-pointed list below to determine which injector to address.
Uconnect Market Place APP Fatal Error Message
Transmission Case Oil Leak This bulletin involves tightening the lower transmission bolts to updated torque specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set:P04FC - Crankcase Ventilation System Performance. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation(EMEA only equipped with Gas Particulate Filter (GPF))(DTC will set when driving above 72 kph (45 mph). P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P050B - Cold Start Ignition Timing Performance. P258B - Electric Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P2B95 - Cold Start Injection Pulse Performance. P062A - Fuel Pump Control Performance. P058C - Battery Monitor Module Temperature Monitoring Performance. P0607 - ECU Internal Performance. Injector performance faults for cylinders 2 - 4 map to DTC for incorrect cylinders. In addition the following software enhancement are included:Software corrects an issue with the wrong cylinder identification if an injector circuit performance fault is set in the PCM:If any of the series of injector control circuit faults are set, please refer to the bullet-pointed list below to determine which injector to address.For reference, the correct injector circuit performance faults are listed below:P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. Customers may also experience the following condition:Audible noise from the Low Temperature Radiator (LTR) coolant pump, at low speeds. Abnormal noise from the radiator cooling fan. LTR runs too long after the engine is turned off.
Damper - steering
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DiagnosticTrouble Code (DTC): U0418 - Implausible Data Received From Brake System Control Module. DTC U0418 can be set erroneously due to a low battery (below 10 volts).
Damper - steering
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs: P1D83 - Implausible Engine Oil Temperature Signal Received. P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit P0616 - Starter Control Circuit Lo. - Starter Control Circuit High. P0607 - ECU Internal Performance
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High. P0607 - ECU Internal Performance. P3032 - Barometric Pressure Sensor Performance
Rear Wheels Rubbing On Splash Shields/Wheel Liners This bulletin involves inspecting for the wrong size tire and wheel assemblies and possibly replacing all five wheel assemblies, Tire Pressure Monitoring (TPM) sensors, flashing the Electronic Power Steering (EPS) and performing a Proxi alignment. Customers may experience the following condition:The rear 17 in. tires are rubbing on the wheel liners. This condition is due to an incorrect 17 in. tire and wheel size, for the North Edition packages that require 18 in. tires and wheels.
Heater Hoses Installed Incorrectly This bulletin involves inspecting the heater hoses and possibly draining the engine coolant, swapping the heater hoses and refilling the engine coolant. Some vehicles may have been built with one or more of the following:Heater hoses installed in reversed order. If the coolant was drained and replaced, a sign the heater hoses are reversed is the vehicle will also make a gurgling noise.
Trailer Tow Lamps Inoperative After Mopar Trailer Tow Wiring Installation
Right Front A-Pillar Sealing Plug Missing This bulletin involves inspecting and if necessary, installing the right front A-Pillar sealing plug and removing the door to check electrical connector. The customer may notice or describe they see a hole where a plug should be when opening the right front door of the vehicle.
This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience one or more of the following conditions: During a limp mode condition, the transmission remains in a fixed gear. 5-4 downshift hesitation. A longer than normal delay during a shift from reverse to drive selection. In addition the following enhancements are included.
Uconnect Market Place APP Fatal Error Message
A-Pillar Water Leak This bulletin involves partially removing both front wheel liners and adding spray foam near the body load beam ends, on each side of the vehicle. Customers may comment on the following:Wet front carpets inside the cabin near the driver, passenger or both, front floor A-pillar areas.
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P2610 - PCM Internal Engine Off Timer Performance. U1504 - Implausible Message Data Length Received From Steering Angle Sensor. U1424 - Implausible Engine Torque Signal Received DTC False Failure. P2097 - Downstream Fuel Trim System 1 Rich DTC Calibration Robustness Improvement. P2099 - Downstream Fuel Trim System 2 Rich DTC Calibration Robustness Improvement. U0402 - Implausible Data Received. B10EA - Blower Motor Control Circuit High. B10E9 - Blower Motor Control Circuit Low. P0456 - EVAP System Small Leak. In addition, the following software enhancements are available:Calibration update to allow the throttle body to be cycled while the engine is off, for diagnostic purposes. Calibration update for a slight push in the vehicle that may be felt when coasting down during a 8th to 7th gear downshift. Vehicle shudder at stop/start with A/C on.
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one of the following DTCs have been set:P1D83 - Implausible Engine Oil Temperature Signal Received. P0556 - Brake Booster Pressure Sensor Circuit Performance. U0428 - Implausible Data Received From Steering Angle Sensor Module. U1504 - Implausible Message Data Length Received From Steering Angle Sensor. C0501 - Left Front Wheel Speed Sensor Range/Performance. C0507 - Right Front Wheel Speed Sensor Range/Performance. C050D - Left Rear Wheel Speed Sensor Range/Performance. C0513 - Right Rear Wheel Speed Sensor Range/Performance. Erroneously set wheel speed sensor DTCs listed above will not turn on the MIL by design but may be found during a vehicle diagnostic scan.Some customers may also experience the following:The engine being too quick to shut down when coming to a stop in Engine Stop/Start (ESS) mode. During an engine limp mode condition, the transmission remains in a fixed gear. In addition, the following software enhancements are available: Calibration update to allow the throttle body to be cycled while the engine is off, for diagnostic purposes. Calibration update for ESS to allow the engine to remain running during a brief stop.
Transmission Case Oil Leak This bulletin involves tightening the lower transmission bolts to updated torque specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).