Free to read · free account to contributeSuccessor to Anticars (2000)

Nissan Juke

2010– · 3 generations · 21 documented defects · 5 markets
Generations
Model year
Juke I · 2010–2019
RecallCriticalEngineEU

An internal ignition switch may be defective

An internal ignition switch may be defective. As a consequence, the engine could unexpectedly stall while driving and under certain conditions the vehicle's airbag system may not function.

EU Safety GateAug 29, 2018A12/1281/18Model years 2017View details →
Juke I · 2010–2019
RecallCriticalEngineNA

Fuel System

On certain vehicles, the fuel pressure sensor may not have been tightened properly when the corrective measure of recall 2012-074 was performed. As a result, the fuel pressure sensor may loosen over time, which could cause a fuel leak. A fuel leak in the presence of an ignition source could result in a fire causing injury and/or damage to property. Correction: Dealers will inspect and retighten the fuel pressure sensor as necessary.

Transport CanadaMar 8, 20182018121Model years 2011–2012View details →
Juke I · 2010–2019
RecallCriticalEngineNA

Fuel system, gasoline

Nissan North America, Inc. (Nissan) is recalling certain 2011-2012 Nissan Juke vehicles previously remedied under recall 12V-069. During that recall remedy, the fuel pressure sensor may not have been properly tightened, potentially causing the sensor to loosen and leak fuel.

NHTSA · United StatesMar 7, 201818V156000Model years 2011–2012View details →
Juke I · 2010–2019
RecallCriticalEngineEU

Motorrijtuigen - krachtoverbrenging

Brandstofdruksensor niet correct vastgezet. Hierdoor kan de sensor onder invloed van warmte en trillingen losraken.

rdwMar 23, 2015MGP150107Model years 2012–2013Shown in the original Dutch · translation pendingView details →
Juke I · 2010–2019
RecallCriticalEngineNA

Fuel System

On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and the rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect the pressure sensor and tighten to specification. Note: This is an expansion of recall 2012-074. Vehicles that were repaired under the previous campaign are not affected because that remedy would have corrected the subject condition.

Transport CanadaNov 28, 20142014539Model years 2011–2014View details →
Juke I · 2010–2019
RecallCriticalEngineNA

Fuel system, gasoline

Nissan North America, Inc. (Nissan) is recalling certain model year 2012-2014 Nissan Juke, 2012-2013 Infiniti M56, QX56, and 2014-2015 Infiniti Q70 (V8 engine vehicles only), and QX80 vehicles. The fuel pressure sensors may not have been sufficiently tightened during production. As a result, the fuel pressure sensor may loosen with vehicle usage and cause a fuel leak.

NHTSA · United StatesNov 28, 201414V683000Model years 2012–2014View details →
Juke I · 2010–2019
RecallCriticalEngineJP

その他(燃料装置)

エンジンの燃料供給レールに取り付けている燃料圧力センサの締付けが不適切なため、エンジンの振動等により締付けが緩むものがある。そのため、燃料圧力センサの取付け部のねじを伝って燃料が漏れるおそれがある。

MLIT · JapanNov 27, 20141134761Model years 2010–2014Shown in the original Japanese · translation pendingView details →
Juke I · 2010–2019
Juke I · 2010–2019
RecallCriticalEngineUK

Fuel may leak

Nissan has identified that the fuel rail pressure sensor of some vehicles may have not been correctly tightened to the fuel rail of the engine and may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition in extreme cases fuel leakage may occur.

DVSA · United KingdomApr 3, 2012R/2012/024Model years 2010–2012View details →
Juke I · 2010–2019
RecallCriticalEngineNA

Fuel system, gasoline

Nissan is recalling certain model year 2011-2012 juke, infiniti qx and infiniti m vehicles. The fuel pressure sensors may not have been tightened to the correct specification. As a result, the fuel pressure sensor may loosen due to heat and vibration causing fuel to leak.

NHTSA · United StatesFeb 24, 201212V069000Model years 2011–2012View details →
Juke I · 2010–2019
RecallCriticalEngineNA

Fuel System

On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect for fuel leakage from the pressure sensor and the fuel rail. If there are no signs of a fuel leak, the fuel pressure sensor will be tightened to specifications. If a fuel leak is confirmed, the gasket between the sensor and the fuel delivery rail will be replaced, and the sensor will be tightened.

Transport CanadaFeb 23, 20122012074Model years 2011–2012View details →
Juke I · 2010–2019
Juke I · 2010–2019
Juke I · 2010–2019
Juke I · 2010–2019
RecallModerateEngineUK

Engine push start switch may malfunction

On affected models with a push start ignition switch the switch may remain in the pressed position and not return after switching the engine on. If the vehicle continues to be driven in this condition the emergency engine stop function may operate and cause the engine to unintentionally stop.

DVSA · United KingdomAug 4, 2015R/2015/133Model years 2013–2014View details →
Juke I · 2010–2019
Juke I · 2010–2019
RecallModerateEngineJP

始動装置

プッシュエンジンスタータスイッチを組み付けるイモビライザアンテナの成形条件が不適切なため、熱収縮により、当該プッシュエンジンスタータスイッチとの隙間が狭くなり、摺動抵抗が増加したものがある。そのため、そのまま使用を続けると、当該スイッチ操作時に押したまま戻らず、緊急停止操作と判定してエンジンを停止することがあり、最悪の場合、走行中にエンストするおそれがある。

MLIT · JapanJun 25, 20151135950Model years 2013–2014Shown in the original Japanese · translation pendingView details →
Juke I · 2010–2019
RecallModerateEngineJP

エンジン本体

エンジンのタイミングチェーンにおいて、プレートを連結するピンの耐久性が不足しているため、表面処理が摩耗するものがある。そのまま使用を続けると、プレートのピン挿入穴が摩耗してタイミングチェーン全長が伸び、チェーンガイドと干渉して異音が発生し、最悪の場合、タイミングチェーンが破損してエンストに至るおそれがある。

MLIT · JapanJun 25, 20151135940Model years 2010–2012Shown in the original Japanese · translation pendingView details →
Juke I · 2010–2019
RecallModerateEngineUK

Fuel may leak

On affected vehicles the fuel pressure sensor may not have been tightened to the correct specification. Heat and engine vibration may cause the sensor to loosen and in extreme cases allow fuel to leak.

DVSA · United KingdomMar 30, 2015R/2014/167Model years 2012–2014View details →
Juke I · 2010–2019
Juke I · 2010–2019
Juke I · 2010–2019
RecallModerateEngineUK

Engine may stall

The Turbocharger boost sensor bracket may separate from the air inlet tube. This means the boost pressure may be measured incorrectly and the engine warning lamp may be illuminated. During low-speed driving this could cause the engine to stall and not restart

DVSA · United KingdomJan 23, 2012R/2011/166Model years 2010–2011View details →
Juke I · 2010–2019
RecallModerateEngineNA

Engine

On certain vehicles, a weld at the boost sensor bracket may fail, allowing the bracket to separate from the air inlet tube. If this occurred, the engine would enter fail-safe driving mode, resulting in reduced motive power in which the vehicle could still be driven for short distances. Continued operation could cause the engine to stall which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the air inlet tube assembly.

Transport CanadaDec 12, 20112011431Model years 2011View details →
Juke I · 2010–2019

Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).