Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Porsche 928

1977–1995 · 0 dokumentierte Mängel · 2 Märkte
Modelljahr
RückrufKritischSonstigesJP

その他(その他)

音響機器のオーディオ本体(メーカー:ソニー(株)、型式:XR-5H911,XRー5H912)の配 線基板において、当該基板の製造工程が不適切なため、コンデンサーが損傷しているもの があり、そのままの状態で使用を続けると、当該コンデンサーの端子間が短絡して、スピ ーカーに過大な電流が流れ発熱し、最悪の場合、火災に至るおそれがある。

MLIT · Japan7. Dez. 19991207700Modelljahre 1990–1991Im Original (Japanisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufKritischElektrikJP

その他(その他)

音響機器のオーディオ本体の配線基盤において、当該基盤の製造工程が不適切なため、コ ンデンサが損傷しているものがあり、そのままの状態で使用を続けると、当該コンデンサ の端子間が短絡して、スピーカーに過大な電流が流れ、最悪の場合、火災にいたるおそれ がある。

MLIT · Japan19. Dez. 19971206650Modelljahre 1990–1995Im Original (Japanisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufKritischMotorNA

Fuel System

The fuel gauge sending unit mounting nut may crack and, under certain fuel level and operational conditions, result in fuel tank leakage. Leaking fuel could ignite on the hot exhaust system and result in a vehicle fire. Correction: Mounting nuts will be inspected and replaced as required.

Transport Canada14. Juni 19901990089Modelljahre 1990Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufKritischMotorNA

Engine

The heatshield above the catalytic converter is inadequate under certain circumstances involving engine malfunction. A misfiring engine could overheat the catalytic converter causing materials in the vicinity of the converter, including the automatic transmission fluid lines to ignite resulting in an underbody fire. Correction: 1) replace the heatshiel with a larger improved heatshield. 2) install a heat resistant sleeve on atf lines where necessary. 3) replace plastic atf line mounting bracket in proximity to the catalytic converter with a metal mounting bracket.

Transport Canada28. Juni 19891989091Modelljahre 1985–1987Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufKritischMotorNA

Fuel System

Lack of ozone resistance in the fuel return hoses may cause cracking of the fuel line. This could result in fuel leakage and engine compartment fire. Correction: Fuel return hoses will be replaced.

Transport Canada16. März 19871987033Modelljahre 1987Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufKritischMotorNA

Rückruf

A brazed joint on the metal fuel line may leak and result in a vehicle fire.

Transport Canada18. Feb. 19801980020Modelljahre 1980Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelGetriebeNA

Powertrain

A filler piece with insuffient support was installed in the automatic transmission. This piece can move and inhibit the kickdown function. This could result in an accident during overtaking.

Transport Canada6. Aug. 19921992091Modelljahre 1991Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelGetriebeNA

Power train:Automatic transmission

A plastic filler piece located in the automatic transmission was installed without sufficient support. This filler piece can move because of the hydraulic pressure in the system, and not allow the automatic transmission to kick down to a lower gear.

NHTSA · USA3. Aug. 199292V092000Modelljahre 1991Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelFahrwerkNA

Rückruf

Vehicles were equipped with an engine carrier which has a faulty weld to the support bracket. If the weld were to give way, a break in the engine carrier could develop, resulting in a steering blockage and possible loss of vehicle control.

Transport Canada9. Juli 19851985082Modelljahre 1985Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelMotorNA

Engine and engine cooling:Engine

The engine carrier has a faulty weld to the support bracket eyes. Consequence of defect: The weld could give way and the bracket eye separate from the carrier. With higher mileage accumulation a break in the engine carrier could develop and result in a steering blockage, loss of control with possibly an accident.

NHTSA · USA1. Juli 198585V084000Modelljahre 1985Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelBremsenNA

Rückruf

The front brake hoses may have been incorrectly routed during production.If this occurred,the brake hose could rub against the rim at certain road wheel postions and eventually wear through

Transport Canada22. Juli 19821982063Modelljahre 1982Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelFahrwerkNA

Rückruf

The univesal joint connecting the steering shaft to the steering rack may be improperly positioned. If the vehicle is driven on rough roads for an extended period of time the connection could loosen an cause excessive steering wheel free play.

Transport Canada22. Juli 19821982062Modelljahre 1980Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelBremsenNA

Service brakes, hydraulic:Foundation components:Hoses, lines/piping, and fittings

Due to the improper installation of hydraulic brake hoses, the hose could rub against the rim in certain wheel positions. Brake fluid loss could result, causing a degradation in the performance of the front brake system. This would cause an increase in vehicle stopping distances.

NHTSA · USA12. Mai 198282V049000Modelljahre 1982Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelFahrwerkNA

Steering: Steering wheel/handle bar

On the involved vehicles, the universal joint which connects the steering shaft to the steering rack may have been improperly positioned during assembly. If vehicle is driven on poor roads for an extended period of time, the connection between the steering shaft and universal joint could loosen and cause excessive steering wheel free play.

NHTSA · USA12. Mai 198282V048000Modelljahre 1980Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelFahrwerkNA

Suspension:Front:Shock absorber

Front shock absorbers on some vehicles may have improperly welded mounting eyes. The shock absorber mounting could separate and cause the suspension to collapse if vehicle is driven on rough roads for a long period of time.

NHTSA · USA25. März 198181V040000Modelljahre 1980–1981Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).