Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Mazda MX-30

2020– · 1 dokumentierte Mängel · 4 Märkte

Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.

SchweregradAlleMittelGering
Modelljahr
BulletinMittelKarosserieNA

Bulletin

DESCRIPTION Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. Symptom 2: The touch sensor of the front door outer handle does not unlock the doors. Door outer handle touch sensor for locking (1) / unlocking (2) NOTE: If the concern occurs after specific operation as described below, refer to the TSB 09-046/22 (DOOR OUTER HANDLE TOUCH SENSOR DOES NOT LOCK AND UNLOCK AFTER A SPECIFIC OPERATION). 1. [MX-30] After using cabin preconditioning or hazard warning lights for approx.15 minutes. 2. [MAZDA3 and CX-30] After using hazard warning lights for approx. 15 minutes. 3. [MAZDA3, CX-30 and MX-30] When both touch sensors are touched at once. Cause 1 (for Symptom 1): Water may accumulate around the touch sensor in the outer handle, resulting in temporary lower sensitivity of the capacitive sensor. Also, if car wash foam gets inside the outer handle while washing the vehicle, the foam may disturb the touch sensor detection. Mazda is still working on a mass production change for this concern. Cause 2 (for Symptom 2): Improper soldering in the production process may disturb the touch sensor detection. To eliminate this concern, the production process has been modified. Customers having this concern should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE 1. Verify customer concern. 2. Repair the vehicle depending on the experienced symptom(s). Symptom 1: Follow the "Procedure to waterproof a touch sensor below to make the touch sensor waterproof. Symptom 2: Replace the front outer handle with a modified one according to the instructions on MGSS. Mazda3 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) CX-30 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) MX-30 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) If both symptoms are experienced: Replace the front outer handle with a modified one and follow the Procedure to waterproof a touch sensor below to make the touch sensor waterproof. NOTE: DO NOT repair the other front outer handle for the vehicle if it is not experiencing any problems. 3. Verify the repair by checking if the new outer handle locks/unlocks the door correctly.

NHTSA · Herstellerbulletin11030603Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelElektrikNA

Bulletin

Some customers may experience the master warning light and/or the "In-Vehicle Network Malfunction" warning message in the instrument cluster on with DTC B119F:01 (TCU - Tel antenna No. 1 malfunction) stored.

NHTSA · Herstellerbulletin11003361Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelBremsenNA

Bulletin

Some customers may experience the following concerns: The liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. The auto close operation of the power liftgate is not performed (The liftgate can be closed manually). To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified. Customers

NHTSA · Herstellerbulletin11003356Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelBremsenNA

Bulletin

Einige Kunden können feststellen, dass sich die Heckklappe oder der Kofferraumdeckel nicht entriegeln lässt, obwohl das Fahrzeug geparkt und die Zündung ausgeschaltet ist. Wenn der Motor läuft (POWER ON) oder die Zündung eingeschaltet ist (READY ON), lässt sie sich entriegeln. Um dieses Problem zu beseitigen, wurde die Steuerungssoftware des DSC HU/CM (bzw. der elektronisch gesteuerten Bremseinheit) geändert.

NHTSA · Herstellerbulletin10254184Modelljahre 2023Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelKarosserieNA

Bulletin

Einige Kunden können feststellen, dass bei einem bestimmten Vorgang der Berührungssensor des vorderen Türaußengriffs die Türen nicht ver- und entriegelt, der Funksender jedoch einwandfrei funktioniert. Beschreibung der bestimmten Vorgänge: Bestimmter Vorgang 1 [MX-30]: Nach Verwendung der Innenraumvorkonditionierung oder der Warnblinkanlage für ca. 15 Minuten. Bestimmter Vorgang 2 [MAZDA3 und CX-30]: Nach Verwendung der Warnblinkanlage für ca. 15 Minuten. Bestimmter Vorgang 3 [MAZDA3, CX-30 und MX-30]: Wenn beide Berührungssensoren gleichzeitig berührt werden. Ursache für bestimmte Vorgänge 1 und 2: Der Berührungssensor wurde deaktiviert, um unbeabsichtigte Ver- und Entriegelungsvorgänge durch Regen zu vermeiden. Ursache für bestimmten Vorgang 3: Die Steuerlogik ist nicht angemessen. HINWEIS: Tritt das Problem ohne die oben genannten bestimmten Vorgänge auf, siehe TSB 09-019/22 (DER BERÜHRUNGSSENSOR DES TÜRAUSSENGRIFFS VER- UND/ODER ENTRIEGELT NICHT). Zur Behebung dieses Problems wurde die Steuerungssoftware der LF-Steuereinheit (LFU) geändert.

