These vehicles may not comply with c.M.V.S.S. 301 - fuel system integrity. Some welds in the left rear quarter panel may have been missed during assembly. In the event of a vehicle crash, the vehicle sheet metal structure may not perform as designed. This could result in unexpected damage to the fuel tank or fuel lines and leakage of fuel. If there is a fuel leak and an ignition source, a fire could occur. Correction: Dealers will inspect for missing welds and, if necessary, place three welds between the involved panels.
Transport CanadaOct 30, 19961996173Model years 1997View details →
During assembly of the left rear quarter panel, some welds were missed. This does not comply with the requirements of fmvss no. 301, "fuel system integrity."
NHTSA · United StatesOct 30, 199696V212000Model years 1997View details →
These vehicles were constructed with welds in the rear compartment pan assembly that are not sufficient to comply with the requirements pertaining to fuel tank leakage in the event of a rear impact collision. The fuel tank assemblies do not comply with fmvss no. 301, "fuel system integrity."
NHTSA · United StatesJul 1, 199494V122000Model years 1994View details →
Front fuel feed hose assembly could crack or separate at the coupling on the engine end of the hose assembly, allowing fuel to leak into the engine compartment.
NHTSA · United StatesOct 19, 199292V150000Model years 1988–1989View details →
Vehicles may have improperly torqued connections of the front fuel feed/return hoses to the fuel pipes at the body rail. A fitting may loosen enough to leak fuel into the underhood area, and, in the presence of an ignition source, a fire could result. Correction: Front fuel feed/return hose fittings will be properly torqued.
Transport CanadaJun 11, 19901990083Model years 1990View details →
On vehicles with quad 4 engines, the front fuel feed assembly could crack or separate at the coupling on the engine end of the assembly, allowing fuel to leak into the underhood area. This would create the possibility of an engine compartment fire. Correction: Front fuel feed hose assembly will be replaced on affected vehicles.
Transport CanadaMar 7, 19901990043Model years 1988–1989View details →
Front fuel feed hose assembly could crack or separate at the coupling on the engine end of the hose assembly, allowing fuel to leak into the engine compartment.
NHTSA · United StatesMar 5, 199090V042000Model years 1988–1989View details →
The fuel system may leak at the throttle body injection fuel feed pipe connection. Consequence of defect: This leakage could result in an underhood fire which could spread to the passenger compartment and cause burn injuries to occupants.
NHTSA · United StatesMar 29, 198585V034000Model years 1984View details →
Under certaain conditions, the hose clamps on the fuel tank filler pipe and fuel tank filler vent pipe could fracture. The fracture of these clamps could cause fuel leakage at any of the four pipe to hose connections. Leakage can occur during refueling, or while driving, if the fuel tank is above 3/4 full.
NHTSA · United StatesMar 8, 198282V021000Model years 1982View details →
These vehicles do not comply with c.M.V.S.S. 301 - fuel system integrity. Rear compartment pan welds may not meet manufacturing standards. Correction: Dealers are to install rivets adjacent to the locations where suspect welds may have occurred.
Transport CanadaJul 20, 19941994117Model years 1994View details →
The vehicles were assembled with an incorrect suspension upper spring seat at the right-rear position. If the vehicle is involved in a rear impact accident, the right-hand rear wheel house flange could sever the fuel tank filler pipe and spill fuel.
NHTSA · United StatesJul 17, 199292V106000Model years 1992View details →
Note: Vehicles equipped with 2.3 litre engine. In sub zero temperatures, moisture from the crankcase ventilation system could cause ice buildup behind the throttle blade thereby preventing the throttle from returning to idle when the accerator pedal is released. This could result in loss of vehicle control. Correction: An engine ventilation kit will be installed on affected vehicles to prevent moisture accumulation in the crankcase.
Transport CanadaDec 12, 19911991174Model years 1988View details →
Certain vehicles may not comply with CMVSS 1103 - Exhaust Emissions. Cracks may develop in the casing of the integrated direct ignition coil. Correction: Ignition coils will be inspected and replaced if necessary.
Transport CanadaMar 5, 19911991037Model years 1988–1990View details →
These vehicles do not comply with c.M.V.S.S. 1103 - exhaust emissions. - mass airflow sensor failure - note : Vehicles with 3.0 litre and 3.8 litre engines.
Transport CanadaJan 27, 19871987007Model years 1987View details →
Fuel hoses may be incorrectly positioned and contact the right front drive axle boot during vehicle operation. After a period of time, the rotating boot could wear a hole in the fuel hose, resulting in fule leakage.
NHTSA · United StatesApr 5, 197979V091000Model years 1980View details →
These vehicles do not comply with c.M.V.S.S. 1101 - emission device. Unilingual unleaded fuel label.
Transport CanadaSep 29, 19891989139Model years 1989View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).