Fire may occur
Carbonised grease may accumulate between the contact points in the ignition switch reducing the insulation performance inside the switch. In this condition the switch may generate heat resulting in smoke and in the worst case a fire.
🔔 Create a free account to get email alerts about Mazda MX-6 I
Carbonised grease may accumulate between the contact points in the ignition switch reducing the insulation performance inside the switch. In this condition the switch may generate heat resulting in smoke and in the worst case a fire.
The ignition switch may have excessive grease applied to its internal contacts. The heat from the arc discharge generated when the switch is operated can carbonize the grease, causing it to accumulate between the movable and fixed contacts and reducing the insulation inside the switch. If use continues in this condition, the contacts may become conductive, causing the switch to overheat and emit smoke. In the worst case, this could lead to a fire.
燃料タンクの上部に取り付けられている樹脂製のロールオーバーバルブ取付用部品に成 形不良のものがあり、このままの状態で使用を続けると、当該部品と燃料タンクの間に隙 間が発生し、燃料が漏れるおそれがある。
THE (Takata) ABS PLASTIC FRONT SEAT BELT RELEASE BUTTONS ON THESE VEHICLES MAY BREAK ALLOWING PLASTIC PIECES TO FALL INTO THE BUCKLE ASSEMBLY. IF THIS SHOULD HAPPEN, A NO LATCH, FALSE LATCH OR FAILURE TO UNLATCH CONDITION COULD OCCUR CREATING THE RISK OF PERSONAL INJURY IN THE EVENT OF A CRASH OR SUDDEN STOP. CORRECTION: FRONT SEAT BELT BUCKLES WILL BE REPAIRED OR REPLACED AS NECESSARY.
The fuel tank straps may not be properly tightened and may rub against the fuel tank. This could cause the tank's protective coating to wear through resulting in surface damage and eventual tank perforation and fuel leakage. Correction: Rubber insulator will be placed between the tank straps and the tank and the tank straps will be properly tightened. Also, a new protective coating will be applied where required. V.I.N. Range: Jm1gd3120j1500014 to jm1gd2210j1537936
Fuel tank fixing band retention is not sufficient, allowing the band to rub against the fuel tank by vehicle vibrations.
The front safety belt buckle release buttons can break. These red plastic release buttons are marked "press." if a button breaks, pieces can fall into the buckle assembly causing the buckle to operate improperly.
At ambient temperatures below 0 degree f, frost may accumulate within the throttle body under extended constant speed operation.
At ambient temperatures below -18 degrees celsius, frost may accumulate within the throttle body under conditions of extended constant speed operation. This could result in a heavy accelerator pedal and cause uneven throttle valve return. Correction: The single stage engine coolant thermostat will be replaced with a dual stage thermostat equipped with a subvalve to increase the temperature within the throttle body. V.I.N. Range: Jm1gd3120j1500014 to jm1gd2226j1573252.
Vehicles equipped with rear brake drums transported by train may experience separation of the brake shoe from the wheel brake cylinder piston.
Transportation by rail could cause the rear brake shoe web to come off the wheel cylinder piston groove. This condition will cause damage to the wheel cylinder dust boot and may cause dust and water intrusion into the wheel cylinder resulting in piston corrosion. This would inhibit rear brake effectiveness. Correction: Vehicles will be inspected and wheel cylinder dust boot will be replaced where required. All involved vehicles will have lubricant applied to the wheel cylinder piston groove. V.I.N. Range: Jm1gd3120j1500014 to jm1gd2218j1541323
Floor mat could interfere with release of accelerator pedal due to improper shape of mat.
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).