NHTSA · Herstellerbulletin10252505Modelljahre 2022Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelKarosserieNA

Bulletin

Some customers may complain that oil leaks from the rear shock absorber. Due to the structure, a small amount of oil is leaked out, but there is no functional concern. However, this oil leak level is almost the same where shock absorber replacement is required. To eliminate this concern, the structure of the oil seal in the rear shock absorber has been modified

NHTSA · Herstellerbulletin10244579Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA02_11046). Ver. 7000C0A-NA02_11046 fixes these software errors (bugs): The system does not resume the play list after editing a play list for an USB audio device. The screen does not show proper picture when receiving SiriusXM data. Ver. 7000C0A-NA02_11044 fixes these software errors (bugs): Beep sounds every couple of minutes. Language setting may not be accepted correctly. When refusing the incoming call while playing audio tracks using the Apple CarPlay, the screen shows Phone in use message and it stops playing audio tracks. The audio track may not pause when pressing the mute button. The screen freezes when smartphone receives messages under Bluetooth connection. Ver. 7000C0A-NA02_11036 fixes these software errors (bugs): Screen freezes and goes to white screen, then the system reboots. Cannot control the audio system with steering switches and command switch. If another incoming call comes in immediately after the hands-free call is ended, the call is automatically accepted. Establishing Bluetooth connection takes tiime. DTC U3000:49 is stored which may be accompanied with following symptoms. -No sound comes out from the speakers. -Audio source selection is unavailable. The vehicle icon rotates when using the navigation with "head-up" mode.

NHTSA · Herstellerbulletin10238677Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelSonstigesNA

Bulletin

Some customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.

NHTSA · Herstellerbulletin10237206Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelKarosserieNA

Bulletin

Einige Kunden könnten sich über Ölaustritt am hinteren Stoßdämpfer beschweren. Aufgrund der Konstruktion tritt eine geringe Menge Öl aus, es liegt jedoch keine funktionelle Beeinträchtigung vor. Allerdings entspricht dieses Ausmaß des Ölaustritts nahezu dem Niveau, bei dem ein Austausch des Stoßdämpfers erforderlich wäre. Um dieses Problem zu beseitigen, wurde die Konstruktion der Öldichtung im hinteren Stoßdämpfer geändert.

NHTSA · Herstellerbulletin10233659Modelljahre 2022Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelSonstigesNA

Bulletin

Some customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.

NHTSA · Herstellerbulletin10233569Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

Einige Fahrzeuge können während der PDI-Probefahrt oder während der ersten Kilometer nach der Auslieferung an den Kunden ein Lenkradflattern oder Karosserievibrationen aufweisen, die auf Flachstellen an den Reifen zurückzuführen sind. Flachstellen an Reifen können durch unsachgemäße Wartung während der Lagerung beim Händler verursacht werden (z. B.: Das Fahrzeug stand über einen längeren Zeitraum bei hohen Umgebungstemperaturen unbewegt).

NHTSA · Herstellerbulletin10232302Modelljahre 2022Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelBremsenNA

Bulletin

Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

NHTSA · Herstellerbulletin10230875Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelSonstigesNA

Bulletin

Einige Kunden können sich beschweren, dass Mazda Connect nicht startet (schwarzer Bildschirm) oder dass es nach dem Starten des Fahrzeugs lange dauert, bis es neu startet bzw. neu hochfährt. Ursache ist, dass der Initialisierungsvorgang des CMU beim Start aufgrund eines defekten Leiterplattenbauteils fehlschlägt. Um dieses Problem zu beseitigen, wurde die interne Hardware (DRAM) des CMU verbessert.

NHTSA · Herstellerbulletin10226898Modelljahre 2022Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelKarosserieNA

Bulletin

Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: - Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. - Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning lights for approx. 15 minutes. - Specific Operation 3 [MAZDA3, CX-30 and MX-30]: When both touch sensors are touched at once. - Specific Operation 1 and 2 Cause: The touch sensor has been disabled to avoid the unintended locking/unlocking operation caused by rain. - Specific Operation 3 Cause: The control logic is not appropriate. To correct this issue, the control software of the LF control unit (LFU) has been modified.

