Steering:Hydraulic power assist:Hose, piping, and connections
On certain passenger vehicles equipped with 2.4 liter engines, the high pressure power steering hose may prematurely heat age and develop a leak.
🔔 Create a free account to get email alerts about Chrysler Cirrus (all generations)
On certain passenger vehicles equipped with 2.4 liter engines, the high pressure power steering hose may prematurely heat age and develop a leak.
Vehicle description: Passenger vehicles. Some of these vehicles may have been built with an inadequate weld between the right front brake hose block and the stand-off bracket.
Vehicle description: Passenger vehicles. The rear seat belt anchor does not achieve the loading required by fmvss no. 210, "seat belt assembly anchorages."
Vehicle description: Passenger vehicles. The lower control arm ball joint can separate due to loss of lubrication.
In certain vehicles, the engine cylinder head oil galley plug does not seal properly and engine cylinder head oil is not adequately retained.
An engine cylinder head oil galley plug may not be adequately retained. Inadequate retention of the plug may result in oil leakage which could potentially cause a fire in the engine compartment. Correction: An expansion plug and retaining bracket will be installed over the suspect cylinder head oil galley plug.
On certain passenger vehicles, the floor shifter ignition-park interlock may fail and allow the shifter to be moved out of the park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position.
Vehicle description: Passenger vehicles. The right rear brake tube can contact the exhaust system clamp and wear a hole in it.
On certain vehicles, incorrect weld wire, in combination with the stainless steel shell of the catalytic converter, will cause rusting at the weld joints and premature failure to the converter assembly. Correction: Dealers will replace the catalytic converter.
Note: Vehicles equipped with a floor mounted automatic transmission shift lever. A combination of applying a mis-adjusted shifter release button with a low force attempt to shift out of park with the key in the locked position may break the connecting pin in the shifter. If this happens, the "ignition-park" interlock system will not function. Correction: The console shift interlock mechanism will be inspected for proper function. Any vehicles that are not functional after the inspection will have the shift mechanism and cable replaced with a current production "self adjusting" design.
Vehicle description: Passenger vehicles equipped with automatic transmissions. The adjustment of the cable connecting the console shifter mechanism to the ignition key can cause a trapped key condition which can result in a low force required to depress the shift button. A combination of applying a mis-adjusted release button with a low force attempt to shift out of park with the key in the locked position, can break the connecting pin in the shifter.
These vehicles may not comply with c.M.V.S.S. 210 - seat belt assembly anchorages. The rear seat belt anchor may not achieve the loading required by the standard during testing. Correction: The rear outboard seat belt anchor floor attachments will be inspected for orientation and repositioned if required.
Certain vehicles do not comply with CMVSS 1103 - exhaust emissions. The calibration of the Powertrain Control Module (PCM) may fail to adequately control CO emissions. Correction: PCM will be reflashed with a new calibration.
On certain vehicles, the lower control arm ball joint may separate due to loss of lubrication. This separation could result in loss of vehicle control and a crash without prior warning. Correction: Ball joint end housing cover seal will be inspected for leakage and the rubber boot will be inspected for damage. If the cover seal leaks or the boot is damaged, the lower control arm will be replaced.
The primary/secondary hood latch spring may not remain in position during hood closing, which can result in loss of both the primary and secondary latch function. Loss of hood function can result in a hood fly-up condition. Correction: The secondary hood latch spring will be replaced with one having a longer end hook.
Vehicle description: Passenger vehicles. The secondary hood latch spring can disengage from its retention hole if the hood is slammed shut.
On certain vehicles, the brake master cylinder may leak brake fluid due to a damaged double lip rear piston seal. Brake fluid leakage may result in diminished effectiveness of one portion of the split brake system. Correction: Rear brake master cylinder piston assemblies will be replaced.
Corrosion of the abs hydraulic control unit may cause the solenoid valves to stick in the open position. If either front wheel valve sticks, the vehicle may tend to deviate from a straight stop when the brakes are applied. Correction: A plate will be installed on the abs hydraulic control unit and silicone grease injected into the solenoid cavity to eliminate the potential for this condition.
The brake master cylinder can leak brake fluid due to a damaged double lip rear piston seal.
Corrosion of the abs hydraulic control unit can cause the solenoid valves to stick in the open position.
Vehicle description: Certain passenger vehicles, pickup trucks and sport utility vehicles fail to comply with the requirements of fmvss no. 225, "child restraint anchorage systems." some of the owner's manuals for these vehicles are missing instructions that provide a step-by-step procedure, including diagrams, for properly attaching a child restraint system's tether strap to the tether anchorage.
Vehicle description: Passenger vehicles. The affected vehicles were built with unpainted fuel tank straps.
Vehicle description: Passenger vehicles. The affected vehicles were built with incorrect child lock instruction labels.
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).