Service bulletins (TSBs) are repair instructions manufacturers send to their dealers about known problems. They are not safety recalls, but they often confirm a defect.
Some customers may experience the check engine light on with DTC P0126:00 (Thermostat stuck open) stored. This is due to improper PCM logic control. To eliminate the concern, the PCM control software has been modified. REPAIR PROCEDURE 1. Verify the customer concern. 2. Reprogram the ECU with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). Refer to MDARS ECU Reprogramming Procedure. NOTE: Be sure to submit Diagnostic Information (ODR) data as it is a required item and will be checked during warranty claim submission. Instructions can be found under M-MDS -> MDARS (Uploading Diagnostic Information (ODR) Data). 3. Clear any other DTCs. 4. Verify the repair by starting the engine (READY ON) and confirming there is no CHECK ENGINE light ON or abnormal warning lights present.
NHTSA · manufacturer bulletin11030600Model years 2026View details →
Some customers may experience the following concerns: The liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. The auto close operation of the power liftgate is not performed (The liftgate can be closed manually). To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified. Customers
NHTSA · manufacturer bulletin11003356Model years 2024View details →
Please be advised that the valve stem seals assigned to the 2.5 Skyactiv Turbo engines in GEPC are incorrect. The Diesel Valve Stem seal SH09-10-1F5A, which is for Diesel engines, is currently listed for these models in GEPC. Please ensure that the proper valve stem seals are used for the 2.5 Skyactiv Turbo engines affected by SSPD5 have the correct valve seal part number PY8W-10-1F5 installed on PYT engines to avoid any potential issues.
NHTSA · manufacturer bulletin11000679Model years 2021View details →
Some customers may experience that the liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified.
NHTSA · manufacturer bulletin10254184Model years 2024View details →
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA04_12004 or later). Ver. 7000C0A-NA04_12004 and later fixes these software errors (bugs): * Album artwork may not appear when playing music using an USB connected iPhone. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting into R position. * The screen freezes and goes to a white screen, then the system reboots. * The steering wheel switches and commander switches cannot control the audio system. * DTC U3000:49 is stored which may be accompanied with following symptoms: - No sound emitting from the speakers. - Audio source selection is unavailable. * The vehicle icon rotates when using the navigation with head-up mode. * Beep sounds every after couple of minutes. * Language setting may not be accepted correctly. * The audio track may not pause when pressing the mute button. * The system reboots. * The screen may turn black when trying to play a video file in the USB connected device.
NHTSA · manufacturer bulletin10226900Model years 2021View details →
Intermittent no crank/no start Some customers may complain about an intermittent no crank/no start. This may be caused by a poor instrument panel wiring harness connection C12. The accessory mirror with coimpass Tharness connector at drivers side Apillar may not be seated (locked) Properly secure the instrument panel wiring harness, upper and lower C12 connectors to resolve customer complaint.
NHTSA · manufacturer bulletin10213452Model years 2016View details →
Some vehicles may have a LOW ENGINE OIL LEVEL warning message and a CHECK ENGINE light illuminated in the instrument cluster, along with DTC P250F:00 stored in memory. DTC P250F:00 - Engine oil level signal: engine oil level low. Upon inspecting the engine oil level, the level is found to be low and there doesnt appear to be any trace of oil leakage in the engine compartment. This concern usually occurs when the mileage reaches approximately 3,100 4,700 miles (5,000 - 7,500km) and may also occur again after replacing or topping off the engine oil. The root cause of this concern has not been identified yet, therefore a repair procedure will be announced at a later date. Since this issue has been reported after a valve stem seal modification, it is very likely that valve stem seal damage is causing oil to leak into the combustion chamber.
NHTSA · manufacturer bulletin10203724Model years 2021View details →
Some vehicles may have a LOW ENGINE OIL LEVEL warning message and a CHECK ENGINE light illuminated in the instrument cluster, along with DTC P250F:00 stored in memory. DTC P250F:00 - Engine oil level signal: engine oil level low. Upon inspecting the engine oil level, the level is found to be low and there doesn't appear to be any trace of oil leakage in the engine compartment. This concern usually occurs when the mileage reaches approximately 3,100 - 4,700 miles (5,000 - 7,500km) and may also occur again after replacing or topping off the engine oil. The root cause of this concern has not been identified yet, therefore a repair procedure will be announced at a later date. Since this issue has been reported after a valve stem seal modification, it is very likely that valve stem seal damage is causing oil to leak into the combustion chamber.
NHTSA · manufacturer bulletin10202685Model years 2021View details →
Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built March 20, 2021 and later.