NHTSA · Herstellerbulletin10226892Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelBremsenNA

Bulletin

Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: * The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: - The windshield is dirty - The FSC lens is foggy - There is low visibility due to rain, fog or snow - It is at night and there is not enough light - There is direct or reflected sunlight on the FSC - There is problem with the FSC * There is a problem with the AUTOHOLD control function. * There is a problem with the electric parking brake (EPB).

NHTSA · Herstellerbulletin10225763Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

The Blind Spot Monitoring (BSM) system can malfunction with the following symptoms if the rear side radar sensors are installed facing the wrong direction. - BSM system indicates vehicle on the opposite side. - i-ACTIVSENSE indicator ring will not turn green - Rear Cross Traffic Alert (RCTA) does not work - Rear side radar sensor

NHTSA · Herstellerbulletin10222563Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelSonstigesNA

Bulletin

Some customers may complain that Mazda Connect does not start or that it takes a long time to restart after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware of the CMU has been improved.

NHTSA · Herstellerbulletin10218768Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelBremsenNA

Bulletin

This information will give you the necessary knowledge to respond to customers concerns of Smart Brake Support (SBS) unintended braking. By educating the customer on the system operation, it should reduce their anxiety or distrust of the vehicle.

NHTSA · Herstellerbulletin10218772Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

Some vehicles may exhibit a steering shimmy or body vibration during the PDI test drive or during the first few miles of driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).

NHTSA · Herstellerbulletin10213147Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · Herstellerbulletin10210902Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

Some customers may complain about the infotainment system and/or the MyMazda App showing incorrect tire pressures and/or tire pressure missing. This may be caused by: Incorrect calendar entry (month/day/year) after a battery disconnect *Infotainment system software update. *BCM TPMS unlearn during vehicle storage or transport. *Wheel/Tire change

NHTSA · Herstellerbulletin10209755Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelFahrwerkNA

Bulletin

Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Use a clean towel damped in leather/vinyl cleaner or mild soap to clean the steering wheel. NOTE: Upholstery maintenance and care information can also be found in the Owner's Manual.

NHTSA · Herstellerbulletin10208554Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelElektrikNA

Bulletin

Some vehicle may experience the i-ACTIVSENSE/ALH warning lights on and a system error messages may be found in the center display as well. DTC U3000:04 (FSC) is stored in memory DTC U3000:04 (FSC) - Forward sensing camera (FSC) internal malfunction This may be caused by a hardware failure in an internal device of the FSC that results in the malfunction detection. To eliminate this concern, the production process of the FSC has been modified.

NHTSA · Herstellerbulletin10206960Modelljahre 2022Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelBremsenNA

Bulletin

## Unerwartete Funktion der Smart Brake Support (SBS-R) beim Rückwärtsfahren Einige Kunden können sich über eine unerwartete Kollisionswarnung oder automatische Bremsung beim Rückwärtsfahren unter bestimmten Bedingungen beschweren, etwa wenn sich hinter dem Fahrzeug eine Stufe oder ein Objekt auf der Straße befindet. Dies wird dadurch verursacht, dass die Steuerungssoftware der Einparkhilfe der Smart Brake Support (SBS-R) unter bestimmten Bedingungen unbeabsichtigt erkennt. Um dieses Problem zu beheben, wurde die Steuerungssoftware der Einparkhilfe geändert. Kunden mit diesem Problem sollten ihr Fahrzeug nach dem folgenden Reparaturverfahren instand setzen lassen.

NHTSA · Herstellerbulletin10206010Modelljahre 2022Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinGeringElektrikNA

Bulletin

DESCRIPTION Some vehicles may continue to display the recall notification "IMPORTANT NOTICE. VIEW VEHICLE STATUS MONITOR FOR DETAILS" on the center display even after the recall has been completed. NOTE: Once the warranty claim for the recall campaign is approved by Mazda Japan, the recall notification will be automatically removed via Connected Services on the following day or later. This condition may occur if the Connected Services subscription was canceled while the recall notification was still active. ACTION TO BE TAKEN If you encounter the situation above, use MDARS to manually remove the center display recall notification. Note: MDARS can only remove the recall notification when MCVV shows no CV contract.

NHTSA · Herstellerbulletin11037008Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Ältere →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).