En raison d’une erreur dans le processus de pliage du coussin gonflable du conducteur, le bouclier thermique peut ne pas se déplacer complètement autour du gonfleur lorsque l’airbag est activé. par conséquent, le gaz chaud peut directement entrer en contact avec le panneau avant de l’airbag, causant des dommages de brûlure au matériau du sac. en conséquence, l’airbag peut se déchirer pendant l’inflation réduisant sa fonction protectrice.
EU Safety Gate · RappelConso · FranceMar 26, 2021a12/00391/21Model years 2019Shown in the original French · translation pendingView details →
The ignition switch position-retaining spring has some units that were scratched during molding due to improper maintenance of the molding equipment. As a result, repeated operation of the ignition key may break the spring. If many heavy items such as key rings are attached to the ignition key, vibration during driving may cause the key to rotate out of the ON position, cutting power to the vehicle and possibly stalling the engine. In addition, if an accident occurs in this condition, the airbags will not deploy.
An internal ignition switch may be defective. As a consequence, the engine could unexpectedly stall while driving and under certain conditions the vehicle's airbag system may not function.
EU Safety GateAug 29, 2018A12/1281/18Model years 2017View details →
On certain vehicles, the fuel pressure sensor may not have been tightened properly when the corrective measure of recall 2012-074 was performed. As a result, the fuel pressure sensor may loosen over time, which could cause a fuel leak. A fuel leak in the presence of an ignition source could result in a fire causing injury and/or damage to property. Correction: Dealers will inspect and retighten the fuel pressure sensor as necessary.
Transport CanadaMar 8, 20182018121Model years 2011–2012View details →
Nissan North America, Inc. (Nissan) is recalling certain 2011-2012 Nissan Juke vehicles previously remedied under recall 12V-069. During that recall remedy, the fuel pressure sensor may not have been properly tightened, potentially causing the sensor to loosen and leak fuel.
NHTSA · United StatesMar 7, 201818V156000Model years 2011–2012View details →
On certain vehicles, due to a manufacturing defect the start/stop button could stick inside of its housing. If this occurs, vibration could cause the electrical components inside the button to contact repeatedly in quick succession and initiate the emergency engine shut off procedure while the vehicle is in motion. This could result in increased steering and braking effort, a loss of motive power and would disable the supplemental restraint systems (SRS), increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect and repair defective start/stop switch as necessary.
Transport CanadaJun 25, 20152015282Model years 2013–2014View details →
null The fuel rail pressure sensor of some vehicles may be tightened insufficiently to the fuel rail of the engine and it may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition, in an extreme case, fuel leakage may occur between the fuel rail pressure sensor and the fuel rail.
EU Safety GateDec 5, 2014A12/1975/14Model years 2012–2014View details →
On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and the rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect the pressure sensor and tighten to specification. Note: This is an expansion of recall 2012-074. Vehicles that were repaired under the previous campaign are not affected because that remedy would have corrected the subject condition.
Transport CanadaNov 28, 20142014539Model years 2011–2014View details →
Nissan North America, Inc. (Nissan) is recalling certain model year 2012-2014 Nissan Juke, 2012-2013 Infiniti M56, QX56, and 2014-2015 Infiniti Q70 (V8 engine vehicles only), and QX80 vehicles. The fuel pressure sensors may not have been sufficiently tightened during production. As a result, the fuel pressure sensor may loosen with vehicle usage and cause a fuel leak.
NHTSA · United StatesNov 28, 201414V683000Model years 2012–2014View details →
In the event that the driver airbag is deployed during a frontal impact small holes may occur on the surface of the airbag. The holes are caused by high temperature gases from the airbag inflator exhausting directly onto the surface of the airbag material. The high temperature gas/airbag material may contact the drivers skin. The deployment performance of the driver airbag is not affected.
DVSA · United KingdomFeb 25, 2013R/2013/019Model years 2012View details →
null In the event that the driver's airbag is deployed during a frontal impact, small holes may appear on the surface of the airbag. The holes are caused by high temperature gas from the airbag inflator exhausting directly onto the surface of the airbag material. Contact of the high temperature gas / airbag material with the driver’s skin can cause burns.
EU Safety GateFeb 20, 2013A12/0243/13Model years 2012View details →
Nissan has identified that the fuel rail pressure sensor of some vehicles may have not been correctly tightened to the fuel rail of the engine and may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition in extreme cases fuel leakage may occur.
DVSA · United KingdomApr 3, 2012R/2012/024Model years 2010–2012View details →
Nissan is recalling certain model year 2011-2012 juke, infiniti qx and infiniti m vehicles. The fuel pressure sensors may not have been tightened to the correct specification. As a result, the fuel pressure sensor may loosen due to heat and vibration causing fuel to leak.
NHTSA · United StatesFeb 24, 201212V069000Model years 2011–2012View details →
On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect for fuel leakage from the pressure sensor and the fuel rail. If there are no signs of a fuel leak, the fuel pressure sensor will be tightened to specifications. If a fuel leak is confirmed, the gasket between the sensor and the fuel delivery rail will be replaced, and the sensor will be tightened.
Transport CanadaFeb 23, 20122012074Model years 2011–2012View details →
On affected vehicles the VIN stored in the vehicle system may not match the actual VIN of the vehicle. This may lead to a situation where a vehicle user can see information related to a different vehicle resulting in a data security breach.
DVSA · United KingdomJun 17, 2024R/2024/234Model years 2019–2023View details →
Due to a design change introducing an internal chamfer in the rear seat rear locking button, the lock actuating rod can catch on this chamfer, preventing its upward movement. As a result, the rear seatback may not be securely locked when returned to its upright position after folding, and the rear seat occupant and any objects stored in the luggage compartment may not be properly restrained in the event of an accident, which increases the risk of injury.
EU Safety Gate · RappelConso · FranceAug 8, 2023a12/01430/21Model years 2019–2020Auto-translated · original: FrenchView details →
A potential concern affecting the HEVC (Hybrid Electric Vehicle Control) module software has been identified which may cause a module reset of affected vehicles. Simultaneous pressing of brake and accelerator could cause engine stumble or stall.
DVSA · United KingdomApr 19, 2023R/2023/096Model years 2022View details →
Si l’accélérateur et les pédales de frein sont pressés simultanément, cela provoque une réinitialisation de la commande de véhicule électrique hybride (hevc). cela peut conduire à ce que le moteur trébuche ou décroche dans des conditions de conduite spécifiques (lorsque le moteur est froid, immédiatement après le démarrage), ce qui crée un risque d’accident.
EU Safety Gate · RappelConso · FranceApr 14, 2023a12/00724/23Model years 2022Shown in the original French · translation pendingView details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).