Free to read · free account to contributeSuccessor to Anticars (2000)

Mazda Mazda2

2002– · 3 generations · 13 documented defects · 7 markets
Generations

Service bulletins (TSBs) are repair instructions manufacturers send to their dealers about known problems. They are not safety recalls, but they often confirm a defect.

Model year
MarketAllNA
Mazda2 III · 2014–
BulletinModerateElectricalNA

Bulletin

Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.

NHTSA · manufacturer bulletin10199641Model years 2021View details →
Mazda2 III · 2014–
BulletinModerateElectricalNA

Bulletin

If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.

NHTSA · manufacturer bulletin10185813Model years 2017View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Some customers may complain about any of the following 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative.

NHTSA · manufacturer bulletin11039110Model years 2021View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Some vehicles may exhibit the check engine light ON with DTC P0300:00 (Random misfire detected) stored. This may be caused by a mis-detection of a misfire due to improper PCM control logic. To eliminate this concern, the PCM control logic has been modified.

NHTSA · manufacturer bulletin11012337Model years 2021View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Some customers may notice the charging lamp turns on while driving. Upon inspection, DTC P2502:00 PCM (Malfunction in voltage generated by generator) is stored in memory. This may be caused by resistance between the circuit board and ground. When high intensity electrical current passes through, the ground terminal position may not be sufficient enough. To eliminate this concern, the DC-DC converter control software has been modified. Additionally, the production procedure has been revised. The tightening torque for the ground terminal and circuit board was increased.

NHTSA · manufacturer bulletin11008418Model years 2021View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Some customers may experience a check engine light illumination at idle while stopped with DTC P0300:00 stored, resulting in rough idle conditions. P0300:00: Random misfire detected This concern is caused by improper engine control in the idle range. To eliminate the concern, the PCM control software has been modified.

NHTSA · manufacturer bulletin11008417Model years 2021View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

BSM Radar aiming cannot be performed after rightside BSM control module rekkplacement

NHTSA · manufacturer bulletin10213434Model years 2016View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Some customers may experience the CHECK ENGINE light ON with DTC P0089:00 (Spill valve control solenoid valve control circuit range/performance problem) stored. This is caused by improper control software of the PCM detecting a false error, even with normal fuel pressure operation. To correct this issue, the control software of the PCM has been modified.

NHTSA · manufacturer bulletin10190951Model years 2021View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Replace the Active Driving Display.

NHTSA · manufacturer bulletin10185954Model years 2016View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone. P2096:00 - Air fuel too lean P2097:00 - Air fuel too rich P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern.

NHTSA · manufacturer bulletin10180595Model years 2019View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display.

NHTSA · manufacturer bulletin10188483Model years 2016View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.

NHTSA · manufacturer bulletin10186918Model years 2017View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Active driving display opens/closes improperly. Some vehicles may exhibit the active driving display opening/closing improperly as described below: * It does not open or close when the ignition is turned ON or OFF . * The display operation does not fully open/close. * It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the act ive driving display which activates pinching detection. Customer having this concern should have their vehicle repaired using the following repair procedure.

NHTSA · manufacturer bulletin10186257Model years 2016View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Some customers may experience the active driving display (auto flip-up type) does not flip up and no DTC is stored. Due to improper assembly, a deformed bracket may cause a loose mesh between internal gears. To correct this issue, the active driving display has been changed.

NHTSA · manufacturer bulletin10144332Model years 2018View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Replace the Active Driving Display.

NHTSA · manufacturer bulletin10125470Model years 2016View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.

NHTSA · manufacturer bulletin10105642Model years 2016View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.

NHTSA · manufacturer bulletin10101468Model years 2016View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the active driving display. Replace the active driving display.

NHTSA · manufacturer bulletin10101464Model years 2016View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.

NHTSA · manufacturer bulletin10091601Model years 2016View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the active driving display. Replace the active driving display.

NHTSA · manufacturer bulletin10090902Model years 2016View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.

NHTSA · manufacturer bulletin10090667Model years 2016View details →
Mazda2 III · 2014–
BulletinMinorElectricalNA

Bulletin

Bsm radar aiming cannot be performed after right-side bsm control module replacement. If right-dide bsm control module requres replacement for any repair, also replace left side bsm control module to compelte the radar aiming procedure (it's ok to replace the left bsm alone). If the right-side bsm control module is replaced alone, "automatic configuration" is not performed due to program error in module. Because of this, the required "bsm radar aiming" cannot be performed. "automatic configuration" as well as "bsm radar aiming" can be performed if left-side bsm control module is replaced alone or together with right-side bsm control module.

NHTSA · manufacturer bulletin10076685Model years 2016View details →
Mazda2 II · 2007–2014
BulletinMinorElectricalNA

Bulletin

Mazda: There is possible excessive condensation or water inside the headlamp unit on many mazda models. *rm

NHTSA · manufacturer bulletin10037949Model years 2011View details →
Mazda2 II · 2007–2014
BulletinMinorElectricalNA

Bulletin

Mazda: There is condensation and fog in the front and rear combination lights. *rm

NHTSA · manufacturer bulletin10037655Model years 2011View details →

Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).