On certain vehicles, the brake booster may have been manufactured incorrectly and could develop a leak. As such, the booster may be unable to maintain vacuum when the brake pedal is depressed. Loss of brake power assist could occur, which may result in a crash causing property damage and/or personal. Correction: Dealers will inspect and, if necessary, replace the brake booster assembly.
Transport CanadaJun 12, 20132013207Model years 2006–2007View details →
On four-wheeled vehicles, some wheel bolts used to attach the wheels to the running gear have been heat-treated improperly. If the vehicle continues to be used in this condition, the bolts may break and, in the worst case, the wheel may come off.
Vehicle description: Passenger vehicles. Under certain conditions, the seat belt retractor can deform and cause complete or frequent locking of the retractor. As a result, the seat belts cannot be pulled out of the retractor and cannot be used.
NHTSA · United StatesOct 10, 200000V316000Model years 2000View details →
The two halves of the brake system's vacuum booster may have been clamped together incorrectly during manufacturing. As a result, the vacuum booster may start to leak.
rdwAug 15, 2013MGP130088Model years 2006–2007Auto-translated · original: DutchView details →
Brake assistance may be reduced or lost due to a manufacturing nonconformance. This could lead to longer stopping distances than the driver would normally expect.
DVSA · United KingdomJul 4, 2013R/2013/075Model years 2006View details →
null The seal which maintains a vacuum in the brake booster may be displaced when the brake pedal is pressed. This can result in a longer stopping distance than the driver expects.
EU Safety GateJun 28, 2013A12/0805/13Model years 2006View details →
In vacuum-type brake boosters (master power), due to improper crimping position of the booster housing during manufacturing, some units have a seal inside the master power that shifts when the brake pedal is depressed, so the negative pressure cannot be maintained. As a result, when the brakes are applied, the braking stopping distance may become longer than the driver expects.
American Honda Motor Co., Inc. (Honda) is recalling certain model year 2006 Acura RSX vehicles manufactured January 18, 2006, through August 12, 2006; and model year 2006-2007 Honda S2000 vehicles manufactured January 19, 2006, through November 13, 2006. The brake booster may be unable to maintain a vacuum when the brake pedal is depressed, decreasing brake assist.
NHTSA · United StatesJun 13, 201313V246000Model years 2006–2007View details →
Certain vehicles do not comply with the requirements of CMVSS 108. The lens of the side marker lamp and side reflex reflector in the tail lamp assembly were manufactured with incorrect dye that is more susceptible to UV and high temperature decomposition. As a result, the red colour could fade over time. Correction: Dealers will replace all affected tail lamp assemblies.
Transport CanadaJun 8, 20042004188Model years 2000View details →
Certain passenger vehicles fail to conform to the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment." the lens of the side marker lamp and side reflex reflector in the tail lamp assembly were manufactured with incorrect dye.
NHTSA · United StatesJun 1, 200404V257000Model years 2000View details →
The prime mover (engine) may have an improper combination of the engine and the spark plug gaskets. Under high-rpm heat loads, the gasket may deform and its clamping force may decrease. Vibration at high rpm may then cause the spark plug to loosen and produce abnormal noise, damaging the spark plug mounting threads and causing misfires that make the engine run poorly, and the engine control system warning light may illuminate. In the worst case, combustion gas blowing past the spark plug may melt the ignition coil and cause a short circuit, blowing the ignition system fuse, which could stop the engine and prevent it from restarting.
On certain vehicles, the seat belt retractor actuator can deform and cause unwanted, complete or infrequent, locking of the retractor. As a result, it may not be possible to pull the seat belt out of the retractor, rendering the belt unusable. Correction: Seat belt retractor will be repaired.
Transport CanadaOct 23, 20002000237Model years 2000View details →
On certain vehicles, the seat belts may not retract properly due to interference between the seat and the convertible top cover. This could cause excessive slack in the belts thereby reducing their effectiveness increasing the risk of injury to an occupant in a collision. Correction: The convertible top cover will be replaced with a new cover designed to prevent interference with the seat belt.
Transport CanadaFeb 28, 20002000046Model years 2000View details →
Vehicle description: Convertible passenger vehicles. When the convertible top is down and the seat is pushed all the way back, the seat belts may not retract properly resulting in slack in the seat belts.
NHTSA · United StatesJan 24, 200000V016000Model years 2000View details →
On certain passenger vehicles and motorcycles, the owner's manuals contain incorrect contact information for the national highway traffic safety administration's (nhtsa) vehicle safety hotline.
NHTSA · United StatesJul 26, 200606V270000Model years 2006View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).