Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
Some 2019 MKC vehicles without lane keep assist may exhibit an AdvanceTrac/hill start assist message(s) and/or illuminated electronic stability control/traction control indicator lamp with diagnostic trouble codes (DTCs) U0420 stored in the anti-lock brake (ABS) module and U0415 stored in the power steering control module (PSCM). This concern may also result in additional DTCs. DTCs U0420 and U0415 may have been set as a result of low system voltage during a vehicle start. The PSCM may have a communication fault with the ABS module when it reacts to low voltage when the key is on. To correct the condition, replace the ABS control module using the service part number KJ7Z-2C219-C. For claiming, use causal part 2C219 and applicable labor operations in Section 02 of the Service Labor Time Standards (SLTS) Manual.
Some 2016-2017 Ford and Lincoln vehicles with a new body control module (BCM) installed may exhibit a programming error when using IDS versions 122.03 through 123.01 stating 'Data Corrupt' or 'Configuration Failed, would you like to retry?'. IDS scan tool version 123.02 contains a fix for this programming error. Install IDS version 123.02 or later from PTS > Rotunda tab > Diagnostic Tool Support > Download Software. Once installed, perform the BCM programmable module installation (PMI). Refer to Workshop Manual (WSM), Section 419-10 > Removal and Installation.
Some 2016-2017 Ford and Lincoln vehicles with a new Body Control Module (BCM) installed may exhibit a programming error using IDS v122.03 and newer stating "Data Corrupt" or Configuration Failed, would you like to retry?. A temporary work around has been released to complete the BCM programming process. Uninstall IDS from the computer. Run the IDS clean up utility tool located on PTS > Rotunda Tab > Diagnostic Tool Support > IDS Support > IDS troubleshooting guide. Install IDS v122.01 (122_FULL) by copying the following link into an internet address bar https://www.fordservicecontent.com/Ford_Content/IDS/SoftwareUpdates/IDS-122.01_full.exe. Retry the BCM Programmable Module Installation (PMI) using IDS level 122.01. Monitor OASIS for updates.
2019 MKC - Without Lane Keep Assist AdvanceTrac, Hill Start Assist Message(s) And/Or Stability Control Indicator Lamp Illuminated With DTCs U0420 And U0415 Some 2019 MKC vehicles without lane keep assist may exhibit an advancetrac, hill start assist message(s) and/or the electronic stability control/traction control indicator lamp illuminated with diagnostic trouble codes (DTCs) U0420 stored in the anti-lock brake module (ABS) and U0415 stored in the power steering control module (PSCM). This concern may also result in additional DTCs. DTCs U0420 and U0415 may have been inadvertently set as a result of low system voltage during a vehicle start. To resolve the concern, reprogram the ABS control module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 3504 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Some 2013-2015 Fusion/MKZ/Escape/MKC with a 1.6L GTDI, 1.5L GTDI, or 2.0L GTDI may exhibit a lack of power, loss of power, or stall when placed in gear with DTCs P00C6, P0087, P008A, P008B, P018C, or P018D. If normal diagnosis leads to a biased or failed Fuel Low Pressure (FLP) sensor, the sensor is available without the need to order the entire fuel line assembly. The FLP sensor, located on the fuel supply line to the high pressure pump, provides the low side fuel pressure input to the PCM so the Fuel Driver Module can be controlled accordingly. The FLP PID can be viewed in the Datalogger and then compared to a manual pressure gauge per pinpoint test HC in the PCED to validate the sensor is working properly. The Fusion/MKZ catalog has been updated to show the sensor availability.
Some 2019 Escape and MKC vehicles built on 15-Feb-2019 and through 12-Mar-2019 may exhibit a whistle noise from the heating ventilation and air conditioning (HVAC) evaporator core cover area where the evaporator tubes enter the evaporator case in the passenger footwell area. The noise will be most noticeable while transitioning into maximum heat with higher blower speeds. This may be due to incorrect evaporator core cover to evaporator case sealing that can allow an air leak and result in a whistle noise. To correct the condition, follow the Service Procedure steps to apply a small piece of mastic sealing patch to the evaporator case/cover joint.
Some 2019 MKC vehicles without lane keep assist may exhibit an advancetrac, hill start assist message(s) and/or the electronic stability control/traction control indicator lamp illuminated with diagnostic trouble codes (DTCs) U0420 stored in the anti-lock brake module (ABS) and U0415 stored in the power steering control module (PSCM). This concern may also result in additional DTCs. DTCs U0420 and U0415 may have been inadvertently set as a result of low system voltage during a vehicle start. To resolve the concern, reprogram the ABS control module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 2C219 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 47910 - 2019 MKC - Without Lane Keep Assist Advance Trac, Hill Start Assist Message(s)And/Or Stability Control Indicator Lamp Illuminated With DTCs U0420 And U0415 Some 2019 MKC vehicles without lane keep assist may exhibit an advance trac, hill start assist message(s) and/or the electronic stability control/traction control indicator lamp illuminated with diagnostic trouble codes (DTCs) U0420 stored in the anti-lock brake module (ABS) and U0415 stored in the power steering control module (PSCM). This concern may also result in additional DTCs. DTCs U0420 and U0415 may have been inadvertently set as a result of low system voltage during a vehicle start. If a vehicle exhibits DTCs U0420 and U0415, charge the battery, clear codes and restart engine. If DTC U0420 and DTC U0415 do not reset, no further action or repair is necessary. If DTC U0420 and U0415 do reset, refer to Workshop Manual (WSM), Section 206-09 for normal diagnostics. Engineering is investigating, monitor OASIS for updates.
