Vehicle speed control
On certain pickup trucks, passenger vehicles, sport utility vehicles, and motor homes chassis, the speed control deactivation switch may, under certain conditions, leak internally and then overheat, smoke, or burn.
🔔 Create a free account to get email alerts about Mercury Capri (all generations)
On certain pickup trucks, passenger vehicles, sport utility vehicles, and motor homes chassis, the speed control deactivation switch may, under certain conditions, leak internally and then overheat, smoke, or burn.
The transmission fluid rubber tube connecting the transmission to the transmission oil cooler located in the radiator can become disconnected from the transmission, resulting in discharge of transmission fluid.
Prolonged exposure to sunlight may cause the front seat belt tongue assembly plastic sleeve that retains the lock bar to deteriorate and become displaced. This could potentially result in the tongue becoming detached from the seat belt webbing making the seatbelt useless to the vehicle occupant. Correction: Owners will be advised that ford will repair seat belts experiencing this condition.
The plastic sleeve in the front safety belt tongue assembly which retains the lock bar can deteriorate from prolonged exposure to sunlight and become displaced, causing the tongue to detach from the safety belt webbing.
The rubber tube that connects the transmission to the transmission oil cooler (in the radiator) may disconnect causing discharge of fluid.
On vehicles with efi or cfi, the spring-lock fuel line coupling used to connect the fuel supply and return lines to the efi fuel rails or to the cfi throttle bodies as well as other fuel line connections near the dash panels on some vehicles, could disengage during vehicle use. Should this occur, loss of fuel will result, providing the potential for a vehicle fire. Correction: Coupling retainer clips will be installed on affected vehicles. Note: Escort vehicles are equipped with efi and cfi. Lynx vehicles are equipped with cfi only. Efi - electronic fuel injection cfi - central fuel injection
The tandem power brake booster rear shells may have been produced with reduced wall thicknesses. Repeated brake applications could cau se such a shell to crack and the booster assembly to come apart.This could result in a total loss of braking capabilty without prior warn ing and present the possibility for loss of control and vehicle cras h.
The air bag modules do not meet the ford specifications for high ambient temperature performance.
The forward screw which provides part of the attachment between the driver`s seat back assembly and the seat cushion frame could fracture and permit the driver's seat back to pivot rearward. Such a condition could adversely affect the driver's ability to control the vehicle and could result in a vehicle crash. Correction: New driver's seat cushion attachment screws will be installed on affected vehicles.
Brake booster rear shells may have reduced wall thicknesses which could cause the shell to break. Consequence of defect: Repeated brake use could cause the shell to crack and the booster assembly to come apart. Service brakes capability would be totally lost without warning and could result in an accident.
The secondary throttle shaft may, with accumulated mileage, become contaminated and may stick in a partially open position while driving.
Carburetor throttle shafts may be susceptible to dirt contamination and wear of the bearing coatings. This could cause the secondary throttle plates to remain partially open after the driver has released the accelerator pedal. This this were to occur, engine speed would not return to idle potentially affecting vehicle control and stopping distances.
The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".
The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.
Some of the vehciles affected by the recall may have been produced with incorrect hoods - the incorrect hoods were intended for use with conventional (non-turbo) engines and maynot provide a sufficient clearnace between the throttle linkage and the hood undersides. As a result, under certain conditions, the throttle linkage may come in contact with the hood potentially causing damage to the linkage and preventing the throttle from returning to its idle position.
Inadequate clearance between the underside of the hood and the throttle linkage could damage the linkage and prevent the throttle from returning to idle position. This condition is due to installation of the incorrect hood style during vehicle assembly.
These vehicles do not comply with cmvss 209 - seat belt assemblies.
The housing plates on the driver seat back latch recliner assemblies were manufactured with substandard material products. This tainted steel was used to produce seatback latches for both the right and left side seat assemblies. Under certain conditions, the defective housing plates may distort, allowing the locking teeth to disengage and tear off. This permits the seatback to pivot backwards.
Vehicles produced at dearborn assembly plant. Vehicles may have been equipped with driver seat back latch recliner assemblies that contain housing plates manufactured from suspect steel material. Under certain types of driver induced seat loading the recliner mechanism housing plates might distort allowing the locking teeth to disengage. This would allow the seat back to rotate rearward into a reclined position.
Vehicles equipped with turbocharged 2.3l engines and manual transmissions. Vehicles may have been built without a particular electric curcuit in the idle tracking system wiring harness. This condition may cause exhaust emissions of hydrocarbon (hc) and carbon monoxide (co) gases to exceed the limits specified by canada motor vehicle safety standard 1103 - exhaust emissions.
During the railcar chain-down operation or during in-transit railcar movement, the chain could interfere with and break the evaporative emission carbon canister. These vehicles would then not comply with canada motor vehicle safety standard 1105 - evaporative emissions.
Note: Vehicles with 3.8 litre engines. These vehicles may not comply with c.M.V.S.S. 1103 - exhaust emissions. The substrate material in the catalysts may rattle and break up during normal use causing exhaust emissions to exceed the standard. Correction: Vehicles will be inspected and catalyst will be replaced where necessary.
Certain 1987-89 mustang 2.3 litre, 1986 mustang & capri 5.0 litre ho, and 1987-89 mustang & mark vii 5.0 litre ho. These vehicles may not comply with c.M.V.S.S. 1103 - exhaust emissions. The substrate in the catalyst may rattle and break up during normal use causing exhaust emissions to exceed the standard. Correction: Catalyst will be replaced where necessary.
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).