NHTSA · manufacturer bulletin10200937Model years 2021View details →
Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later.
NHTSA · manufacturer bulletin10200935Model years 2021View details →
Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later.
NHTSA · manufacturer bulletin10200934Model years 2021View details →
Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later. Engine no start due to low battery voltage.
NHTSA · manufacturer bulletin10199636Model years 2021View details →
Some customers may experience an instrument cluster warning message "Safety and Driver Support Systems Partially Disabled" and DTC U0401:68 [VEHICLE CONTROL MODULE (US)] (Error signal received from PCM, DSC HU/CM, instrument cluster, or body control module (BCM)) stored. This may be caused by the customer riding the brake pedal.
NHTSA · manufacturer bulletin10194774Model years 2019View details →
Some vehicles may have a "Low Battery Risk. Start Vehicle to Charge 12V Battery" warning message in the instrument cluster and a 30 second alarm sound. This may be caused by the customer doing any one of the following several times without starting the engine for an extended period of time: Open any door(s), Unlock doors, Open liftgate, Depress brake pedal, Push start/stop button. No dealer visit is required. The warning message can be cleared by starting the engine and idling or driving for 5 minutes or longer.
NHTSA · manufacturer bulletin10186807Model years 2021View details →
INSTRUMENT CLUSTER WARNING MESSAGE "SAFETY AND DRIVER SUPPORT SYSTEMS PARTIALLY DISABLED" AND DTC U0401:68 IS STORED:Some customers may experience an instrument cluster warning message "Safety and Driver Support Systems Partially Disabled" and DTC U0401:68 [VEHICLE CONTROL MODULE (US)] (Error signal received from PCM, DSC HU/CM, instrument cluster, or body control module (BCM)) stored. This may be caused by the customer riding the brake pedal.
NHTSA · manufacturer bulletin10170828Model years 2019View details →
WARNING MESSAGE SAFETY AND DRIVER SUPPORT SYSTEMS PARTIALLY DISABLED WITH DTC U2511:68: Some customer's may compain about warning message "Safety And Driver Support Systems Partially Disabled" with the following DTC's stored: U2511:68 DSC - Error signal received from electrical supply unit (ESU) U2511:68 VCM - Brake light control signal error. REPAIR PROCEDURE: U2511:68 DSC - Error signal received from electrical supply unit (ESU) Go to DTC U2511:68 [DSC HU/CM] U2511:68 VCM - Brake light control signal error Information is currently missing from Workshop Manual. MGSS will be updated soon. See service information below:
NHTSA · manufacturer bulletin10170826Model years 2019View details →
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
NHTSA · manufacturer bulletin10185813Model years 2017View details →
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected. Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.
NHTSA · manufacturer bulletin10168119Model years 2018View details →
Some vehicles may exhibit DTC B14F0:76 [VCM] (Forward sensing camera (FSC) deviation) stored in memory and the i-ACTIVSENSE warning light (amber) on after BCM replacement. This is caused by the learning value of the forward sensing camera (FSC) aiming being initialized after BCM replacement due to a software malfunction of the FSC. To correct this concern, the FSC software will be modified to not initialize the value of the FSC aiming after BCM replacement.
NHTSA · manufacturer bulletin10166849Model years 2019View details →
If a customer comes in with the following concerns, contact Hotline for assistance. OIL PRESSURE WARNING light and/or the CHECK ENGINE light ON, DTC P055F and/or P0524 stored, No drivability concern or engine mechanical noise, Outside the VIN range in TSB 01-020/18.
NHTSA · manufacturer bulletin10165353Model years 2019View details →
Some customer may experience all of the following when turning the ignition ON under hot weather conditions such as parking under the hot sun for some period of time: i-ACTIVSENSE warning light ON (1), Smart Brake Support (SBS) indicator light ON (2), "Excessive Camera Temp. Drive Safely" or "Safety and Driver Support Systems Temporarily Disabled" warning messages, DTC B14F9:00 stored in memory. DTC B14F9:00 cannot be found on MGSS, therefore repair cannot be performed.
NHTSA · manufacturer bulletin10164053Model years 2019View details →
Some vehicles may exhibit DTC U2120:00 and/or U2500:82 stored in memory and the i-ACTIVSENSE warning light (amber) ON when turning ON the ignition after any electronic control unit (ECU) is reprogramed or configured using MDARS. NOTE: ECU stands for general units (cameras and modules), all of which can be reprogrammed. This is caused by a software malfunction of the forward sensing camera (FSC). To correct this issue, the FSC software will be modified.
NHTSA · manufacturer bulletin10164075Model years 2019View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).