Motor vehicles - bodywork (occupant protective equipment)
The gas generator in the driver's airbag may burst.
🔔 Create a free account to get email alerts about BMW 3 Series (E46)
The gas generator in the driver's airbag may burst.
The driver's airbag gas generator may malfunction if it has been exposed to high absolute humidity and high temperature fluctuations over the years
The inflator of the driver's airbag may malfunction due to long-term degradation. In this case, if the airbag is deployed in an accident, the internal pressure in the inflator may be too high. The inflator could burst. Metal fragments may cause injury.
Affected vehicles are already included in Safety Recalls within the markets they have previously resided in. The vehicles may be fitted with a driver and/or passenger airbag/s which if deployed may do so with excessive force causing sharp metal fragments to be released this may cause serious injury which could prove fatal to people in the vicinity.
The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants.
For vehicles fitted with a Takata front passenger airbag with a PSPI inflator these vehicles have previously received a like for like replacement front passenger airbag via a previous safety recall campaign.
In het geval dat de passagiersairbag al was vervangen, kan de gasgenerator na enkele jaren alsnog defect raken als gevolg van schommelingen in vochtigheid en temperatuur.
Le propulsif dans l’airbag passager peut se détériorer en raison de fortes variations d’humidité et de température. en cas d’accident dans lequel le coussin gonflable se déploie, cela pourrait entraîner des fragments de l’enveloppe du gonfleur qui se détachent et blessent les occupants du véhicule.
Issue: This recall applies to vehicles that may be equipped with a replacement sport or M-sport steering wheel that has a Takata airbag. Long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the driver-front airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Safety Risk: If the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective Actions: BMW will notify owners by mail and advise you to take your vehicle to a dealership to inspect and, if necessary, replace the driver-front airbag module. To learn if your vehicle is affected by this recall, owners may: • Visit <a href= https://www.bmw.ca/en/ssl/VehicleRecall.html> https://www.bmw.ca/en/ssl/VehicleRecall.html</a> • Contact your preferred or local BMW Retailer • Call BMW Customer Relations Recall Services at 1-855-217-3002
BMW of North America, LLC (BMW) is recalling certain 2006-2011 3 Series Sedan (324i, 325i, 325xi, 328i, 328xi, 330i, 330xi, 335i, 335xi), 2006-2012 3 Series Sportswagon (325xi, 328i, 328xi), and 2009-2011 3 Series Sedan (335d) vehicles. The original steering wheel may have been replaced with a sport or M-sport steering wheel equipped with an inflator that can explode during deployment.
The propellant within the integrated inflator of driver airbags can deteriorate during time. If the airbag deploys, it could result in fragments from the inflator casing injuring the vehicle’s occupants.
The propellant in the passenger airbag can deteriorate due to large variations in humidity and temperature. In the event of an accident in which the airbag deploys, it could result in fragments of the inflator casing detaching and injuring the vehicle's occupants.
