The cruise control release switch mounted on the brake master cylinder may have an improperly designed seal structure inside the switch. As a result, brake fluid can leak and reach the internal electrical terminals, corroding the contacts. This increases the resistance inside the switch, causing it to overheat and melt, and in the worst case, may lead to a fire.
In the lighting system, due to an inappropriate internal structure of the headlight switch, electrical resistance may increase at the contacts inside the switch, causing overheating and melting damage. As a result, the headlights may fail to turn on or may fail to turn off. In the worst case, this could lead to a fire.
If a short circuit occurs in the power mirror switch there is the potential risk of fire at or near the mirror switch (located in the driver's door). Overheating of the switch assembly creates the risk of an unattended vehicle fire. Correction: A fused jumper harness will be installed in the power mirror electrical circuit.
Transport CanadaJun 9, 19971997116Model years 1993–1994View details →
A short circuit condition can occur in the remote power mirror control switch circuit board as a result of a separated part of the contact assembly bridging the switch positive battery pad and adjacent chassis ground pad.
NHTSA · United StatesMay 5, 199797V083000Model years 1992–1994View details →
The hot plate weld which attaches the vapour vent valve to the top of the plastic fuel tank may partially fracture, allowing vapour or fuel to escape from the top of the tank through the fracture. In the presence of an ignition source a fire could result. Correction: Tanks will be removed and inspected for the weld integrity of the vapour vent valve carrier. Tanks with inadequate welds will be replaced.
Transport CanadaFeb 25, 19911991030Model years 1991View details →
The corner of the front heat shield may contact the upper front corner of the plastic fuel tank. This could damage the tank and allow fuel or fuel vapour to escape. In the presence of an ignition source, a fire could occur. Correction: Heat shield will be relocated and fuel tank will be inspected. Fuel tanks damaged by heat shield will be replaced.
Transport CanadaFeb 25, 19911991028Model years 1991View details →
The hot plate weld which attaches the vapor vent valve carrier to the top of the plastic fuel tank may partially fracture, allowing vapor of fuel to escape from the top of the tank.
NHTSA · United StatesFeb 11, 199191V025000Model years 1991View details →
If tires have been in use for a long period (more than 3 years since installation) and continue to be used, the tread may separate. In the worst case, the tread, or the tread together with the outer steel belt inside it, may peel off, which may impair driving stability.
Certain vehicles, from Ontario to Newfoundland, could experience a corrosion related failure of the spare tire winch cable. If the cable breaks while the vehicle is being driven, the spare tire could drop down, potentially creating a roadway obstacle. Correction: Owners are to inspect the cable, and if corrosion or broken wire strands are present the vehicle is to be taken to a dealer for replacement of the winch assembly. Program ends September 30, 2003.
Transport CanadaJul 16, 20012001193Model years 1991–1994View details →
Vehicle description: Multi-purpose passenger vehicles equipped with factory installed sunroof. The sunroof glass panel assembly can separate while the vehicle is moving due to incorrect hinge engagement. This was caused by improper sunroof installation of the glass panel.
NHTSA · United StatesDec 18, 199797V235001Model years 1991–1993View details →
The studs which attach the brake master cylinder to the power brake vacuum booster assembly can develop stress corrosion cracking after being operated for an extended period of time in the southern california location.
NHTSA · United StatesFeb 5, 199696V024001Model years 1991–1994View details →
Defect: The hydraulic lift cylinders on these vehicles are attached to brackets that are welded to the liftgate. Under certain conditions, the bracket welds may fracture due to the brackets being inadvertently mislocated relative to the liftgate. There may be a potential for the liftgate bracket to gradually bend inward which might allow the lift cylinder ball stud to disengage. Correction: Reinforcement brackets will be installed.
Transport CanadaAug 30, 19951995155Model years 1992–1993View details →
Note: This recall affects vehicles with manual transmission. The parking brake control self-adjust pawl may skip over one or more teeth in the self-adjust ratchet during parking brake application, which could prevent the system from achieving full tension. This could result in parking brake ineffectiveness which would allow the vehicle to roll freely if it is not left in gear. Correction: A wedge will be installed which will serve to lock the parking brake self-adjust mechanism pawl into engagement with the ratchet.
Transport CanadaOct 17, 19941994157Model years 1993–1994View details →
The parking brake control self-adjust pawl does not line up properly with the self-adjust rachet causing the pawl to slip over one or more teeth in the rachet.
NHTSA · United StatesSep 7, 199494V169001Model years 1993–1994View details →
Seat belt buckles on these vehicles may experience conditions whereby the buckle may not unlatch when the release button is depressed or may not latch, or in some cases, may latch partially but not sufficiently to provide occupant restraint in the event of a collision. Note: Only end-release buckles on "rigid" mountings are susceptible to this malfunction. Correction: Factory installed end-release seat belt buckles will be replaced with redesigned buckles.
Transport CanadaSep 29, 19921992120Model years 1991View details →
The rigid mounted safety belt buckles are defective in three ways. First, a fastened safety belt buckle will not unlatch when the release button is depressed. This results from interference between the buckle ejector finger and the buckle tongue window. The second defect is the safety belt buckle may not latch. The third possible defect is that the tongue may be retained by the buckle, but it may not be latched sufficiently to provide occupant protection.
NHTSA · United StatesAug 17, 199292V113000Model years 1991View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).