Engine and engine cooling:Engine
The engine valve cover gasket may dislocate and allow an engine oil leak at the gasket.
🔔 Create a free account to get email alerts about Dodge Aries (all generations)
The engine valve cover gasket may dislocate and allow an engine oil leak at the gasket.
On vehicles with 2.2 litre or 2.5 litre efi(non-turbo) engine, the valve cover gasket may leak oil creating the potential for an engine compartment fire. Correction: Valve cover gasket will be replaced with a revised cover and rtv sealant applied in place of the gasket.
Vehicles equipped with 2.2 litre propane fuelled engines may experience corrosion of the fill and outage (80% fill level) fittings at the fill valve. In the presence of an ignition source, a fire or explosion could result. Correction: Suspect vehicles will have the fill and outage hoses replaced, an improved shield and rustproofing applied to the fittings.
Note: These vehicles were sold to bell, d.N.D., and r.C.M.P. These vehicles were built with a fuel hose which may have had its fittings aligned in a manner which could cause abrasion damage due to engine rocking and result in a fuel leak, thereby creating the risk of fire.
The potential for fuel leakage exists in the engine compartment at the fuel reservoir seam and its hose connections. The fuel reservoir is a silver colored can mounted to the air cleaner.
On certain vehicles, hydraulic brake tube may interfere with exhaust system hangar bolt and eventually result in brake fluid leakage. This could create a partial loss of braking capability. Should this occur the brake warning light on the instrument panel will warn driver.
Hydraulic brake tube routing to the rear wheels may alloow interference between the tube and the rear park brake cable. Resulting abrasion could cause tube failure and partial loss of braking capability. The instrument panel light will provide warning of the partial loss.
Brake fluid may contain an excessive amount of water. This can cause degradation of braking performance or brake failure under a variety of circumstances.
Front suspension crossmember may corrode and fail at lower control arm rear pivot mounts if operated where salt is used to aid in snow removal.
On certain vehicles, the crossmember can become abnormally corroded at the lower control arm attachment. This could result in lower control arm separation and loss of vehicle control. Correction: crossmembers will be inspected and replaced if corrosion is excessive. Remainder will have crossmember retaining brackets installed.
These vehicles do not comply with c.M.V.S.S. 1103 - exhaust emissions. Plugged choke vacuum delay valve. Note: Vehicles equipped with 2.2 litre carbureted engines.
Battery cap vents may be partially or completely blocked with plastic flashing. Consequence of defect: A build up of internal gas pressure could occur which could result in case rupture, particularly during post charging. Should a person be in the vicinity of the battery when the case ruptures, they may be injured by the released gases and/or acid.
These vehicles may not comply with cmvss 1103 - exhaust emissions.
These vehicles may not comply with cmvss 1103 - exhaust emissions.
Location of hydraulic brake tube to both rear wheels causes interference and chafing between the tubes and rear suspension trailing arm pivot brackets.
Hydraulic brake tubing routed to the left rear wheel brake system may have been bent out of shape during assembly and could chafe against the exhaust system hanger bolt.
On the involved vehicles, improper routing of the hydraulic brake tube could cause it to chafe against the park brake cables. Eventually, the brake tube may fail and brake fluid leakage may occur.
The brake hydraulic system bay be equipped with brake fluid containing an excess of water.
Involved vehicles may have been built with improperly forged or heat treated bolts used to attach the front suspension ball joints to the steering knuckles. Some of the bolts may eventually fail which could result in ball joint separation and affect vehicle directional controllability.
Clamp bolts installed on certain vehicles may contain cracks. Eventually these bolts may break through, causing separation of the ball joint from the steering knuckle.
The automatic speed control switch may stick in the "resume" position restricting return movement. This will not allow the normal brake pedal operation to deactivate the system.
The stop lamp switches installed on the subject vehicles may have inadequate internal switch contact pressure due to an incorrect formation of the switch contact terminals. This lack of switch contact continuity may render the (stop) brake warning lights inoperative.
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).