Some 2018 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition, remove the TCU fuse for 5 minutes then reinstall. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
2017 vehicles equipped with a 2.0L GTDI, 2.3L GTDI, or 2.5L PFI engine will either be equipped with a diamond washer on each side of a smooth-faced crankshaft timing sprocket (early build), or a crankshaft timing sprocket with laser etched faces and no diamond washers (late build). If equipped, diamond washers should be cleaned, inspected and reused, if undamaged. Diamond washers should never be installed along with a laser etched crankshaft timing sprocket. Related WSM procedure information is in the process of being updated.
Some 2017-2018 Escape/MKC and 2017 Edge vehicles equipped with 2.0L Gasoline Turbocharged Direct Injection(GTDI) engines may exhibit illuminated malfunction indicator light(MIL) with DTC P04DB(crankcase ventilation system disconnected) stored in Powertrain Control Module(PCM) memory. Disconnect crankcase pressure sensor electrical connector and remove crankcase vent tube. Inspect valve cover port with borescope. If flashing is confirmed in crankcase vent tube port replace GB5Z-6582-B valve cover(Reference Workshop Manual 303-01A Engine- 2.0L Ecoboost Removal and Installation). Engineering is currently investigating. To assist with the investigation, refer to the Professional Technician Society (PTS) website and use the report a vehicle concern link at the bottom of the OASIS report.
Some 2016-2017 Ford/Lincoln vehicles SYNC 3 may exhibit an intermittent blank screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or blank screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Some customers with 2016 lincoln vehicles (excluding lincoln mkx) equipped with sync 3 version 1.0 or 1.1 may request an upgrade to their sync system for apple carplay or android auto functionality. This upgrade requires sync 3 version 2.2 software to be installed for both applications to function. In addition, apple carplay requires a new media hub/universal serial bus (usb) hub to be installed. For correct media hub/universal serial bus (usb) hub part number refer to the ford catalog advantage (fca) web version of the parts catalog. The sync version can be confirmed via oasis. The software and hardware upgrade is not a warranty repair per the warranty and policy manual, section 3, warranty coverages sync.
Ford: Some vehicles and trucks are experiencing a malfunction with the heated steering wheel becoming inoperative and on demand test failure. Model 2014-15 fusion, 2011-15 mkx, 2013-15 super duty, explorer, taurus, mks, mkt, 2015 f-150, mkz, mkc, 2011-15 mkx. *pe
Lincoln/ford: Once procedure for heated steering wheel module program completed, heated steering wheel fails to operate properly and passes network test but fails on demand self test. Model 2011-15 fusion f-150, explorer, taurus, super duty, mkz, mkc, mks, mkt, mkx. *pe
Ford fusion/mkz, 2015 mkc, 2015 mustang- bulletin regarding intermittently, the steering column controls fails with possible uo212 in multiple modules. *lj
Ford/lincoln: On some vehicles, volume will go to maximum or minimum level when plus or minus button is pushed on steering wheel. Model 2015 mustang, mkc. *pe
Lincoln: Diagnostic trouble code (dtc) u0415 may appear in power steering control module (pscm) and return after a short time and can be disregarded unless specifically related to electronic power assist steering (epas) system. Model 2015 mkc. *pe
Lincoln/ford: On some vehicles, the instrument panel cluster (ipc) needs replacing due to programmable module installation (pmi) not able to perform. Model 2013-14 fusion, mkz, 2015 mkc. *pe
Lincoln: A false diagnostic trouble code u0159 may occur during delivery of vehicle concerning the power steering control module (pscm) with an active park assist and will not impact function of active park assist or steering system model 2015 mkc. *pe
Ford/lincoln: Diagnostic trouble code (dtc) p025a (fuel pump module a control circuit/open) has concern of crank no start or stall due to unpowered fuel pump control module in transport mode. Model 2015 mkc, mkz, fusion. *pe
Ford: Due to an unpowered fuel pump control module, the remote start feature will exhibit a diagnostic trouble code (dtc) p025a, with crank no start or stall, while in transport mode. Model 2015 mkc. *pe
Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
Demonstration/Delivery Hold - Application Performance Upgrade 15A03 Certain 2016 Model Year Escape, MKC, Exkpedit;ion, and Navigator Vehicles Sync 3 Software Updates
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).