Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Mini Mini II

2006–2013 · 18 dokumentierte Mängel · 2 Märkte

Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.

SchweregradAlleMittelGering
Modelljahr
BulletinMittelMotorNA

Bulletin

## Dichtheitsprüfung der Klimaanlage Der Kunde beanstandet eine schlechte oder fehlende Kühlleistung der Klimaanlage. Nach weiterer Diagnose wird festgestellt, dass dem System Kältemittel fehlt oder es nahezu leer ist, mit einem elektronischen Lecksucher lässt sich jedoch kein Leck finden. URSACHE: In den meisten Fällen reicht ein elektronischer Lecksucher nicht aus, um kleine Lecks im System zu finden. Elektronische Lecksucher können Fehlalarme auslösen und so zu einer falschen Diagnose kleiner Undichtigkeiten führen. Ein Leck lässt sich nicht genau lokalisieren, wenn die Zugänglichkeit eingeschränkt ist (bei Expansionsventil, Verdampfer oder Kondensator).

NHTSA · Herstellerbulletin10162461Modelljahre 2009Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelMotorNA

Bulletin

Bei der Motorölservice wird ein kleiner O-Ring im Ölfiltergehäuse gefunden. Es liegt keine Kundenbeschwerde vor. Während des planmäßigen Motorölservices bemerkt der Techniker einen schwarzen Gummi-O-Ring, der auf dem Boden des Motorölfiltergehäuses liegt. Der O-Ring hat sich aus dem Rückschlagventil im Inneren des Motorölfiltergehäuses gelöst. Durch den gelösten O-Ring entstehen keine nachfolgenden Motorschäden. Motorölfiltergehäuse (1) Gummi-O-Ring (2) Die Materialabmessungen des Gummi-O-Rings sind nicht zufriedenstellend, sodass er sich aus seiner Einbauposition lösen kann.

NHTSA · Herstellerbulletin10150347Modelljahre 2009Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelMotorNA

Bulletin

Der Kunde gibt an, dass von der Unterseite des Motors ein kleiner Motorölaustritt zu sehen ist. URSACHE Die interne Dichtung des Magnetventils zur Steuerung der Ölpumpenfördermenge ist beschädigt, wodurch Motoröl aus dem Magnetventil zur Ölpumpenfördermengensteuerung austreten kann.

NHTSA · Herstellerbulletin10150087Modelljahre 2011Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelMotorNA

Bulletin

Motorölleck. Der Kunde gibt an, dass von der Unterseite des Motors ein kleines Motorölleck zu sehen ist. URSACHE Die interne Dichtung des Magnetventils zur Volumenregelung der Ölpumpe ist beschädigt, wodurch Motoröl aus dem Magnetventil zur Volumenregelung der Ölpumpe austritt.

NHTSA · Herstellerbulletin10149500Modelljahre 2009Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelMotorNA

Bulletin

Serviceaktion: Kühlmittelpumpe ersetzen. Kühlmittel tritt an der Kühlmittelpumpe aus. URSACHE Das Kunststoffgehäuse der Kühlmittelpumpe kann Risse entwickeln. Diese Risse können zu einem Kühlmittelaustritt führen.

NHTSA · Herstellerbulletin10149501Modelljahre 2011Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelMotorNA

Bulletin

Motorölleck. Der Kunde gibt an, dass von der Unterseite des Motors ein kleines Motorölleck zu sehen ist. URSACHE Die interne Dichtung des Magnetventils zur Ölpumpen-Volumenregelung ist beschädigt, wodurch Motoröl aus dem Magnetventil zur Ölpumpen-Volumenregelung austritt.

NHTSA · Herstellerbulletin10149323Modelljahre 2011Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelMotorNA

Bulletin

## N16-Motor: Ölverlust an der Dichtkappe des Zylinderkopfs Am Dichtstopfen im Zylinderkopf, direkt unterhalb der Unterdruckpumpe, kann es zu einem Ölaustritt kommen. Der Dichtstopfen wurde bei der Produktion nicht ausreichend festgezogen.

