On certain passenger vehicles equipped with 3800 v6 (l36) engines and certain delphi fuel pressure regulators, the regulators have a much higher than usual rate of fuel leaks. A leak can allow fuel to enter the intake manifold through a vacuum line. If the engine does not start when cranked, the fuel from the leaking regulator and a mistimed spark can cause a backfire.
NHTSA · United StatesFeb 24, 200404V090000Model years 1998–2000View details →
Certain passenger, mini vans, and sport utility vehicles have an air bag inflator on the driver's side that could fracture at a weld during a deployment.
NHTSA · United StatesAug 9, 200202V222000Model years 2002–2003View details →
These vehicles may exhibit a backfire during engine starting that can cause breakage of the upper intake manifold. This can cause a no-start condition and possibly an engine compartment fire. Also, if a person was in the vicinity of the intake manifold when the hood was open, and this backfire condition occurred, it could result in personal injury. Correction: The pcm (powertrain control module) will be reflashed with new programming software.
Transport CanadaJul 11, 19961996099Model years 1996–1997View details →
The upper transaxle oil cooler hose could pull out of the crimped coupling at the transaxle end of the line assembly. If this coupling were to separate, transaxle oil would spill into the engine compartment and, in the presence of an ignition source, a fire could occur. Correction: Dealers will install a new upper transaxle oil cooler line on all involved vehicles.
Transport CanadaMar 14, 19941994051Model years 1992–1993View details →
The brake hydraulic unit mounting bolts on these vehicles may have been undertorqued. This condition could cause increased brake pedal travel and/or poor pedal feel if the attachment loosens. In addition, this condition could eventually lead to separation of the brake hydraulic unit from its mounting brackets resulting in brake loss and a possible vehicle crash. Correction: Hydraulic unit mounting bolts will be replaced on involved vehicles.
Transport CanadaApr 19, 19881988056Model years 1987–1988View details →
Under a high resistance load, the in-line fuseable link located in the area of the plastic windshield washer bottle bracket, may melt down and ignite the bracket. This could result in an engine compartment fire without prior warning. Correction: Windshield washer bottle bracket will be replaced on affected vehicles.
Transport CanadaAug 26, 19871987096Model years 1987View details →
Vehicles may have been assembled with a rubber fuel return hose which could allow a slow fuel leak while the engine is running. Under certain conditions this could result in a fire which could spread to the passenger compartment and cause burn unjuries to occupants.
Transport CanadaSep 6, 19841984099Model years 1984View details →
The power brake vacuum hoses may fail to conform to federal motor vehicle safety standard no. 106, "brake hoses". The material used in the hoses will not perform according to specifications. The purpose of this regulation is stated as, "to reduce death and injuries occurring as a result of brake system failure from pressure or vacuum loss due to hose assembly rupture".
NHTSA · United StatesMar 23, 198181V037000Model years 1981View details →
Vehicle description: Passenger vehicles. These vehicles do not conform to the requirements of fmvss no. 108, "lamps, reflective devices, and associated equipment." the head lamp adjustment device horizontal adjuster may not move the head lamp reflector when the shaft is rotated in a normal manner during aiming.
NHTSA · United StatesDec 17, 199999V355000Model years 2000View details →
On certain vehicles, the inner tie rod nuts may be loose, which could result in separation of a tie rod. Separation of a tie rod could cause unexpected steering input in some maneuvers and could cause a crash without prior warning. Correction: Dealers will check the torque of the inner tie rod nuts and if necessary, adjust the vehicle toe-in and tighten the inner tie rod nuts to the specified torque.
Transport CanadaNov 15, 19991999213Model years 2000View details →
Certain vehicles do not comply with the requirements of CMVSS 102 - Transmission Shift Control Sequence. A retaining clip which secures the manual valve to the linkage of the transmission detent lever, may become loose and allow the link to become disconnected from the manual valve. If the link disconnects, the driver's indicated 'PRNDL' state may differ from the hydraulic state of the transmission. This does not affect the 'PARK' position, but if a driver selects 'DRIVE' and the transmission is actually in 'REVERSE', a crash could occur without warning. Correction: Dealers will replace the manual valve/link assembly with a replacement manual valve/link kit, featuring a spring-type fastener.
Transport CanadaMay 6, 19991999080Model years 1999View details →
Vehicle description: Passenger vehicles equipped with 4t65e automatic transmissions. These vehicles fail to conform to the requirements of fmvss no. 102, "transmission shift lever sequence." a retaining clip, which secures the manual valve to the linkage of the transmission detent lever, can become loose under a combination of possible driver shifting maneuvers and allow the link to become disconnected from the manual valve.
NHTSA · United StatesApr 26, 199999V089000Model years 1999View details →
These vehicles do not comply with c.M.V.S.S. 1101 - emission device. Improper calibration of the powertrain control module (pcm) can result in uncontrolled spark knock, setting an mil (malfunction indicator lamp), misfire, rough idle, audible knock and/or possible engine damage. Correction: Vehicle pcm will be reflashed with new calibration softwear.
Transport CanadaFeb 20, 19981998034Model years 1998View details →
Certain vehicles may not comply with CMVSS 209 - Seatbelt Assemblies. Vehicles may have been assembled with one or more incorrect seat belt and/or seat belt buckle ends. If an incorrect part is used, the belt may not latch properly, increasing the risk of injury to the occupant should a vehicle crash occur. Correction: Vehicles will be inspected and incorrect parts replaced.
Transport CanadaMar 7, 19961996045Model years 1997View details →
These vehicles were assembled with one or more incorrect safety belt and/or safety belt buckle ends. This does not conform with the requirements of fmvss no. 209, "seat belt assemblies."
NHTSA · United StatesMar 5, 199696V044000Model years 1997View details →
Vehicle description: Passenger vehicles manufactured from august 1991 through july 1995. The transmission oil cooler line can separate when the vehicle is operated in low temperatures in combination with high transmission loads.
NHTSA · United StatesJan 23, 199696V015000Model years 1992–1993View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).