Free to read · free account to contributeSuccessor to Anticars (2000)

Honda Logo

1996–2001 · 1 generations · 2 documented defects · 1 markets
Generations
All generationsLogo1996–2001212
Model year
MarketAllEUJPUK
RecallCriticalInteriorEU

Airbag inflators can be defective and can create excessive internal pressure in the event of…

Airbag inflators can be defective and can build up excessive internal pressure when deployed. As a result, the metal inflator housing can rupture, so that metal fragments are propelled through the airbag and into the passenger compartment, injuring the vehicle's occupants.

EU Safety Gate · RappelConso · FranceJun 15, 2023a12/00544/20Model years 1996–2000Auto-translated · original: FrenchView details →
RecallCriticalInteriorJP

Airbag

In the driver-side airbag inflator (gas generator), moisture protection is inadequate, so the gas-generating agent may absorb moisture. Therefore, if the gas-generating agent repeatedly absorbs moisture and dries out during use, the airbag may not deploy normally when it is activated.

MLIT · JapanJan 23, 20201146460Model years 1996–1999Auto-translated · original: JapaneseView details →
RecallCriticalBrakesJP

Other (Other)

Vehicles equipped with the Manual Driving Assist Device (Honda Techmatic) have a brake link mechanism whose bearing structure is inappropriate, so excessive stress may be applied to the bearing section in some cases. If use is continued as is, cracks may develop in the fastening bolts of the bearing section and, in the worst case, the bolts may break, potentially causing the brakes to stop working.

MLIT · JapanNov 24, 20111128560Model years 1997–2002Auto-translated · original: JapaneseView details →
RecallCriticalSuspensionJP

Clip, bottle/nut

On four-wheeled vehicles, some wheel bolts used to attach the wheels to the running gear have been heat-treated improperly. If the vehicle continues to be used in this condition, the bolts may break and, in the worst case, the wheel may come off.

MLIT · JapanJun 6, 20011107490Model years 2001Auto-translated · original: JapaneseView details →
RecallCriticalBrakesJP

圧力制御伝達部

後輪の制動装置内部にあるピストンの表面処理に不適切なものがあるため、そのままの状 態で使用を続けると、ピストンに取り付けられているカップが摩耗しブレーキ液が漏れ、 最悪の場合、ブレーキが効かなくなるおそれがある。

MLIT · JapanAug 21, 19971104820Model years 1996–1997Shown in the original Japanese · translation pendingView details →
RecallModerateInteriorEU

Motor vehicles - bodywork (occupant protection devices)

The airbag inflators were manufactured without the proper seals, which allows air and moisture to leak into the inflators over an extended period. As a result, the quality of the propellant deteriorates.

rdwMar 16, 2020MGP200112Model years 1999–2001Auto-translated · original: DutchView details →
RecallModerateEngineJP

Starting device

In the engine starting system, the current flowing through the contacts of the ignition switch is large, so a strong arc discharge occurs at the moment the main power is turned on. Repeated starting operations cause excessive wear of the contacts and reduce contact pressure. As a result, vibration during driving may move the contacts, causing them to ride over carbon deposits and leading to poor conduction. In the worst case, the engine may stop suddenly. Note that restarting is possible, since the sliding of the contacts during the starting operation removes the carbon deposits.

MLIT · JapanMay 24, 20021108420Model years 1996–1999Auto-translated · original: JapaneseView details →
RecallModerateEngineJP

Engine body

In the engine, some units have an insufficient bearing surface area for the crankshaft timing belt guide plate because the mounting seat was machined improperly. If the vehicle continues to be used in this condition, the pulley mounting bolts may loosen and abnormal noise may occur. In the worst case, the crankshaft pulley may spin freely, or the auxiliary drive belt may come off the crankshaft pulley, causing the charge warning light to illuminate and the steering effort to increase.

MLIT · JapanOct 25, 20012101960Model years 1995–1997Auto-translated · original: JapaneseView details →
RecallModerateElectricalJP

前照灯

灯火装置において、前照灯操作スイッチ部の配線用端子の表面処理が不適切なため、前照 灯の切り替え操作を行うと当該端子の嵌合部が動くことにより接触抵抗が増大するものが あり、最悪の場合、接続カプラーが溶けて導通不良となり、前照灯が不灯となるおそれが ある。

MLIT · JapanSep 6, 20011107690Model years 1998–2001Shown in the original Japanese · translation pendingView details →

Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).