NHTSA · Herstellerbulletin10148441Modelljahre 2009–2012Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelMotorNA

Bulletin

N16-Motor: Ölverlust an der Zylinderkopf-Dichtungsschraube An der Dichtungsschraube im Zylinderkopf, direkt unterhalb der Unterdruckpumpe, kann ein Ölverlust auftreten. URSACHE: Die Dichtungsschraube wurde bei der Produktion nicht ausreichend festgezogen.

NHTSA · Herstellerbulletin10148391Modelljahre 2009–2012Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelMotorNA

Bulletin

N16 und N18 Motorölleck. Der Kunde gibt an, dass von der Unterseite des Motors ein kleines Motorölleck zu sehen ist. URSACHE Die interne Dichtung des Magnetventils zur Steuerung des Ölpumpenvolumens ist beeinträchtigt, wodurch Motoröl aus dem Magnetventil zur Steuerung des Ölpumpenvolumens austritt.

NHTSA · Herstellerbulletin10148293Modelljahre 2009Automatisch übersetzt · Original: EnglischDetails ansehen →
BulletinMittelMotorNA

Bulletin

SI M11 01 12February 2015 EngineTechnical Service This Service Information bulletin supersedes SI M11 01 12 dated March 2014. designates changes to this revision SUBJECT N16 and N18 Engine: Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid. DIAGNOSTIC

NHTSA · Herstellerbulletin10147108Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

Mini: The timing chain tensioner developed an oil leak at mounting location, which was caused by the seal ring material being too soft, resulting in tension lost during tightening sequence of timing chain tensioner. Model 2010-2011 r55, r56, r57, r60 (cooper s clubman, convertible, countryman and hardtop). *pe

NHTSA · Herstellerbulletin10046760Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

Mini: On certain model vehicles, an engine oil leak may occur, due to the compromised oil pump volume control solenoid valve, from the underside of engine. No model years listed. *pe updated 4/19/2013. *kb updated 3/11/14. *pe

NHTSA · Herstellerbulletin10044680Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

Mini: Service engine soon is illuminated due to tank ventilation valve (tev) being jammed open and fuel cap, with evaporative system leakage, was incorrectly installed. *pe

NHTSA · Herstellerbulletin10043873Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinMittelMotorNA

Bulletin

Mini: Service engine soon or check gas cap warning is illuminated: Tank leakage. Leakage is detected in the tank ventilation or evaporative system. *pe

NHTSA · Herstellerbulletin10028785Modelljahre 2008Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

N18 engine high pressure fuel pump (hdp): limited warranty extension to 10 years/120,000 miles

NHTSA · Herstellerbulletin10216755Modelljahre 2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

MINI Water Pump Class Action Settlement

NHTSA · Herstellerbulletin10193497Modelljahre 2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

N16 ENGINE IGNITION COILS: LIMITED WARRANTY EXTENSION TO 10 YEARS/120000 MILES This Service Information bulletin supersedes SI M01 08 17 dated February 2018.

NHTSA · Herstellerbulletin10159154Modelljahre 2011–2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

"N18 Engine High-Pressure Fuel Pump (HDP): Limited Warranty Extension to 10 Years/120,000 Miles. For the above-referenced vehicles, MINI USA, a division of BMW of North America, LLC (""MINI USA"") is extending the limited warranty for the engine's High-Pressure Fuel Pump (HDP) to: 10 years/120,000 miles as determined by the vehicle's original in-service date Item #1: This ""componentspecific"" limited warranty extension applies to defects in materials and workmanship and is subject to the applicable vehicle and coverage eligibility requirements, exclusions and limitations that apply to the New MINI Passenger Car Limited Warranty. Important Note: This limited warranty extension only applies to the listed vehicles produced up to and including 2/29/2012 (Leap year). Vehicles produced on or after 3/1/2012 are fitted with different equipment. This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing this problem. Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release."

NHTSA · Herstellerbulletin10151221Modelljahre 2011–2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

Service Action: N14 Engine Retrofit Turbocharger Engine Oil Supply Line Heat Shield. After switching off the engine, the heat radiating from the turbocharger may cause the engine oil to solidify in the oil supply line to the turbocharger. This can lead to a restriction in the oil supply line, resulting in damage to the turbocharger bearings. CAUSE Close proximity of the turbocharger engine oil supply line and the turbocharger

NHTSA · Herstellerbulletin10150303Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

Service Action: N14 Engine Check Timing Chain Tensioner and Timing Chain. The timing chain tensioner applies pre-tension to the timing chain guide rail mechanism. In some cases, the tensioner spring force may be too low. Depending on the severity of the wear, it may lead to a rattling noise when starting the engine cold or when the engine is idling. CAUSE The timing chain tensioner internal tolerances are not consistent.

