In some ignition switches, too much grease was applied to certain contact points. For a vehicle used under these conditions, this can cause the grease to carbonize, and therefore an increased risk of fire.
EU Safety Gate · RappelConso · FranceDec 15, 2022a12/00507/22Model years 1989–2000Auto-translated · original: FrenchView details →
null Over the time, the contact points inside the ignition switch may become carbonized and become conductive to electricity. As a result the ignition switch could overheat, leading to the risk of a fire.
EU Safety GateOct 6, 2016A12/1298/16Model years 1987–1998View details →
Carbonised grease may accumulate between the contact points in the ignition switch reducing the insulation performance inside the switch. In this condition the switch may generate heat resulting in smoke and in the worst case a fire.
DVSA · United KingdomSep 30, 2016R/2016/210Model years 1989–1998View details →
On certain vehicles, a defect in the ignition switch could cause an electrical short to develop over time. This could result in smoke and/or fire, increasing the risk of injury and/or damage to property. Correction: Dealers will replace the ignition switch.
Transport CanadaOct 19, 20152015489Model years 1989–1998View details →
Mazda North American Operations (Mazda) is recalling certain model year 1989-1998 MPV, 1990-1995 323, 1990-1998 Protege, 1992-1993 MX-3, 1993-1995 929, 1993-1997 MX-6, and 1993-1998 626 vehicles. In the affected vehicles, grease applied to the contact points inside the ignition switch may become conductive and overheat.
NHTSA · United StatesOct 19, 201515V674000Model years 1989–1998View details →
The ignition switch may have excessive grease applied to its internal contacts. The heat from the arc discharge generated when the switch is operated can carbonize the grease, causing it to accumulate between the movable and fixed contacts and reducing the insulation inside the switch. If use continues in this condition, the contacts may become conductive, causing the switch to overheat and emit smoke. In the worst case, this could lead to a fire.
THE (Takata) ABS PLASTIC FRONT SEAT BELT RELEASE BUTTONS ON THESE VEHICLES MAY BREAK ALLOWING PLASTIC PIECES TO FALL INTO THE BUCKLE ASSEMBLY. IF THIS SHOULD HAPPEN, A NO LATCH, FALSE LATCH OR FAILURE TO UNLATCH CONDITION COULD OCCUR CREATING THE RISK OF PERSONAL INJURY IN THE EVENT OF A CRASH OR SUDDEN STOP. CORRECTION: FRONT SEAT BELT BUCKLES WILL BE REPAIRED OR REPLACED AS NECESSARY.
Transport CanadaMay 24, 19951995085Model years 1989–1991View details →
Certain vehicles do not comply with Regulation 6 - Statement of Compliance. Vehicles have an incorrect National Safety Mark (NSM). Correction: Since this non-compliance does not present a risk to vehicle safety, no further action will be taken.
Transport CanadaAug 28, 20002000176Model years 1998View details →
The front safety belt buckle release buttons can break. These red plastic release buttons are marked "press." if a button breaks, pieces can fall into the buckle assembly causing the buckle to operate improperly.
NHTSA · United StatesMay 24, 199595V103005Model years 1989–1991View details →
The rear brake linings can change over time. As the brakes wear, the coefficient of friction can increase, producing inconsistent rear brake performance and premature activation of the abs system.
NHTSA · United StatesFeb 27, 199292V027000Model years 1990–1991View details →
Over a period of time the rear brakes on these vehicles may become more aggressive on brake application at low speed. This could result in rear wheel lock up and possible loss of vehicle control. Correction: Brake shoe assemblies will be replaced with improved parts. Note: Only vehicles without abs affected.
Transport CanadaOct 21, 19911991143Model years 1989View details →
Contamination of the vacuum brake hose check valve by detergent used in manufacture, could cause the valve to stick at low ambient temperatures thereby preventing its operation. Residual vacuum in the power brake system would provide power assist to the brakes on initial application, but the sticking valve would prevent vacuum build-up to provide continued power assist. This could result in increased stopping distances and a possible vehicle crash. Correction: Vacuum brake hose and check valve assembly will be replaced on affected vehicles.
Transport CanadaJan 24, 19911991017Model years 1989View details →
When the vehicle is exposed to temperatures below 5 degrees fahrenheit (-15 degrees c), the neutral detergent used as an assembly lubricant may stick to the check valve, preventing valve from functioning.
NHTSA · United StatesJan 22, 199191V013000Model years 1989View details →
These vehicles do not comply with c.M.V.S.S 209 - seat belt assemblies. The centre seat belt attachment hardware brackets for the third seat may not withstand the required tensile load of 6000 lbs or 26.7 kn. Correction: Centre seat belt assembly with bracket will be replaced on affected vehicles.
Transport CanadaNov 24, 19891989158Model years 1989View details →
On vehicles equipped with abs, an increase in the brake shoes' coefficient of friction can result in premature activation of the abs system. The noise and brake feel of this phenomenon may startle the operator who may then respond inappropriately presenting a possible risk to vehicle safety. Correction: Brake linings will be replaced with ones displaying different friction characteristics.
Transport CanadaApr 14, 19921992042Model years 1990–1991View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).