Vehicle description: Passenger vehicles. Starter assemblies were built with suspect plastic terminal blocks which could develop stress cracks subsequent to their installation onto the body of the starter. Separation of the terminal block from the starter body could potentially allow the un-fused positive terminal to come into contact with an adjacent surface, providing a path to ground.
NHTSA · United StatesDec 12, 200000V416000Model years 2001View details →
The steering column coupler may become disconnected when the vehicle experiences a severe impact to the undercarriage. This would result in loss of steering control. Correction: Steering column coupler will be replaced with one that collapses on impact.
Transport CanadaOct 8, 19971997171Model years 1995View details →
The fuel and rear brake tubes may experience accelerated corrosion between the tubes and a rubber isolator. Failure of these tubes could result in fuel leakage and/or diminished braking capacity. Correction: Brake, fuel supply and fuel vapour tubes will be inspected for the presence of red corrosion. Any tubes showing evidence of red corrosion will be replaced. In addition vehicles will have the rubber isolator replaced with a plastic clip.
Transport CanadaNov 20, 19961996186Model years 1995View details →
Vehicle description: Passenger vehicles. In the presence of oil and heat, the brake booster vacuum hose could swell and loosen from the intake manifold.
NHTSA · United StatesMay 8, 200101V154000Model years 2000–2001View details →
Vehicle description: Passenger cars. Vapors from the positive crankcase ventilation (pcv) system can condense and freeze inside of the throttle body when the vehicle is operated in extremely cold ambient temperatures.
NHTSA · United StatesJul 17, 200000V194000Model years 2000View details →
These vehicles do not comply with c.M.V.S.S. 1103 - exhaust emissions. The solid state fan relay could fail because of heat related electrical over stress causing the fan(s) to stop and the vehicle to overheat. Both emissions and driveability may be impacted if the vehicle overheats. Correction: The solid state relay will be replaced and a diode jumper wire will be installed in the fan wiring circuit.
Transport CanadaMar 27, 19981998053Model years 1997–1998View details →
The circuit design in the air bag electronic control module may allow the potential for inadvertent air bag deployment upon vehicle ignition shut down. Correction: The air bag electronic control module will be replaced with a module that incorporates the latest production redesigned circuit to prevent this condition.
Transport CanadaMay 21, 19971997102Model years 1997View details →
On certain vehicles, the brake master cylinder may leak brake fluid due to a damaged double lip rear piston seal. Brake fluid leakage may result in diminished effectiveness of one portion of the split brake system. Correction: Rear brake master cylinder piston assemblies will be replaced.
Transport CanadaMay 17, 19961996079Model years 1995–1996View details →
An engine wiring harness may short due to contact with the exhaust gas recirculation (egr) tube. Shorting of the harness may cause various electrical malfunctions, including engine die out. Correction: Wiring harness will be properly routed and any damaged wiring will be replaced.
Transport CanadaFeb 12, 19961996029Model years 1996View details →
The rear brake hose mounting bracket screws can fail allowing the brake hoses to move out of position. The unrestrained hoses are then susceptible to damage which could result in brake fluid leakage.
NHTSA · United StatesFeb 23, 199494V034000Model years 1995View details →
Vehicles may experience an engine die out due to moisture in the powertrain control module (pcm) caused by inadequate potting material sealing. Also, the rear brake lines may be out of position due to failure of the mounting bracket screws. Correction: Powertrain control module and rear brake line bracket screws will be replaced on affected vehicles.
Transport CanadaFeb 21, 19941994038Model years 1995View details →
Vehicles may have been built with a rear abs brake master cylinder seal that may allow air ingestion into the cylinder and cause spongy brake feel or partial brake system loss. Correction: Vehicles will be inspected and suspect master cylinders will be replaced.
Transport CanadaFeb 8, 19941994024Model years 1995View details →
Vehicle description: Passenger vehicles built with 15" wheels, equipped with an r/t package. Certain vehicles were equipped with an incorrect tire placard. The vehicles were equipped with p195/50r16 tires but the tire placard indicated that the recommended tire sizes were p185/65r14 and p185/65r15. This does not comply with the requirements of fmvss no. 110, "tire selection and rims."
NHTSA · United StatesFeb 12, 200101V039000Model years 2001View details →
Vehicle description: Passenger vehicles equipped with the sport appearance package fail to comply with the requirements of fmvss 110, "tire selection and rims." certain vehicles built with 16" wheels and tires were equipped with the incorrect tire placard.
NHTSA · United StatesDec 12, 200000V415000Model years 2001View details →
Vehicle description: Certain passenger vehicles, pickup trucks and sport utility vehicles fail to comply with the requirements of fmvss no. 225, "child restraint anchorage systems." some of the owner's manuals for these vehicles are missing instructions that provide a step-by-step procedure, including diagrams, for properly attaching a child restraint system's tether strap to the tether anchorage.
NHTSA · United StatesNov 9, 200000V366000Model years 2000–2001View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).