Electrical system: problems reported by owners
30 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 2004–2010), typically at around 106,000 miles. Reported consequences: 1 crash, 5 fires.
🔔 Kostenloses Konto anlegen und Benachrichtigungen zu Mitsubishi Endeavor erhalten
Diese Akte sammelt die bekannten Mängel des Mitsubishi Endeavor, verfasst und belegt von der Community. Lesen ist frei; mit einem kostenlosen Konto kannst du beitragen. Ein Mangel erhält das Siegel, sobald genug angesehene Mitwirkende ihn bestätigt haben.
30 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 2004–2010), typically at around 106,000 miles. Reported consequences: 1 crash, 5 fires.
28 owners in the United States reported problems with the engine and cooling of this car to NHTSA (model years 2004–2007), typically at around 63,000 miles. Most often named: cooling system (32%), cooling system:radiator assembly (18%). Reported consequences: 1 crash, 1 fire, 2 injuries.
28 owners in the United States reported problems with the transmission and drivetrain of this car to NHTSA (model years 2004–2008), typically at around 64,000 miles. Most often named: automatic transmission (32%). Reported consequences: 6 crashes.
Issue: On certain vehicles, the compliance label may be missing information in French. The words and abbreviations listed on the label for "TIRES", "RIMS", "WITH", "FR" and "RR" and appear in English only, when they should be listed as "TIRES/PNEUS", "RIMS/JANTES", "WITH/AVEC", "FR/AVT" and "RR/ARR". Canadian regulations require this information to be listed on the label in both English and French. Safety Risk: These small errors do not affect vehicle safety. Corrective Actions: This is not a recall. Mitsubishi has corrected the compliance label for all new vehicles.
Certain vehicles, operated in areas where road salts are frequently used in winter, may be exposed to road debris (mud) mixed with road salt. This material can become trapped between a reinforcing bracket and the fuel filler pipe, potentially causing corrosion. Over time, corrosion could create a leak in the fuel filler pipe that could result in fuel leakage when fueling the vehicle. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will replace the fuel filler pipe of vehicles equipped with the first-generation version. Vehicles assembled with the second-generation filler pipe will be inspected and, if severe corrosion on the fuel filler pipe is observed, the pipe will be replaced with a third-generation version. For vehicles where corrosion of the fuel filler pipe is not observed, an anti-corrosion wax-like material will be applied to the filler pipe, and the inner wheel well shield will be replaced with an updated part that provides improved protection against mud intrusion and accumulation. ** Note: This recall supersedes recall 2010050.**
On certain vehicles, the software programming in the Heating, Ventilation, Air Conditioning (HVAC) controller may allow a combination of numerous data inputs to temporarily overload the calculation capacity of the controller, resulting in incorrect signals to be transmitted to the heater case mode door. This may cause the mode door to move to unselected positions during heater operation until the controller recovers and returns to proper operation. Over time, this excessive movement may damage the mode door shaft. These conditions could affect defroster performance, resulting in delayed clearing of the windshield, which could compromise safe vehicle operation and increase the risk of a crash. Correction: Dealers will replace the HVAC controller assembly, inspect the mode-door shaft for possible damage, and repair the mode-door shaft if necessary.
This Technical Service Bulletin was sent to dealers providing general Pre-Delivery Inspection (PDI) procedures, both technical and detail, for 2023 model year Mitsubishi vehicles (except Outlander PHEV).
This Technical Service Bulletin informs dealers they may find a stain or cloudy spot on the body panels after removing the transportation film.due to improper installation of the film.This TSB instructs the dealers of the repair procedure for removal of the stain.
This Technical Information Notice was sent to dealers informing that MMNA has recently received information from Mitsubishi Motors Corporation (MMC) about the effects of the Waterborne (WB) paint process on Mitsubishi vehicles.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).