This file gathers the known defects of the Ford F-Series twelfth generation, written and sourced by the community. Anyone can read; a free account lets you contribute. A defect earns the seal once enough reputable contributors have validated it.
Owners often report problems with transmission and drivetrain on this car (3110 complaints), but no one has explained the cause yet. Do you know it?Write it up
Owners often report problems with engine on this car (1917 complaints), but no one has explained the cause yet. Do you know it?Write it up
1,039 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 2009–2013), typically at around 66,000 miles. Reported consequences: 14 crashes, 64 fires, 14 injuries.
✓ Mecafile analysis of official data2009–2013View details →
842 owners in the United States reported problems with the brakes of this car to NHTSA (model years 2009–2013), typically at around 57,000 miles. Reported consequences: 73 crashes, 5 fires, 31 injuries, 4 deaths.
✓ Mecafile analysis of official data2009–2013View details →
NHTSA, the US road safety agency, opened an engineering analysis (EA15006) into this problem on 16 October 2015 for 2011–2012 models; it was closed on 28 April 2016 without a recall.
✓ Mecafile analysis of official data2011–2012View details →
Issue: This recall is for aftermarket replacement rear window glass produced by Vitro Automotriz. Certain rear window glass may not have been properly tempered. If the window breaks, the glass may separate into large pieces instead of very small ones. Note: This is a voluntary recall that is not being conducted under the requirements of the Motor Vehicle Safety Act. Safety Risk: Glass that breaks in to large pieces could create a risk of injury. Corrective Actions: The company will notify consumers by mail and instruct them to inspect the designation code marked on the rear window glass. Products affected by this recall have the designation “DOT 287” along with the lettering “VMR” (Replacement Market) and a date code that is before July 2019. This information is printed on the bottom corner of the glass. Consumers should contact Vitro's customer service at 1-412-995-6457 or argbacklites@vitro.com to arrange for replacement of the glass.
Transport CanadaAug 21, 20192019420Model years 2009–2013View details →
Ford Motor Company (Ford) is recalling certain 2013 F-150 vehicles equipped with 5.0L or 6.2L gasoline engines, that previously had the powertrain control module (PCM) software reprogrammed under recall 19V-075. The software used to reprogram the PCM did not have the necessary updates to prevent the transmission from unexpectedly downshifting into first gear, regardless of vehicle speed.
NHTSA · United StatesJun 10, 201919V433000Model years 2013View details →
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
NHTSA · United StatesFeb 11, 201919V075000Model years 2011–2013View details →
This SKU is a DEF Injector. The customer communication requested return of unsold inventory to inspect the sealing. The injector sealing may have an issue which will cause a slow leak. A slow leak of the DEF Injector can lead to crystal formation which can cause aftertreatment related fault codes and ECU driven engine derating.
NHTSA · manufacturer bulletin10170197Model years 2012View details →
Some 2019 F-150 Raptor vehicles built on or before 15-Nov-2018 may exhibit a harsh or bumpy ride during all driving conditions. To resolve this concern, reprogram the vehicle dynamics control module (VDM) using the latest software version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 18B008 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA · manufacturer bulletin10153974Model years 2013View details →
Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
NHTSA · manufacturer bulletin10127405Model years 2011View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).