NHTSA · Herstellerbulletin10150202Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

Service Action: N14 Engine Check Timing Chain Tensioner and Timing Chain. The timing chain tensioner applies pre-tension to the timing chain guide rail mechanism. In some cases, the tensioner spring force may be too low. Depending on the severity of the wear, it may lead to a rattling noise when starting the engine cold or when the engine is idling. CAUSE The timing chain tensioner internal tolerances are not consistent.

NHTSA · Herstellerbulletin10147957Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

Surface Cracks on the Water Pump Drive Pulley. During a repair, service or inspection, the drive pulley on the water pump shows signs of cracking. No part replacement is necessary unless there is another issue found that will be corrected by replacing the drive pulley.

NHTSA · Herstellerbulletin10147906Modelljahre 2011Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

N18:MINI Fuel Additive. INFORMATION Because carbon deposit buildup is related to fuel quality, it is not considered a defect in the vehicle's materials or workmanship. Consequently, the use of MINI Fuel Additive as outlined in this bulletin is not covered under the terms of the MINI New Passenger Car Limited Warranty, MINI Maintenance Program, any applicable Federal, State or MINI Emissions Warranty or the MINI Next Certified Pre-Owned Limited Warranty. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/217...4/7/2015

NHTSA · Herstellerbulletin10147699Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

"N14 ENGINE TIMING CHAIN AND TENSIONER: LIMITED WARRANTY EXTENSION TO 7 YEARS/100,000 MILES. INFORMATION As part of a Class Action Suit Settlement for the vehicles listed above (""Class Vehicles""), MINI USA, a division of BMW of North America, LLC, is extending the limited warranty for the engine timing chain and tensioner to: 7 years/100,000 miles as determined by the vehicle's original in-service date This component-specific limited warranty extension applies to: Defects in materials or workmanship; and this Extended coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the MINI New Passenger Car Limited Warranty. For the eligible MINI vehicles, the limited warranty extension applies to the: Timing Chain (1) Timing Chain Tensioner with Seal Ring (4) In conjunction and when necessary, the parts listed below may only be claimed when there replacement is required to ""properly"" perform a covered repair of the timing chain and/or tensioner: Guide Rail (2) Tensioner Rail (3) Timing Chain Tensioner Seal Ring (5) Crankshaft Sprocket (6) Guide Rail (11) Bearing Bolt with Washer (13) Washer (14) Bearing Bolt with O-ring (15) O-ring (16)Note: This bulletin is a notice of a component-specific ""limited warranty extension as part of a Class Action Settlement. This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing a problem with the timing chair and/or tensioner."

NHTSA · Herstellerbulletin10147574Modelljahre 2009Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
BulletinGeringMotorNA

Bulletin

"Technical Service N18 Engine High-Pressure Fuel Pump (HDP): Limited Warranty Extension to 10 Years/120,000 Miles This Service Information bulletin supersedes SI M01 01 16 dated March 2016. INFORMATION For the above-referenced vehicles, MINI USA, a division of BMW of North America, LLC ("MINI USA") is extending the limited warranty for the engine's High-Pressure Fuel Pump (HDP) to: 10 years/120,000 miles as determined by the vehicle's original in-service date. Item #1: This "componentspecific" limited warranty extension applies to defects in materials and workmanship and is subject to the applicable vehicle and coverage eligibility requirements, exclusions and limitations that apply to the New MINI Passenger Car Limited Warranty. Important Note: This limited warranty extension only applies to the listed vehicles produced up to and including 2/29/2012 (Leap year). Vehicles produced on or after 3/1/2012 are fitted with different equipment. Warning: This bulletin is notice of a "limited warranty extension." This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing this problem. Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release."

NHTSA · Herstellerbulletin10146985Modelljahre 2011–2012Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Ältere →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).