Steering: Steering wheel/handle bar
The zinc plating operation performed on the upper steering column shaft coupling bolt caused hydrogen embrittlement and breakage of the bolt.
🔔 Create a free account to get email alerts about Chrysler LeBaron (all generations)
The zinc plating operation performed on the upper steering column shaft coupling bolt caused hydrogen embrittlement and breakage of the bolt.
A steering column coupling bolt may fracture due to hydrogen embrittlement, causing loss of clamping load on the steering column shaft coupling with resultant loss of steering control. Correction: Zinc plated steering column coupling bolts will be replaced with a phosphate coated bolt.
Air bag inflator modules may not contain diffuser holes between the ignitor and propellant chambers.
The engine valve cover gasket may dislocate and allow an engine oil leak at the gasket.
On vehicles with 2.2 litre or 2.5 litre efi(non-turbo) engine, the valve cover gasket may leak oil creating the potential for an engine compartment fire. Correction: Valve cover gasket will be replaced with a revised cover and rtv sealant applied in place of the gasket.
Fuel leakage may occur in low ambient temperature operation at connections of an engine compartment fuel supply hose to the pressure regulator and to the fuel rail.
A resister in the instrument cluster may be subjected to an electrical current overload due to failure of a switching transister.The overheated resister could possibly start a fire in the instrument panel.
A resistor in the electronic panel cluster may be subjected to an electrical current overload due to failure of a switching transistor. Consequence of defect: The overheated resistor could ignite and start an instrument panel fire.
On certain vehicles equipped with a 2.2 Litre turbo engine, an inadequately tightened fuel hose clamp at the fuel system pressure regulator could result in fuel leakage and provide the potential for an engine compartment fire.
An engine compartment fuel hose routed to the fuel system pressure regulator may have an inadequately tightened hose clamp. Consequence of defect: The fuel hose could leak and result in an engine compartment fire.
The potential for fuel leakage exists in the engine compartment at the fuel reservoir seam and its hose connections. The fuel reservoir is a silver colored can mounted to the air cleaner.
On certain vehicles, hydraulic brake tube may interfere with exhaust system hangar bolt and eventually result in brake fluid leakage. This could create a partial loss of braking capability. Should this occur the brake warning light on the instrument panel will warn driver.
Hydraulic brake tube routing to the rear wheels may alloow interference between the tube and the rear park brake cable. Resulting abrasion could cause tube failure and partial loss of braking capability. The instrument panel light will provide warning of the partial loss.
These vehicles may not comply with c.M.V.S.S 207 - anchorage of seats. The travelling seat buckle lock bars (seat belt anchors) on some vehicles equipped with bucket seats may have inadequate strength and may not meet the static load requirements of the standard. Correction: Lock bar assemblies will be replaced.
An improperly adjusted hood latch assembly could prevent engagement of the secondary latching mechanism. In such a case the secondary latch would not function to restrain the hood in the event that the primary latch was not engaged for any reason and hood fly-up could occur, blocking the driver's vision. Correction: Secondary hood latch will be inspected and adjusted if necessary, to ensure proper engagement.
The hood latch assembly may not have been properly installed and the secondary hood latch may be prevented from engaging when the hood is closed.
In areas of high road salt use, vehicles may experience a bonded disc brake pad separation from the front or rear brake plates. This could cause a reduction in brake performance and a possible vehicle crash. Correction: Bonded disc brake linings will be replaced on affected vehicles.
The bonded disc brake linings may separate from the shoes due to a bonding deficiency which may allow corrosion degradation of the bond attachment.
Parking brake cables may be mismatched in length resulting in reduced parking brake application on one wheel and so may not comply with c.M.V.S.S. 105-hydraulic brake systems. Correction: Vehicles will be inspected and those with mismatched cables will have the longer cable replaced with a shorter version.
On vehicles with a 50/50 bench seat, the front outboard passenger seat belt may become difficult to latch and/ or unlatch due to a belt webbing stiffener which could enter the buckle housing and dislodge the buckle latch guide. This could also result in partial latch engagement. Correction: Buckle assembly will be replaced with a revised version if necessary.
Front outboard safety belt may become difficult to latch and or unlatch due to a webbing stiffener entering the buckle housing and dislodging the buckle latch guide.
Mismatched parking brake cable lengths to the rear wheels reduces braking ability of one of the rear wheels, in violation of fmvss 105.
Note: Vehicles located in ontario, quebec, new brunswick, nova scotia, prince edward island and newfoundland. These vehicles may not comply with c.M.V.S.S. 108 - lighting due to corrosion failure of the daytime running light module. Correction: Drl module will be replaced with one having additional potting material that covers all previously exposed components.
The two air bag system front impact sensors may not be secured to their mounting brackets.
The front disc caliper guide bolts may not have been torqued adequately. This could create the potential for some degree of abnormal brake function. Correction: Front brake caliper guide pin bolts will be tightened to specified torque.
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).