Steering: Steering wheel/handle bar
The zinc plating operation performed on the upper steering column shaft coupling bolt caused hydrogen embrittlement and breakage of the bolt.
🔔 Create a free account to get email alerts about Dodge Daytona (all generations)
The zinc plating operation performed on the upper steering column shaft coupling bolt caused hydrogen embrittlement and breakage of the bolt.
Air bag inflator modules may not contain diffuser holes between the ignitor and propellant chambers.
The engine valve cover gasket may dislocate and allow an engine oil leak at the gasket.
Fuel leakage may occur in low ambient temperature operation at connections of an engine compartment fuel supply hose to the pressure regulator and to the fuel rail.
On certain vehicles equipped with a 2.2 Litre turbo engine, an inadequately tightened fuel hose clamp at the fuel system pressure regulator could result in fuel leakage and provide the potential for an engine compartment fire.
An engine compartment fuel hose routed to the fuel system pressure regulator may have an inadequately tightened hose clamp. Consequence of defect: The fuel hose could leak and result in an engine compartment fire.
Inadequate weld attachment of the front frame rails to the dash panel may result in cracking of the dash panel around the shock tower and floor pan area. This may compromise the vehicle's impact protection capability. Correction: Dash panel will be secured to the frame rails by adding additional fasteners (nuts and bolts).
The welding attachments of the front frame rails to the floor pan sheet metal may not be properly welded.
The bonded disc brake linings may separate from the shoes due to a bonding deficiency which may allow corrosion degradation of the bond attachment.
Mismatched parking brake cable lengths to the rear wheels reduces braking ability of one of the rear wheels, in violation of fmvss 105.
Front disc brake caliper guide pin bolts may not have been adequately torqued and could loosen.
On vehicles with power adjusted bucket seats, the driver's seat frame may fail at one of its four attachments. This can result in fore/aft or lateral movement of the seat. This could cause loss of vehicle control and a possible vehicle crash. Correction: The driver's seat frame will be replaced with a strengthened version. Also, the power adjuster crossmember will be reinforced.
Drivers seat frame may experience fatigue failure at one (front/outboard) of its four attachments.
These vehicles do not comply with c.M.V.S.S. 1103 - exhaust emissions. Plugged choke vacuum delay valve. Note: Vehicles equipped with 2.2 litre carbureted engines.
Battery cap vents may be partially or completely blocked with plastic flashing. Consequence of defect: A build up of internal gas pressure could occur which could result in case rupture, particularly during post charging. Should a person be in the vicinity of the battery when the case ruptures, they may be injured by the released gases and/or acid.
Vehicles may have been built with a potential for the separation of the hood panel from the latch system mechanism. An improper assembly plant repair procedure may have resulted in inadequate structural integrity of the hood latch system attachment to the hood panel. Under certain driving conditions this could result in hood fly-up.
Some hood latch assemblies may have been improperly repaired at the factory, or incorrect fasteners were used. Hood latch attachment will not be strong enough and will likely weaken the inner hood panel.
The owner's manual incorrectly states that the front passenger door cannot be opened from the inside if the door is locked until the lock control handle has been pulled up. On these vehicles, the front passenger door can be opened by the inside door handle even if the door is locked.
Certain Daytona and Daytona Shelby vehicles do not comply with CMVSS 110 - tire selection and rims. (incorrect tire placard)
Incorrect tire pressure placard was installed on cars; does not comply with fmvss 110.
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).