블로우바이히터의 생산 품질 불량으로 플라스틱 코팅이 단락 열에 의해 녹아 매우 드문 경우 화재가 발생할 수 있는 가능성에 따른 리콜 (*다만 단락이 발생될 경우 엔진경고등(MIL)이 점등되며 이러한 경우, 냄새 또는 연기를 통해 운전자가 이 사실을 바르게 인지할 수 있음) <*대상차량별 생산일자> BMW 128i: 2008.09.25 BMW 128i: 2008.03.17~2008.07.11 BMW 128i: 2008.02.04~2009.06.23 BMW 128i: 2010.09.03~2012.03.02 BMW 128i: 2010.04.26 BMW 323i: 2009.04.17 BMW 323i: 2006.09.04 BMW 325i: 2004.12.15~2007.01.22 BMW 325i: 2005.05.04~2006.08.17 BMW 325i: 2005.09.15~2006.05.10 BMW 325xi: 2005.11.22~2006.05.23 BMW 325xi: 2005.07.14 BMW 328i: 2011.07.04~2012.11.12 BMW 328i: 2010.10.18~2011.03.14 BMW 328i: 2010.11.18~2012.08.28 BMW 328i: 2011.02.14~2011.09.23 BMW 328i: 2008.09.02~2009.04.30 BMW 328i: 2008.09.16~2008.10.22 BMW 328i: 2009.04.07~2011.07.25 BMW 328i: 2009.02.13~2009.05.21 BMW 328i: 2010.07.08~2011.10.14 BMW 328i: 2009.09.21~2010.10.05 BMW 328i: 2008.08.21~2008.11.13 BMW 328i: 2009.02.16 BMW 328i: 2009.09.24~2011.07.25 BMW 328i: 2009.10.07~2010.09.27 BMW 328i: 2006.08.24~2008.02.20 BMW 328i: 2006.09.02~2008.07.29 BMW 328i: 2006.10.30~2008.06.13 BMW 328i: 2006.09.11~2008.04.03 BMW 328i: 2008.07.02 BMW 328i: 2006.06.26~2009.01.20 BMW 328i: 2007.05.30~2009.07.29 BMW 328i: 2007.03.24~2009.04.27BMW 328i: 2009.10.08~2009.12.01 BMW 328i: 2006.11.15~2009.07.24 BMW 328i: 2009.11.03 BMW 328i Convertible: 2009.12.08~2013.07.24 BMW 328i Convertible: 2006.12.12~2010.01.20 BMW 328i xDrive: 2010.06.18 BMW 328xi: 2009.07.24 BMW 328xi: 2009.09.08~2010.10.08 BMW 328xi: 2011.10.06~2011.12.05 BMW 328xi: 2008.10.31~2009.07.24 BMW 328xi: 2009.10.16~2011.08.02 BMW 328xi: 2008.10.15 BMW 328xi: 2006.10.11~2007.12.12 BMW 328xi: 2006.09.11~2007.09.24 BMW 328xi: 2006.10.23~2009.01.22 BMW 328xi: 2006.09.28~2009.01.28 BMW 328xi: 2009.09.14 BMW 330i: 2004.11.24~2006.07.06 BMW 330i: 2005.03.04~2006.06.14BMW 330xi: 2005.10.26~2006.06.02 BMW 523i: 2005.02.18~2007.02.23 BMW 525i: 2005.03.18~2006.10.04 BMW 525i: 2005.03.07~2006.12.07 BMW 525xi: 2005.07.28~2006.06.26 BMW 528i: 2007.02.21~2009.12.17 BMW 528i: 2007.03.26~2009.01.29 BMW 528i: 2009.07.01~2009.11.26 BMW 528xi: 2007.04.23~2008.11.24 BMW 528xi: 2009.04.14~2009.11.09 BMW 530i: 2005.03.17~2006.12.20 BMW 530i: 2005.03.14~2007.02.22 BMW 530i: 2005.06.17~2006.11.02 BMW 530i: 2007.02.21~2009.09.23 BMW 530xi: 2006.03.08~2006.12.20 BMW 530xi: 2005.07.06 BMW 730i: 2005.03.11~2006.09.21 BMW 730Li: 2005.03.11~2007.03.05 BMW X3 3.0i: 2006.09.05~2007.03.27 BMW X3 3.0i: 2007.07.16~2007.09.07 BMW X3 3.0si: 2007.01.23~2007.04.16 BMW X3 3.0si: 2006.08.29~2009.03.02 BMW X3 3.0si: 2009.09.01~2010.01.13 BMW X5 3.0si: 2007.03.23~2010.02.23 BMW X5 3.0si: 2007.02.10~2009.07.22 BMW X5 3.0si: 2009.12.03~2010.01.21 BMW X5 xDrive30i: 2007.02.02~2008.08.04 BMW X5 xDrive30i: 2009.10.12 BMW xDrive30: 2006.10.11~2009.06.02 BMW xDrive30: 2009.10.01~2009.11.30 BMW Z4 3.0i: 2006.03.01~2008.07.16 BMW Z4 3.0si: 2006.01.11~2007.06.14 BMW Z4 3.0si: 2006.03.10~2006.09.19 BMW Z4 3.0si: 2006.07.25~2008.03.14 BMW Z4 3.0si Coupe: 2006.07.05~2007.06.28 BMW Z4 sDrive: 2010.09.17~2011.06.07 BMW Z4 sDrive30i: 2009.04.22~2011.07.29 ?
The passenger-side airbag inflator may be exposed to moisture if it is subjected to prolonged exposure to extremely high temperature and humidity. As a result, when the airbag deploys, the internal pressure of the inflator may rise abnormally, causing the inflator housing to rupture and fragments to scatter, which could injure occupants.
Due to improper plastic manufacturing of the blow-by heater, irregularities may occur in the insulator of the positive temperature coefficient (PTC) heater element, and over time the PTC heater element may short-circuit, but it is not reliably protected by the fuse. As a result, the PTC heater element may overheat abnormally, melting the outer casing, illuminating the engine warning light, and, in the worst case, leading to a fire.
Issue: On certain vehicles equipped with an N52 or N52K 6-cylinder engine, a manufacturing problem could cause the PCV valve heater (blow-by heater) to short circuit and overheat. Note: This replaces Transport Canada recalls 2017-470 and 2019-170. Only vehicles equipped with an N52 or N52K engine require this repair. Safety Risk: An overheated engine PCV valve heater could create the risk of a fire, even while the vehicle is parked and turned off. Corrective Actions: BMW will notify owners by mail and instruct you to take your vehicle to a dealer to install a wire harness repair kit. BMW recommends that you should park your vehicle outdoors until the recall repairs have been completed.
