Service bulletins (TSBs) are repair instructions manufacturers send to their dealers about known problems. They are not safety recalls, but they often confirm a defect.
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
NHTSA · manufacturer bulletin11017016Model years 2012View details →
This Preliminary information is to inform the dealer of a possible coolant leak from an engine expansion plug. The dealer is advised to seal and replace the core plug to correct the leak.
NHTSA · manufacturer bulletin10161015Model years 2007View details →
This Preliminary Information communication provides information to the technician that after installing a re-manufactured High Feature V6 engine the vehicle may rough running, idle surge, Check Engine Lamp or Camshaft Position sensor actuator codes. Technician will need to record the actual engine oil pressure at idle and engine compression readings. Technician will need to perform all testing listed in PIP4345A, if oil pressure and compression readings are within specifications. Technician will need to contact General Motors Technical Assistance Center for further assistance if the concern is not isolated.
NHTSA · manufacturer bulletin10112439Model years 2009View details →
This Preliminary Information communication provides information to the technician that after installing a re-manufactured High Feature V6 engine the vehicle may rough running, idle surge, Check Engine Lamp or Camshaft Position sensor actuator codes. Technician will need to record the actual engine oil pressure at idle and engine compression readings. Technician will need to perform all testing listed in PIP4345A, if oil pressure and compression readings are within specifications. Technician will need to contact General Motors Technical Assistance Center for further assistance if the concern is not isolated.
NHTSA · manufacturer bulletin10112521Model years 2009View details →
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have the Antilock Braking System, Service Traction Control System, and/or Service Stabilitrak lights are on. The Electronic Brake Control Module may have one or more of the following Diagnostic Trouble Codes C0035-C0050 with specifically symptom 18, 5A, or 0F. Technician will gain access to the correct wheel bear per the Diagnostic Trouble Code that is set. If debris is found on the magnetic encoder ring it will needed to be cleaned.
NHTSA · manufacturer bulletin10112074Model years 2011View details →
This preliminary information communication provides information to the technician on how to diagnose and repair vehicles that may have the antilock braking system, service traction control system, and/or service stabilitrak lights are on. The electronic brake control module may have one or more of the following diagnostic trouble codes c0035-c0050 with specifically symptom 18, 5a, or 0f. Technician will gain access to the correct wheel bear per the diagnostic trouble code that is set. If debris is found on the magnetic encoder ring it will needed to be cleaned.
NHTSA · manufacturer bulletin10080901Model years 2011View details →
This preliminary information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for non - general motors aftermarket accessories installed on the vehicle that can cause these issues.
NHTSA · manufacturer bulletin10078874Model years 2012View details →
General motors: Due to the parasitic drain/discharge on 2011 vehicles and trucks, a no crank/no start and dead battery would occur. Cadillac sts and chevrolet volt not included. *pe
NHTSA · manufacturer bulletin10044124Model years 2011View details →
General motors: In rare occurrences a technician may find dtc p0513, an intermittent no crank/no start. This dtc may be caused by a transient voltage spike within the ecm and usually occurs on start up. The ecm must be replaced with one that was not produced in the julian date range. *pe
NHTSA · manufacturer bulletin10030169Model years 2008View details →
General motors: Various electrical concerns (inspect engine harness near brake lines). One or more of following concerns may apply-malfunction indicator lamp/check engine light, antilock brake system indicator. *pe
NHTSA · manufacturer bulletin10028246Model years 2009View details →
Diagnostic trouble code (dtc) c0710 steering wheel position sensor (swps) signal, service stability system message on driver information center (dic). *tt updated 2/15/08. *nj
NHTSA · manufacturer bulletin10019477Model years 2008View details →
This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
NHTSA · manufacturer bulletin11017031Model years 2012View details →
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.
NHTSA · manufacturer bulletin11016942Model years 2012View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).