Free to read · free account to contributeSuccessor to Anticars (2000)

Hyundai Excel

1985–1994 · 2 generations · 28 documented defects · 3 markets
Generations
Model year
MarketAllNA
Excel I · 1985–1990
Excel I · 1985–1990Excel II · 1989–1994
RecallCriticalEngineNA

Fuel system, gasoline

The vehicles failed the lateral moving barrier impact test requirements of fmvss 301, "fuel system integrity." the fuel leakage from the gas tank exceeded the maximum allowable amount of spillage.

NHTSA · United StatesNov 23, 199393V192000Model years 1990–1994View details →
Excel I · 1985–1990
RecallCriticalEngineNA

Engine

Note: All 1988-89 excel vehicles sold in canada. The reed valve subassembly contained within the air control valve could fail due to corrosion allowing the hot exhaust gases to flow backward into the plastic secondary air filter case when the vehicle is being driven. These hot gases may melt the secondary air filter case and could result in an engine compartment fire. Correction: Reed valve subassembly will be replaced.

Transport CanadaDec 30, 19911991176Model years 1988–1989View details →
Excel I · 1985–1990
Excel I · 1985–1990
RecallCriticalEngineNA

Fuel System

The fuel return tube clip may have been incorrectly installed allowing the fuel return hose to contact either the distributor high tension cable or the e.G.R. Valve. This could, over time, result in wear and eventual leakage at the fuel hose. The fuel leakage could result in an underhood fire. V.I.N. Range s.O.P. To kmhla31j1gu040086

Transport CanadaApr 18, 19861986044Model years 1986View details →
Excel II · 1989–1994
RecallModerateElectricalNA

Electrical system:Alternator/generator/regulator

In some vehicles, the manufacturer's protective internal coating of the electronic crank angle sensor does not meet specifications, which can cause an open circuit at high operating temperatures. This can cause the vehicle to stall.

NHTSA · United StatesMay 11, 199494V090000Model years 1994View details →
Excel I · 1985–1990
RecallModerateGearboxNA

Power train:Manual transmission

The manual transmissions may lock up from insufficient lubrication of the gears in the transmission case. This can cause the drive wheels to seize and the vehicle to come to a sudden stop.

NHTSA · United StatesOct 4, 199393V167000Model years 1986–1989View details →
Excel I · 1985–1990
RecallModerateEngineNA

Engine and engine cooling:Exhaust system

Deterioration of the reed valve subassembly may lead to a malfunction within the secondary air supply portion of the emission control system. The screws which attach the reeds to the reed valve subassembly may rust, and if the rusting becomes severe, the screw heads will erode and allow the reeds to separate from the reed valve subassembly. Corrosion may also occur on the reed valve subassembly, deforming the reed seats and preventing the reeds from closing properly. Separation of the reeds from the reed valve subassembly or improper closing of the reeds allow hot exhaust gases to flow backward into the plastic secondary air filter case when the vehicle is being driven. These hot exhaust gases may melt the secondary plastic air filter case.

NHTSA · United StatesDec 31, 199191V225000Model years 1986–1989View details →
Excel I · 1985–1990
RecallModerateSuspensionNA

Suspension

The lock washer located under the nut that secures the front hub to the driveshaft may crack due to improper heat treatment. This could result in wheel bearing freeplay and bearing damage with possible wheel lock-up or brake caliper knockback. Correction: Washer will be replaced note: All units have been corrected.

Transport CanadaMay 18, 19901990072Model years 1990View details →
Excel I · 1985–1990
RecallModerateSuspensionNA

Wheels:Hubcap/cover

Lock washer located under the nut that secures the front hub to the drive shaft may have had improper heat treatment and could crack.

NHTSA · United StatesMar 15, 199090V053000Model years 1990View details →
Excel I · 1985–1990
RecallModerateBrakesNA

Brakes

The possibility exists that under certain braking conditions, front brake fade may occur,thus reducing braking effectiveness. Correction: Improved semi-metallic brake pads will be installed.

Transport CanadaNov 27, 19871987127Model years 1986–1987View details →
Excel I · 1985–1990
RecallModerateBrakesNA

Recall

The cotter pin that retains the brake clevis pin may have been omitted or incorrectly installed. If the cotter pin was omitted or if it were to fall out of the clevis pin,the vehicles' brakes would be subject to failure without warning.

Transport CanadaMar 29, 19861986033Model years 1986View details →
Excel I · 1985–1990
RecallModerateBrakesNA

Service brakes, hydraulic:Pedals and linkages

A cotter pin in the brake pedal to brake master cylinder linkage assembly may be missing. This pin acts as a retainer for the brake master cylinder pushrod clevis pin. Consequence of defect: The clevis pin may slide out causing the master cylinder/brake pedal linkage to become disengaged. If this linkage becomes disengaged the service brakes cannot be applied, creating the risk of a crash without prior warning.

NHTSA · United StatesMar 17, 198686V043000Model years 1986View details →
Excel I · 1985–1990
RecallMinorElectricalNA

Vehicle speed control

If cruise control main switch is in the on position when engine is started, system can be affected by a short duration voltage drop caused by optional hi-power (h340) radio.

NHTSA · United StatesJun 19, 198989V100000Model years 1986–1989View details →

Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).