BMW of North America, LLC (BMW) is recalling certain 2008-2013 1 Series Coupe (128i); 2007-2013 3 Series Coupe (328i, 328xi, 328i xDrive); 2007-2010 X3 SAV (X3 3.0si, X3 xDrive30i); 2008-2013 1 Series Convertible (128i); 2006-2011 3 Series Sedan (325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi); 2006-2012 3 Series Wagon (328i, 328i xDrive); 2007-2013 3 Series Convertible (328i); 2006-2010 5 Series Sedan (525i, 525xi, 528i, 528xi, 530i, 530xi); 2006-2007 5 Series Wagon (530xi); 2007-2010 X5 SAV (X5 3.0si, X5 xDrive30i); 2006-2008 Z4 Coupe (Z4 3.0si); and 2006-2011 Z4 Roadster (Z4 3.0i, Z4 3.0si, Z4 sDrive30i) vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.
運転者席用エアバッグのインフレータ(膨張装置)において、吸湿防止が不適切なため、ガス発生剤が吸湿する可能性がある。そのため、使用過程でガス発生剤が吸湿や乾燥を繰返した場合など、衝突時等のエアバッグ作動時に正常に展開しないおそれがあり、インフレータ内の圧力が上昇して容器が破損することにより、乗員が負傷するおそれがある。
Issue: This recall is for vehicles that had an inspection performed under recall 2019-599, 2019-600 or 2019-601, but where the airbag inflator was not replaced. This new recall will provide replacement of the airbag inflator. On certain cars, exposure to moisture over time could cause the driver-front airbag not to inflate properly in a crash. In some cases, this could cause an airbag not to fully inflate, while in others it could cause it to deploy with more force than normal. It could also cause the inflator to rupture. If the airbag inflator ruptures, small pieces of metal could be propelled toward vehicle occupants or cause damage to the airbag and prevent its proper function. Safety Risk: In a crash requiring an airbag deployment, the driver-front airbag may not inflate properly or the inflator could rupture. This could create a risk of injury. Corrective Actions: BMW will notify owners by mail and instruct you to take your car to a dealer to replace the driver-front airbag inflator.
BMW of North America, LLC (BMW) is recalling certain 2000-2001 BMW 3 Series (323Ci, 325Ci, 328Ci and 330Ci), 1999-2001 323i, 328i, 330i, 330xi, and 2000 323i, 328i stationwagon vehicles equipped with Non-Azide Driver air bag Inflators (NADI) manufactured by Takata. These vehicles are equipped with driver-side air bag inflators that were previously inspected, but not replaced under recall numbers 19V-851, 19V852, or 19V-853. Due to a manufacturing issue, the NADI inflator may absorb moisture, causing the inflator to explode or the air bag cushion to underinflate.
助手席用エアバッグのインフレータ(膨張装置)について、長期間にわたり、著しく高温多湿な環境下にさらされると、当該インフレータに水分が浸入する可能性があり、結果として、エアバッグ展開時にインフレータ内圧が異常上昇し、インフレータ容器が破損して飛び散り、乗員が負傷するおそれがある。
運転者席用エアバッグのインフレータ(膨張装置)において、吸湿防止が不適切なため、ガス発生剤が吸湿する可能性がある。そのため、使用過程でガス発生剤が吸湿や乾燥を繰返した場合など、衝突時等のエアバッグ作動時に正常に展開しないおそれがあり、インフレータ内の圧力が上昇して容器が破損することにより、乗員が負傷するおそれがある。
Issue: This recall is for certain vehicles that had an airbag inflator replaced as a part of an earlier recall campaign. This recall provides a final repair. Long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the passenger-front airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Safety Risk: If the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective Actions: Owners will be notified by mail and instructed to take their vehicle to a dealer to inspect the passenger-front airbag module. The passenger-front airbag module will be replaced as necessary. Note: The Canadian climate results in the propellant degrading slowly. This recall is being conducted as a precaution to address future risk. It is expected that all airbag inflators will be replaced before their function would be affected.
BMW of North America, LLC (BMW) is recalling certain 2000-2005 323iT, 325iT, 325xiT, 320i, 323i, 325i, 325xi, 328i, 330i and 330xi and 2000-2006 323Ci, 325Ci, 328Ci, 330Ci, M3 Coupe, 323Cic, 325Cic, 330Cic, and M3 Convertible vehicles equipped with non-desiccated frontal Takata PSAN inflators and PSPI passenger frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) propellant that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i xDrive and M3, 2009-2011 335D, 2006-2012 325xi, 328i, 328xi and 328i xDrive, 2010-2011 X6 ActiveHybrid, 2007-2013 328i, 335i, 335is, M3 Coupes, X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M, 2009-2013 X5 xDrive35d and 2008-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles equipped with non-desiccated driver frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).