Free to read · free account to contributeSuccessor to Anticars (2000)

Mini Hatch III

2013–2024 · 11 documented defects · 3 markets

Service bulletins (TSBs) are repair instructions manufacturers send to their dealers about known problems. They are not safety recalls, but they often confirm a defect.

Model year
MarketAllNA
BulletinModerateEngineNA

Bulletin

Due to a manufacturing defect, the left charge air line can fail and cause an induction leak. In some casesthe Engine Malfunction warning may illuminate.

NHTSA · manufacturer bulletin10242925Model years 2024View details →
BulletinModerateEngineNA

Bulletin

The left charge air line can fail and cause an induction leak. In some cases the Engine Malfunctionwarning may illuminate. Note: This Service Information is similar to M11 03 23; though this one pertains to vehicles already retailed.

NHTSA · manufacturer bulletin10242926Model years 2024View details →
BulletinModerateEngineNA

Bulletin

B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil

NHTSA · manufacturer bulletin10216761Model years 2016View details →
BulletinModerateEngineNA

Bulletin

During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can give an appearance that there is an active engine oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, for example, oil filter changes, engine oil top-offs, etc. If this visual appearance of accumulated oil on the engine assembly is misinterpreted as an active engine oil leak, then unnecessary gasket repairs/replacements will result.

NHTSA · manufacturer bulletin10201151View details →
BulletinModerateEngineNA

Bulletin

SERVICE ACTION - MOUNTING THE OIL FILLER CAP CORRECTLY: The oil filler cap may not be mounted correctly. The cap was not installed correctly during assembly.

NHTSA · manufacturer bulletin10182925Model years 2021View details →
BulletinModerateEngineNA

Bulletin

SERVICE ACTION - MOUNTING THE OIL FILLER CAP CORRECTLY: The oil filler cap may not be mounted correctly. The cap was not installed correctly during assembly.

NHTSA · manufacturer bulletin10182626Model years 2021View details →
BulletinModerateEngineNA

Bulletin

ENGINE STALLS AFTER STARTING OR WILL NOT START. The engine stalls right after starting (when stationary).

NHTSA · manufacturer bulletin10153782Model years 2016View details →
BulletinModerateEngineNA

Bulletin

VANOS AND VANOS CENTRAL BOLT IDENTIFICATION. INFORMATION Replacing the VANOS gear central bolts or the VANOS gear will require a component inspection when the engine assembly has been previously replaced in one of the vehicles listed above. Ordering the parts via the model, production or VIN may provide the incorrect part numbers. The procedure below will help identify which VANOS parts are installed in the replacement engine. 11 36 7 608 788 Inlet adjustment unit Oulet adjustment unit Refer to the ETK and the repair instructions for one time use fastener and component information regarding additional screws, gaskets and seals.

NHTSA · manufacturer bulletin10151386Model years 2016View details →
BulletinModerateEngineNA

Bulletin

SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.

NHTSA · manufacturer bulletin10151154Model years 2015–2016View details →
BulletinModerateEngineNA

Bulletin

SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.

NHTSA · manufacturer bulletin10151152Model years 2015–2016View details →
BulletinModerateEngineNA

Bulletin

SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.

NHTSA · manufacturer bulletin10151153Model years 2015–2016View details →
BulletinModerateEngineNA

Bulletin

SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.

NHTSA · manufacturer bulletin10151055Model years 2016View details →
BulletinModerateEngineNA

Bulletin

SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.

NHTSA · manufacturer bulletin10151057Model years 2016–2017View details →
BulletinModerateEngineNA

Bulletin

SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.

NHTSA · manufacturer bulletin10151056Model years 2016View details →
BulletinModerateEngineNA

Bulletin

"N14 and N18 Engine: High-pressure Pump Repair Instruction. INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, ""Removing and installing or replacing high-pressure pump (N14, N18)"" has a procedure error. The current version of the Repair Instruction states to replace the highpressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15601.2.M130113... 8/30/2013 Page 2 of 2 All vehicles equipped with the N18 engine and produced from 3/2012 and later. When the engine is fitted with a Bosch High-pressure Pump (1) the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightning torques are correct. Refer to EPC for the applicable part numbers when making repairs. "

NHTSA · manufacturer bulletin10150238Model years 2013View details →
BulletinModerateEngineNA

Bulletin

"N14 and N18 Engine: High-pressure Pump Repair Instruction. INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, ""Removing and installing or replacing high-pressure pump (N14, N18)"" has a procedure error. The current version of the Repair Instruction states to replace the high-pressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/159...2/5/2014 Page 2 of 2 Bosch High-pressure Pump (1): All vehicles equipped with the N18 engine and produced from 3/2012 and later When the engine is fitted with a Bosch High-pressure Pump (1), the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightening torques is correct. Refer to EPC for the applicable part numbers when making repairs."

NHTSA · manufacturer bulletin10147960Model years 2013View details →
BulletinModerateEngineNA

Bulletin

ENGINE CRANKS, NO START AND/OR ENGINE COOLANT TEMPERATURE FAULTS: NOTE: The engine may also exhibit the same starting behavior as in Situation1.

NHTSA · manufacturer bulletin10145369Model years 2014View details →
BulletinModerateEngineNA

Bulletin

JCW ENGINE TUNING KIT - ENGINE LOSS OF POWER IN STOP-AND-GO DRIVING: The engine may lose power if the vehicle is decelerated, in gear, to a near stop and then accelerated again.

NHTSA · manufacturer bulletin10143573Model years 2016View details →
BulletinModerateEngineNA

Bulletin

Mini: The oil filter housing assembly is leaking engine oil and/or coolant. No model or years listed. *pe

NHTSA · manufacturer bulletin10054636View details →
BulletinMinorEngineNA

Bulletin

During a vehicle inspection and/or while addressing a customer's concern, the engine stabilizer bar/link appears to be worn.

NHTSA · manufacturer bulletin10228445Model years 2021View details →
BulletinMinorEngineNA

Bulletin

Mini parts logistics TEC 26 turbo charger return

NHTSA · manufacturer bulletin10216708Model years 2016View details →
BulletinMinorEngineNA

Bulletin

Service action: B46 AND B48 ENGINES - CHECK AND REPLACE CRANKSHAFT GUIDE BEARING

NHTSA · manufacturer bulletin10216762Model years 2014View details →
BulletinMinorEngineNA

Bulletin

B38, B46 and B48 Engines: Engine Replacement Procedures

NHTSA · manufacturer bulletin10216766Model years 2015View details →
BulletinMinorEngineNA

Bulletin

Engine will not start (no crank). The engine will not crank or the engine loses power while driving, followed by a no crank situation.

NHTSA · manufacturer bulletin10216767Model years 2016View details →
Older →

Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).