Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Mazda 2

2002– · 3 generationen · 13 dokumentierte Mängel · 7 Märkte
Generationen

Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.

SchweregradAlleMittelGering
Modelljahr
MarktAlleNA
2 III · 2014–
BulletinMittelElektrikNA

Bulletin

Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.

NHTSA · Herstellerbulletin10199641Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinMittelElektrikNA

Bulletin

If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.

NHTSA · Herstellerbulletin10185813Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Some customers may complain about any of the following 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative.

NHTSA · Herstellerbulletin11039110Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Some vehicles may exhibit the check engine light ON with DTC P0300:00 (Random misfire detected) stored. This may be caused by a mis-detection of a misfire due to improper PCM control logic. To eliminate this concern, the PCM control logic has been modified.

NHTSA · Herstellerbulletin11012337Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Some customers may notice the charging lamp turns on while driving. Upon inspection, DTC P2502:00 PCM (Malfunction in voltage generated by generator) is stored in memory. This may be caused by resistance between the circuit board and ground. When high intensity electrical current passes through, the ground terminal position may not be sufficient enough. To eliminate this concern, the DC-DC converter control software has been modified. Additionally, the production procedure has been revised. The tightening torque for the ground terminal and circuit board was increased.

NHTSA · Herstellerbulletin11008418Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Some customers may experience a check engine light illumination at idle while stopped with DTC P0300:00 stored, resulting in rough idle conditions. P0300:00: Random misfire detected This concern is caused by improper engine control in the idle range. To eliminate the concern, the PCM control software has been modified.

NHTSA · Herstellerbulletin11008417Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

BSM Radar aiming cannot be performed after rightside BSM control module rekkplacement

NHTSA · Herstellerbulletin10213434Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Some customers may experience the CHECK ENGINE light ON with DTC P0089:00 (Spill valve control solenoid valve control circuit range/performance problem) stored. This is caused by improper control software of the PCM detecting a false error, even with normal fuel pressure operation. To correct this issue, the control software of the PCM has been modified.

NHTSA · Herstellerbulletin10190951Modelljahre 2021Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Replace the Active Driving Display.

NHTSA · Herstellerbulletin10185954Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone. P2096:00 - Air fuel too lean P2097:00 - Air fuel too rich P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern.

NHTSA · Herstellerbulletin10180595Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display.

NHTSA · Herstellerbulletin10188483Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.

NHTSA · Herstellerbulletin10186918Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Active driving display opens/closes improperly. Some vehicles may exhibit the active driving display opening/closing improperly as described below: * It does not open or close when the ignition is turned ON or OFF . * The display operation does not fully open/close. * It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the act ive driving display which activates pinching detection. Customer having this concern should have their vehicle repaired using the following repair procedure.

NHTSA · Herstellerbulletin10186257Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Some customers may experience the active driving display (auto flip-up type) does not flip up and no DTC is stored. Due to improper assembly, a deformed bracket may cause a loose mesh between internal gears. To correct this issue, the active driving display has been changed.

NHTSA · Herstellerbulletin10144332Modelljahre 2018Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Replace the Active Driving Display.

NHTSA · Herstellerbulletin10125470Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.

NHTSA · Herstellerbulletin10105642Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.

NHTSA · Herstellerbulletin10101468Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the active driving display. Replace the active driving display.

NHTSA · Herstellerbulletin10101464Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.

NHTSA · Herstellerbulletin10091601Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the active driving display. Replace the active driving display.

NHTSA · Herstellerbulletin10090902Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.

NHTSA · Herstellerbulletin10090667Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 III · 2014–
BulletinGeringElektrikNA

Bulletin

Bsm radar aiming cannot be performed after right-side bsm control module replacement. If right-dide bsm control module requres replacement for any repair, also replace left side bsm control module to compelte the radar aiming procedure (it's ok to replace the left bsm alone). If the right-side bsm control module is replaced alone, "automatic configuration" is not performed due to program error in module. Because of this, the required "bsm radar aiming" cannot be performed. "automatic configuration" as well as "bsm radar aiming" can be performed if left-side bsm control module is replaced alone or together with right-side bsm control module.

NHTSA · Herstellerbulletin10076685Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 II · 2007–2014
BulletinGeringElektrikNA

Bulletin

Mazda: There is possible excessive condensation or water inside the headlamp unit on many mazda models. *rm

NHTSA · Herstellerbulletin10037949Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
2 II · 2007–2014
BulletinGeringElektrikNA

Bulletin

Mazda: There is condensation and fog in the front and rear combination lights. *rm

NHTSA · Herstellerbulletin10037655Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).