On certain passenger vehicles. If the engine fails to start and the driver holds the key in the "start" position for an extended period, high current flows through the ignition switch, and sometimes produces enough heat to melt internal switch parts.
NHTSA · United StatesJan 27, 200404V036000Model years 1998View details →
Certain vehicles, after being exposed to substantial amounts of water, may experience deployment of either the driver or passenger front airbag without a crash. The owner’s manual for these vehicles does not provide specific information about this situation. Inadvertent deployment of the driver and / or passenger front airbag in a non-accident (non-impact) situation may cause damage to the surrounding vehicle environment (windshield / instrument panel), and create expensive vehicle repair, including replacement of the airbag module(s) and the Sensing and Diagnostic Module (SDM). In some instances, inadvertent deployment could cause minor injuries to vehicle occupants. Correction: GM will notify the owners of these 1996 and 1997 vehicles of the potential affect of water accumulating in the vehicle interior on the function of the airbag system (as included in the owner's manuals of 1998 and later model years vehicles).
Transport CanadaJun 24, 20032003162Model years 1996–1997View details →
On certain passenger vehicles. If the engine fails to start and the driver holds the key in the "start" position for an extended period, high current flows through the ignition switch, and sometimes produces enough heat to melt internal switch parts.
NHTSA · United StatesMar 6, 200202V070000Model years 1996–1997View details →
Vehicle description: Passenger vehicles. If the engine starter fails to engage and the driver hold the key in the "start" position for an extended period, high current flows through the ignition switch, producing heat that can melt switch parts.
NHTSA · United StatesOct 2, 200000V287000Model years 1994–1995View details →
The protective cover for the underhood fuse centre may have been omitted on these vehicles. Without this cover, the positive terminal bolt on the fuse block is exposed, and may come in contact with the insulated negative battery cable. Prolonged contact may result in abrasion of the negative cable insulation and could cause an extremely high current short circuit between the positive terminal and the negative cable. This current flow could cause arcing and result in an underhood fire. Correction: A protective cover will be installed if necessary.
Transport CanadaApr 14, 19971997078Model years 1997View details →
The protective cover for the underhood fuse center was omitted. Without this cover, the positive terminal bolt on the fuse block is exposed and can contact the insulated negative battery cable. If the insulation on the negative cable becomes sufficiently worn, an electrical short circuit can occur between the positive terminal and negative cable resulting in extremely high current flow.
NHTSA · United StatesApr 8, 199797V059000Model years 1997View details →
The steering column lower pinch bolt may not have been torqued to specification. This could result in rattle and looseness in the steering system. If the pinch bolt were backed out of the joint completely, rotation of the steering shaft against the connector in high effort steering maneuvers could cause increasing looseness in the steering system and could result in loss of steering and a crash. Correction: Steering column pinch bolt will be inspected and if necessary tightened to specified torque.
Transport CanadaDec 13, 19961996206Model years 1996View details →
These vehicles may not comply with c.M.V.S.S. 301 - fuel system integrity. Some welds in the left rear quarter panel may have been missed during assembly. In the event of a vehicle crash, the vehicle sheet metal structure may not perform as designed. This could result in unexpected damage to the fuel tank or fuel lines and leakage of fuel. If there is a fuel leak and an ignition source, a fire could occur. Correction: Dealers will inspect for missing welds and, if necessary, place three welds between the involved panels.
Transport CanadaOct 30, 19961996173Model years 1997View details →
During assembly of the left rear quarter panel, some welds were missed. This does not comply with the requirements of fmvss no. 301, "fuel system integrity."
NHTSA · United StatesOct 30, 199696V212000Model years 1997View details →
These vehicles were constructed with welds in the rear compartment pan assembly that are not sufficient to comply with the requirements pertaining to fuel tank leakage in the event of a rear impact collision. The fuel tank assemblies do not comply with fmvss no. 301, "fuel system integrity."
NHTSA · United StatesJul 1, 199494V122000Model years 1994View details →
Front fuel feed hose assembly could crack or separate at the coupling on the engine end of the hose assembly, allowing fuel to leak into the engine compartment.
NHTSA · United StatesOct 19, 199292V150000Model years 1988–1989View details →
Moisture can enter the express-down electronic control module and cause a short circuit that causes window operation without operator control, and leaves the window in the down position.
NHTSA · United StatesApr 1, 199292V043000Model years 1991View details →
On vehicles with power windows, moisture may enter the express-down electronic control module and could cause phantom window operation in which the window may cycle without operator input and sometimes remain down. The module may eventually fail by overheating, which could result in a fire in the door panel. Correction: Dealers will replace the power window express-down electronic control module.
Transport CanadaMar 24, 19921992032Model years 1991View details →
The daytime running light (drl) module, which is located near the battery, could overheat and possibly result in an underhood fire. Correction: Dealers will replace the drl module, install a wiring harness with fuses and install a module cover.
Transport CanadaAug 20, 19901990126Model years 1990View details →
Vehicles may have improperly torqued connections of the front fuel feed/return hoses to the fuel pipes at the body rail. A fitting may loosen enough to leak fuel into the underhood area, and, in the presence of an ignition source, a fire could result. Correction: Front fuel feed/return hose fittings will be properly torqued.
Transport CanadaJun 11, 19901990083Model years 1990View details →
On vehicles with quad 4 engines, the front fuel feed assembly could crack or separate at the coupling on the engine end of the assembly, allowing fuel to leak into the underhood area. This would create the possibility of an engine compartment fire. Correction: Front fuel feed hose assembly will be replaced on affected vehicles.
Transport CanadaMar 7, 19901990043Model years 1988–1989View details →
Front fuel feed hose assembly could crack or separate at the coupling on the engine end of the hose assembly, allowing fuel to leak into the engine compartment.
NHTSA · United StatesMar 5, 199090V042000Model years 1988–1989View details →
On vehicles with 2.5l engines. The fuel system may leak at the throttle body injection fuel feed pipe connection presenting the possibility of an underhood fire.
Transport CanadaMar 29, 19851985032Model years 1984View details →
The fuel system may leak at the throttle body injection fuel feed pipe connection. Consequence of defect: This leakage could result in an underhood fire which could spread to the passenger compartment and cause burn injuries to occupants.
NHTSA · United StatesMar 29, 198585V034000Model years 1984View details →
The rear control arm bracket attaching bolts used on certain of these vehicles may fracture. Failure of all four bolts on one side can result in the control arm dropping enough to cut the rear brake hose. Such a cut would result in fluid loss and partial loss of braking action. This would cause increased stopping distances and should a failure occur while trhe vehicle is in motion at a time when minimal stopping distances are required, a vehicle crash could result.
Transport CanadaNov 28, 19841984151Model years 1984View details →
The rear axle control arm locates and helps control axle movement; it attaches to the frame with a bracket. The rear control arm bracket attaching bolts used on some of the involved vehicles may fracture. Fracture of all four bolts on one side of the vehicle can result in the control arm dropping enough to cut the rear brake hose. A severed brake hose would result in brake fluid loss and partial loss of braking ability.
NHTSA · United StatesNov 28, 198484V153000Model years 1984View details →
The brake proportioner valves may break and separate from the master cylinder during braking. This will result in a loss of brake fluid and a partial loss of braking action
Transport CanadaOct 7, 19841983084Model years 1983View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).