Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Porsche 924

1976–1988 · 1 generationen · 2 dokumentierte Mängel · 2 Märkte
Generationen
Alle Generationen9241976–19882829
Modelljahr
MarktAlleNA
RückrufKritischMotorNA

Fuel System

The short section of high pressure fuel hose between the fuel rail and the fuel pressure regulator, which runs alongside the intake manifold, may be subject to hardening. In the event that this line does harden, fuel leaks could develop between the hose and metal pipe fittings. Leaking fuel could ignite on the hot exhaust system and lead to an engine compartment fire. Correction: Fuel hose will be replaced on 924s, 944 and 944 turbo vehicles and the fuel hose and fuel rail will be replaced on 944s vehicles.

Transport Canada4. Apr. 19901990051Modelljahre 1987–1988Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufKritischMotorNA

Fuel system, gasoline:Fuel injection system:Fuel rail

The hose material used in the short section of the high pressure fuel line hose, between the fuel rail and fuel pressure regulator, is subject to hardening, and could cause fuel leaks between the hose and the metal pipe fittings.

NHTSA · USA2. Apr. 199090V061000Modelljahre 1987–1988Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelFahrwerkNA

Rückruf

The rear spring plates (radius arms) on these vehicles may have been improperly tempered by supplier. Improperly hardened spring plates could crack and possibly break . This could affect lateral guidance of the corresponding rear wheel resulting in loss of vehicle control.

Transport Canada9. Okt. 19851985110Modelljahre 1982Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelFahrwerkNA

Suspension:Rear:Springs:Leaf spring assembly

Rear spring plates may not have been tempered and are not of the proper hardness value. Consequence of defect: The plates could crack and/or break, affect lateral guidance of the rear wheel, and result in loss of control of the car which may cause an accident.

NHTSA · USA26. Juli 198585V095000Modelljahre 1982Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelInnenraumNA

Seat belts:Front:Retractor

The rear seat belts do not include emergency-locking or automatic-locking retractors. The belts do not comply with federal motor vehicle safety standard no. 208, "occupant crash protection".

NHTSA · USA26. Okt. 198383V111000Modelljahre 1982Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelInnenraumNA

Rückruf

The bridge for the seat belt locking (inertia retractor) mechanism on one suppliers belts may have been improperly crimped. This condition may result in a non-locking retractor.

Transport Canada28. Sept. 19791979167Modelljahre 1980Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelInnenraumNA

Seat belts:Front:Retractor

The bridge in the seat belt buckle locking mechanism of the front seat belt assembly may have been improperly bent. The buckle may not hold properly and will release, if extreme forces are applied.

NHTSA · USA27. Sept. 197979V222000Modelljahre 1980Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufGeringMotorNA

Rückruf

Vehicles were inadvertently equipped with a 1979 model vehicle emission control information label which contains an incorrect vacuum hose touting diagram. These vehicles do not comply with the labelling requirements of canada motor vehicle safety standard 1101 - emission devices.

Transport Canada6. Mai 19801980070Modelljahre 1980Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).