The pressure regulator installed in the fuel supply plumbing system may be the source of fuel leakage which can cause an engine compartment fire. Correction: Fuel supply system pressure regulator and associated plumbing will be replaced with components of another configuration.
Transport CanadaAug 13, 19911991114Model years 1987View details →
On vehicles with 2.2 litre or 2.5 litre efi(non-turbo) engine, the valve cover gasket may leak oil creating the potential for an engine compartment fire. Correction: Valve cover gasket will be replaced with a revised cover and rtv sealant applied in place of the gasket.
Transport CanadaDec 20, 19891989178Model years 1989–1990View details →
Fuel leakage may occur in low ambient temperature operation at connections of an engine compartment fuel supply hose to the pressure regulator and to the fuel rail.
NHTSA · United StatesJul 1, 198888V105000Model years 1985–1987View details →
On certain vehicles equipped with a 2.2 Litre turbo engine, an inadequately tightened fuel hose clamp at the fuel system pressure regulator could result in fuel leakage and provide the potential for an engine compartment fire.
Transport CanadaFeb 5, 19851985021Model years 1985View details →
An engine compartment fuel hose routed to the fuel system pressure regulator may have an inadequately tightened hose clamp. Consequence of defect: The fuel hose could leak and result in an engine compartment fire.
NHTSA · United StatesJan 1, 198585V010000Model years 1985View details →
The potential for fuel leakage exists in the engine compartment at the fuel reservoir seam and its hose connections. The fuel reservoir is a silver colored can mounted to the air cleaner.
NHTSA · United StatesNov 21, 198484V147000Model years 1984–1985View details →
Rear suspension trailing arm-to-hanger bracket pivot bolts may fail from stress corrosion cracking possibly caused by processing deviations in the construction of the pivot bolt.
NHTSA · United StatesApr 11, 199191V056000Model years 1986View details →
These vehicles may experience a rear suspension trailing arm to hangar bracket pivot bolt failure, which could result in partial separation of the rear suspension from the vehicle. This could result in loss of vehicle control and a vehicle crash without prior warning. Correction: Involved vehicles will have both trailing arm pivot bolts replaced with properly processed bolts.
Transport CanadaApr 8, 19911991060Model years 1986View details →
These vehicles do not comply with c.M.V.S.S. 1103 - exhaust emissions. Plugged choke vacuum delay valve. Note: Vehicles equipped with 2.2 litre carbureted engines.
Transport CanadaJan 6, 19871987001Model years 1985–1986View details →
Battery cap vents may be partially or completely blocked with plastic flashing. Consequence of defect: A build up of internal gas pressure could occur which could result in case rupture, particularly during post charging. Should a person be in the vicinity of the battery when the case ruptures, they may be injured by the released gases and/or acid.
NHTSA · United StatesApr 10, 198686V053000Model years 1986View details →
An emissions system valve may allow an overly rich mixture (excessive fuel) in the engine during deceleration. The mixture of air and excessive fuel can cause the engine to stall while stopping, coasting, or turning.
NHTSA · United StatesSep 24, 198484V116000Model years 1985View details →
Involved vehicles may have been built with improperly forged or heat treated bolts used to attach the front suspension ball joints to the steering knuckles. Some of the bolts may eventually fail which could result in ball joint separation and affect vehicle directional controllability.
Transport CanadaMay 28, 19821982050Model years 1982View details →
Clamp bolts installed on certain vehicles may contain cracks. Eventually these bolts may break through, causing separation of the ball joint from the steering knuckle.
NHTSA · United StatesMay 27, 198282V055000Model years 1982View details →
On the involved vehicles, the bolts used to attach the front suspension ball joints to the control arms may fail due to a bolt section crack condition. The ball joint may separate from the arm possibly affecting vehicle directional control.
NHTSA · United StatesJan 28, 198282V011000Model years 1980View details →
The automatic speed control switch may stick in the "resume" position restricting return movement. This will not allow the normal brake pedal operation to deactivate the system.
NHTSA · United StatesSep 22, 198181V111000Model years 1981–1982View details →
The engine compartment fuel line hoses installed on certain vehicles were fabricated from a defective rubber compound. When subjected to continuous high underhood temperatures, these hoses may become brittle and crack.
NHTSA · United StatesOct 21, 198080V139000Model years 1980View details →
The hood secondary latch on the involved vehicles may be subject to binding due to variations in the latch and its mounting base assembly. A problem could occur if the primary latch became inoperative or was not properly engaged.
NHTSA · United StatesOct 17, 198080V138000Model years 1980View details →
Steering wheel horn pads do not contain the horn symbol display as required by fmvss 101.
NHTSA · United StatesJun 5, 198989V091000Model years 1988View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).