Bulletin
Due to a manufacturing defect, the left charge air line can fail and cause an induction leak. In some casesthe Engine Malfunction warning may illuminate.
🔔 Create a free account to get email alerts about Mini Hatch (all generations)
Service bulletins (TSBs) are repair instructions manufacturers send to their dealers about known problems. They are not safety recalls, but they often confirm a defect.
Due to a manufacturing defect, the left charge air line can fail and cause an induction leak. In some casesthe Engine Malfunction warning may illuminate.
The left charge air line can fail and cause an induction leak. In some cases the Engine Malfunctionwarning may illuminate. Note: This Service Information is similar to M11 03 23; though this one pertains to vehicles already retailed.
B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil
During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can give an appearance that there is an active engine oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, for example, oil filter changes, engine oil top-offs, etc. If this visual appearance of accumulated oil on the engine assembly is misinterpreted as an active engine oil leak, then unnecessary gasket repairs/replacements will result.
SERVICE ACTION - MOUNTING THE OIL FILLER CAP CORRECTLY: The oil filler cap may not be mounted correctly. The cap was not installed correctly during assembly.
SERVICE ACTION - MOUNTING THE OIL FILLER CAP CORRECTLY: The oil filler cap may not be mounted correctly. The cap was not installed correctly during assembly.
Air Conditioning System Leak Testing. The customer complains of poor or no air conditioning cooling. After further diagnosis, the system is found to be low or empty of a refrigerant charge, but when using an electronic leak detector, no leak can be found. CAUSE: In most cases, an electronic leak detector is not sufficient for identifying small leaks in the system. Electronic leak detectors can give false alarms and can lead to an improper diagnosis of small leaks. A leak cannot be located exactly if accessibility is impaired (in the case of the expansion valve, evaporator or condenser).
ENGINE STALLS AFTER STARTING OR WILL NOT START. The engine stalls right after starting (when stationary).
VANOS AND VANOS CENTRAL BOLT IDENTIFICATION. INFORMATION Replacing the VANOS gear central bolts or the VANOS gear will require a component inspection when the engine assembly has been previously replaced in one of the vehicles listed above. Ordering the parts via the model, production or VIN may provide the incorrect part numbers. The procedure below will help identify which VANOS parts are installed in the replacement engine. 11 36 7 608 788 Inlet adjustment unit Oulet adjustment unit Refer to the ETK and the repair instructions for one time use fastener and component information regarding additional screws, gaskets and seals.
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
During Engine Oil Service a Small O-Ring Is Found in the Oil Filter Housing. No customer complaint has been received. During the scheduled engine oil service, the technician notices a black rubber o-ring lying on the bottom of the engine oil filter housing. The o-ring has been dislodged from the non-return valve inside the engine oil filter housing. No subsequent engine damage occurs from the dislodged o-ring. Engine oil filter housing (1) Rubber o-ring (2) The material dimensions of the rubber o-ring are not satisfactory, allowing it to become dislodged from its installation location.
"N14 and N18 Engine: High-pressure Pump Repair Instruction. INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, ""Removing and installing or replacing high-pressure pump (N14, N18)"" has a procedure error. The current version of the Repair Instruction states to replace the highpressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15601.2.M130113... 8/30/2013 Page 2 of 2 All vehicles equipped with the N18 engine and produced from 3/2012 and later. When the engine is fitted with a Bosch High-pressure Pump (1) the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightning torques are correct. Refer to EPC for the applicable part numbers when making repairs. "
The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.
Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.
Service Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.
Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.
N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. The sealing plug was not tightened sufficiently during production.
N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. CAUSE The sealing plug was not tightened sufficiently during production.
N16 and N18 Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.
"N14 and N18 Engine: High-pressure Pump Repair Instruction. INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, ""Removing and installing or replacing high-pressure pump (N14, N18)"" has a procedure error. The current version of the Repair Instruction states to replace the high-pressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/159...2/5/2014 Page 2 of 2 Bosch High-pressure Pump (1): All vehicles equipped with the N18 engine and produced from 3/2012 and later When the engine is fitted with a Bosch High-pressure Pump (1), the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightening torques is correct. Refer to EPC for the applicable part numbers when making repairs."
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).