Fuel system, gasoline:Fuel injection system
A backfire during engine starting can cause breakage of the upper intake manifold.
🔔 Create a free account to get email alerts about Buick Riviera (all generations)
A backfire during engine starting can cause breakage of the upper intake manifold.
The intermediate shaft to steering rack lower coupling pinch bolt may be missing. This could result in shaft disengagement and loss of steering control. Correction: Vehicles will be inspected and, if necessary, a pinch bolt will be installed.
The intermediate shaft to steering rack lower coupling pinch bolt may be missing.
In the event of an accident requiring deployment of the driver's side air bag, the inflator module could separate and the air bag will not inflate as intended. In addition, separation of the inflator module may result in hot gases escaping into the occupant compartment, presenting the possibility of burn injury to vehicle occupants. Correction: The air bag inflator modules will be replaced.
On vehicles with anti-lock brakes (abs), the left front brake line could contact the cruise control servo bracket. Over time, this contact could cause the brake line to wear through resulting in brake fluid leakage and partial brake loss. This would result in increased stopping distances and a possible crash. Correction: The left front brake pipe assembly will be replaced.
On vehicles equipped with anti-lock brakes (abs), one or both abs hydraulic unit mounting bolts may not be properly seated. This could cause increased pedal travel and/or poor pedal feel if the attachment loosens. Also, the abs hydraulic unit could separate from its mounting bracket resulting in loss of brakes and a possible vehicle crash without prior warning. Correction: Abs hydraulic unit mounting bolts will be replaced.
One or both abs hydraulic unit mounting bolts may not be properly seated and could loosen.
Left front brake pipe may contact the cruise control servo bracket.
The power steering pump pressure hose assembly could wear against the transmission governor/speed sensor connector and result in a possible fluid leak. This would cause an eventual loss of power assist as well as provide the potential for an underhood fire without prior warning. Correction: Dealers will replace the power steering pump pressure hose assembly.
Insufficient clearance between the power steering pump pressure hose assembly and the transmission governor/speed sensor connector could cause abrasion of the hose.
Vehicle description: Passenger vehicles. The rear shoulder belt(s) do not retract. A retainer could separate from a rear seat shoulder belt retractor which results in the retractor return spring becoming disengaged.
These vehicles do not comply with c.M.V.S.S 114 - locking system and 208 - seat belt installations. The malfunction alarm, lighting and locking (mall) module may contain a damaged capacitor. If the capacitor is damaged, the "key in the ignition" warning chime and the driver seat belt unbuckled warning chime and indicator lamp may be inoperable. In addition, other chime reminder functions, interior lighting controls, and power door locking functions are also affected. Correction: Dealers will inspect and, if required, replace the mall module.
These vehicles were assembled with a malfunction alarm, lighting and locking (mall) module that can contain a damaged capacitor. If the capacitor is damaged, the "key in the ignition" warning chime and the driver seat belt unbuckled warning chime and indicator lamp may not work. This does not meet the requirements of fmvss no. 114, "theft protection" and fmvss no. 208, "occupant crash protection." in addition, other chime reminder functions, interior lighting controls, and power door locking features are also affected.
On certain toronado trofeo's the front outer shoulder belt web sew stop may become stuck in the retractor. This could make the belt difficult to pull out of the retractor, and some occupants may be unable to fasten the belt. In the event of a crash, unbelted occupants are at a significantly higher risk of injury than those who are belted. Correction: A webbing stop button will be installed on affected vehicles.
The front outer shoulder belt web sew stop can become stuck in the retractor. The belt can be difficult to pull out of the retractor and some occupants may not be able to fasten the belt.
Vehicles do not comply with c.M.V.S.S.105- hydraulic brake systems and c.M.V.S.S.101- control location and identification. The brake system indicator light does not light when the ignition is in the "on" position, the parking brake applied, and the shift selector in the (p) park or (n) neutral gear range position. Correction: The programmable read only memory (prom) in the body computer module (bcm) will be replaced.
Brake indicator light may not light when ignition is in the "on" position, the parking brake is applied, and the shift selector is in the park or neutral gear range.
The transmission shift control cable may disengage from the floor control assembly resulting in loss of indicator reference and shift operation. This could result in the transmission not being in the gear indicated by the selector thereby allowing the vehicle to roll away if parked on an incline or to proceed in a direction opposite to the one selected. Correction: Transmission shift control cable retaining clip will be installed on suspect vehicles.
Transaxle shift control cable may disengage from the from the floor shift control with loss of gear indicator reference and shift selector operation.
Misaligned rear seat safety belt shoulder retractor assemblies could cause pendulum interference, causing the belt to remain in locked position or to travel freely without locking.
A misaligned rear seat shoulder belt retractor assembly may result in pendulum interference causing the belt to remain in the locked position or to travel freely without locking. A non-locking shoulder belt retractor could increase the likelihood of injury to a seat occupant in the event of a sudden stop or vehicle crash. Correction: Dealers will inspect and, if necessary, realign thr rear shoulder belt retractor assembly.
A small nylon bushing in the cruise control servo bail (bracket) may slip out of place resulting in possible intermittent increases in engine speed or dieseling. This condition could also cause the servo rod assembly to wear through the ball and catch on other components possibly resulting in a stuck throttle. This could result in loss of vehicle control and a possible crash. Correction: A bushing kit will be installed on the cruise control servo bail.
A small nylon bushing in the cruise control servo bail may slip out of place, causing intermittent and unexpected increases in engine speed or dieseling (engine run on with ignition off).
These vehicles do not comply with c.M.V.S.S. 1105-evaporative emissions. Vehicles may experience an inoperative canister purge thermo vacuum switch.
These vehicles do not comply with c.M.V.S.S. 1105 - evaporative emissions. Vehicles may experience an inoperative canister purge thermo vacuum switch. Correction: Canister purge thermo vacuum switch will be replaced.
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).