Airbag inflators can be defective and can build up excessive internal pressure when deployed. As a result, the metal inflator housing can rupture, so that metal fragments are propelled through the airbag and into the passenger compartment, injuring the vehicle's occupants.
EU Safety Gate · RappelConso · FranceJun 15, 2023a12/00544/20Model years 1996–2000Auto-translated · original: FrenchView details →
The airbag inflators may be defective and may create excessive internal pressure in the event of activation.As a result, the metal inflator casing may rupture, causing metal fragments to be propelled through the airbag and into the passenger compartment, injuring the vehicle occupants.
EU Safety GateMar 31, 2020A12/00544/20Model years 1996–2000View details →
In the driver-side airbag inflator (gas generator), moisture protection is inadequate, so the gas-generating agent may absorb moisture. Therefore, if the gas-generating agent repeatedly absorbs moisture and dries out during use, the airbag may not deploy normally when it is activated.
On vehicles equipped with a driving assistance device for manually operating the brake pedal, the welds between the brake link plate and shaft, which transmit the operating force, may have insufficient strength. As a result, if the brake arm is pushed further while the vehicle is stopped, excessive force may be applied to the welded portion, causing cracks. If the vehicle continues to be used in this condition, the cracks may grow and, in the worst case, the weld may break, causing the brakes to stop working.
In the engine starting system, some starter motor solenoid switches have an improperly assembled electrical terminal on the battery side. If the vehicle continues to be used in this condition, the insulating resin bushing at this terminal may deteriorate and crack. If liquid containing salt or other contaminants then gets on the terminal, a short circuit may occur there. In the worst case, the solenoid switch may burn out and the fire may spread through the engine compartment.
The airbag inflators were manufactured without the proper seals, which allows air and moisture to leak into the inflators over an extended period. As a result, the quality of the propellant deteriorates.
rdwMar 16, 2020MGP200112Model years 1999–2000Auto-translated · original: DutchView details →
In vacuum-type brake boosters (master power), due to improper crimping position of the booster housing during manufacturing, some units have a seal inside the master power that shifts when the brake pedal is depressed, so the negative pressure cannot be maintained. As a result, when the brakes are applied, the braking stopping distance may become longer than the driver expects.
In the engine, some units have an insufficient bearing surface area for the crankshaft timing belt guide plate because the mounting seat was machined improperly. If the vehicle continues to be used in this condition, the pulley mounting bolts may loosen and abnormal noise may occur. In the worst case, the crankshaft pulley may spin freely, or the auxiliary drive belt may come off the crankshaft pulley, causing the charge warning light to illuminate and the steering effort to increase.
Some of the resin molding in the motor section of the fuel pump for the electronic fuel injection system is defective. If use continues in this condition, the brush section may wear down, and in the worst case the fuel pump may stop operating, which could cause the engine to stop.
Some ignition control units (igniters) installed on vehicles equipped with electronically controlled fuel injection may fail due to the effects of ozone (O3) or heat generated by electrical discharge. If use continues in this condition, the control unit may stop operating, and the engine may become unable to start.
Some of the brackets connecting the control cable of the automatic transmission to the rod of the shift operating lever have insufficient retaining force. As a result, repeated shift operations may cause the bracket to come off, and the vehicle may become unable to shift even when the shift lever is operated.
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).