On certain 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I and 735IL vehicles, the fuel feed hose could harden and "set" over time due to engine compartment temperatures. If this "setting" occurs, it is possible that seepage between the hose and fitting could result because the clamp cannot provide sufficient sealing force to compensate for the hardening of the hose. Fuel seepage, in the presence of an ignition source, could result in an engine compartment fire. Correction: fuel feed hoses and associated clamps will be replaced with ones of a new design.
Transport CanadaMay 30, 19941994096Model years 1989View details →
Feed fuel hoses can harden and "set" over time, allowing a seepage of fuel at the connection between the hose and the engine fitting. The clamp used to hold the hose to the fitting is unable to compensate for the hardening of the feed fuel hose.
NHTSA · United StatesApr 11, 199494V066000Model years 1989View details →
The malfunction or failure of a coolant system component results in significantly increased coolant temperature and a resulting increase in system pressure.
NHTSA · United StatesFeb 1, 199393V015000Model years 1984–1989View details →
On certain 318I, 325I and M3 vehicles, elevated pressure in the cooling system due to overheating could result in cracking of the heater core end piece. Should this happen, coolant could be expelled onto the lower right leg of the driver, possibly resulting in personal injury and/or fogging of the interior surfaces of the windows causing reduced driver vision. Correction: A thermistatic bypass valve will be installed to control coolant temperature in the heater core. Also, a new design radiator cap will be installed to control pressure and provide greater overflow.
Transport CanadaJul 19, 19931993100Model years 1984–1989View details →
On certain 325IX vehicles, the oil dipstick tube attaching bracket may have been bent during the manufacturing process or during scheduled maintenance. This could possibly cause the dipstick to interfere with the throttle bellcrank lever's range of motion and prevent the lever from returning to the idle position after release of the accelerator pedal. Correction: Throttle bellcrank lever will be modified to provide sufficient clearance. Note: Vehicles with manual transmission only.
Transport CanadaApr 6, 19881988049Model years 1988View details →
The oil dipstick tube attaching bracket may have been bent during production or scheduled maintenance, reducing the clearance between the dipstick ring and the throttle bellcrank lever.
NHTSA · United StatesMar 15, 198888V031000Model years 1988View details →
The idle control valve which controls idle speed by varying the amount of intake air that bypasses the throttle plate is subject to backfire into the intake manifold. Such backfire can damage the valve and cause the idle valve plate to remain open. Consequence of defect: This will result in abnormally high idle speed.
NHTSA · United StatesMay 6, 198585V058000Model years 1984View details →
On certain 320I vehicles, crack in the exhaust system between the exhaust pipe and the catalytic converter could result in exhaust emissions which do not comply with CMVSS 1103.
Transport CanadaDec 22, 19831983121Model years 1981–1982View details →
On certain 318I vehicles, improper starting procedure could cause a backfire into the intake manifold and damage internal components of the idle control valve. This could result in abnormally high idle speed and if warnings of increased engine noise level and tachometer reading are not heeded, a vehicle crash could occur.
Transport CanadaJun 6, 19851985072Model years 1984View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).