Seat belts:Rear/other
Certain passenger vehicles fail to conform to federal motor vehicle safety standard no. 210, 'seat belt assembly anchorages.' the passenger-side rear safety belt may have been installed with an incorrect nut and bolt.
🔔 Create a free account to get email alerts about Pontiac Sunfire (all generations)
Certain passenger vehicles fail to conform to federal motor vehicle safety standard no. 210, 'seat belt assembly anchorages.' the passenger-side rear safety belt may have been installed with an incorrect nut and bolt.
On certain passenger vehicles. If the engine fails to start and the driver holds the key in the "start" position for an extended period, high current flows through the ignition switch, and sometimes produces enough heat to melt internal switch parts.
Certain vehicles, after being exposed to substantial amounts of water, may experience deployment of either the driver or passenger front airbag without a crash. The owner’s manual for these vehicles does not provide specific information about this situation. Inadvertent deployment of the driver and / or passenger front airbag in a non-accident (non-impact) situation may cause damage to the surrounding vehicle environment (windshield / instrument panel), and create expensive vehicle repair, including replacement of the airbag module(s) and the Sensing and Diagnostic Module (SDM). In some instances, inadvertent deployment could cause minor injuries to vehicle occupants. Correction: GM will notify the owners of these 1996 and 1997 vehicles of the potential affect of water accumulating in the vehicle interior on the function of the airbag system (as included in the owner's manuals of 1998 and later model years vehicles).
On certain passenger vehicles. If the engine fails to start and the driver holds the key in the "start" position for an extended period, high current flows through the ignition switch, and sometimes produces enough heat to melt internal switch parts.
Vehicle description: Passenger vehicles. The wheel lug nuts were not tightened securely resulting in a fracture of the wheel studs.
Vehicle description: Passenger vehicles. The compact spare tire assemblies were assembled with incorrect rims. If the spare tire is underinflated, the bead can separate from the rim causing a rapid loss of air. This does not comply with the requirements of fmvss no. 110, "tire selection and rims."
On certain passenger vehicles, the rear lamps that provide stop and turn signals and tail lamp functions stop working because of inadequate contact between the bulb and socket. In addition, if one bulbs were to become inoperative while the vehicle was operating in cruise control, the cruise control would disengage when the remaining bulb was activated. If both lamps were to become inoperative, the cruise control would not engage.
Certain passenger vehicles and mini vans have lower pinion bearings in the power rack and pinion assembly in which the retainer tabs were not crimped properly. These and some other retainers used in vehicles assembled between january 1, 1996 and october 31, 1997, could fail and permit the ball bearings to escape.
Certain vehicles do not comply with the requirements of CMVSS 101- Location and Identification of Controls and Displays. Vehicles exhibit a condition in which the "Generator Low Voltage" indicator light will not illuminate under low voltage conditions. Correction: Dealers will reflash the vehicle PCM with new calibration software.
Note: Certain 1997-99 vehicles in Ontario, Quebec and the Atlantic provinces and 1995-99 vehicles in all other provinces and territories. Moisture may enter the Powertrain Control Module (PCM) as a result of corrosion after extended exposure to road salt. This can lead to symptoms including illumination of the "Check Engine" light or the engine running rough. If these symptoms are ignored the engine may stall and may not be able to be restarted. Correction: Dealers will seal the Powertrain Control Module (PCM) in a protective shield/cover assembly.
Vehicle description: Passenger vehicles. These vehicles do not comply with requirements of fmvss no. 101, "control location, identification, and illumination." the instrument panel backlighting may not function after adjusting the interior light intensity.
On certain vehicles located in Ontario, Quebec, New Brunswick, Nova Scotia, Prince Edward Island and Newfoundland, Moisture entering the Powertrain Control Module (PCM) as a result of corrosion can cause illumination of the "Check Engine" light or cause the engine to run rough. If these symptoms are ignored, the engine may stall and may not be able to be restarted. Correction: Dealers will inspect, clean and/or replace the Powertrain Control Module (PCM), then seal the PCM in a protective shield/cover assembly.
Certain vehicles may have a condition which could result in one of the rear suspension trailing arm bolts breaking. If this were to occur while the vehicle was in motion, vehicle control would be affected and a crash could occur without prior warning. Correction: Dealers will replace the rear suspension trailing arm fasteners.
Vehicle description: Passenger vehicles. One of the rear suspension trailing arm bolts can fatigue and break.
Because of certain calibrations in the air bag's computer, there is an increased risk of an air bag deployment in a low speed crash or when an object strikes the floor pan. Correction: The sdm module will be recalibrated to reduce the sensitivity to short and mid-duration commanded deployments.
Vehicle description: Passenger vehicles. Because of certain calibrations in the air bag's sensing and diagnostic module, an inadvertent air bag deployment could occur in a low speed crash or when an object strikes the floor pan.
These vehicles may not comply with c.M.V.S.S. 214 - side door strength. There may be mis-located welds at the joint between the left rocker panel inner reinforcement and the body side ring. In the event of a vehicle crash, the sheet metal structure may not perform as designed. This could result in reduced levels of occupant protection. Correction: Vehicles will be inspected for mis-located welds and, if necessary, up to five welds will be placed between the involved panels.
Vehicle description: Passenger vehicles. These vehicles were built with mis-located welds at the joint between the left rocker panel inner reinforcement and the body side ring. This does not meet the requirements of fmvss no. 214, "side door strength."
Vehicle description: Passenger vehicles. These vehicles were built with the potential for the interior lamps to come on unexpectedly while the vehicles are being driven. This does not meet the requirements of fmvss no. 101, "controls and displays."
These vehicles do not comply with c.M.V.S.S. 101 - control location and identification. The interior lamps may turn on by themselves, five to thirty minutes after the vehicle is started and cannot be turned off by the switch. The lamp control module will turn them off after thirty minutes. If the interior lamps turn on while the vehicle is being driven at night, the increased glare could make it more difficult to see objects outside the vehicle. Correction: Lamp control module will be tested and replaced if necessary.
These vehicles do not comply with c.M.V.S.S. 110 - tire selection and rims. The compact spare tire assemblies in these vehicles may have been assembled with rims that do not conform to dimensional and profile standards. If the tire is underinflated it can separate from the rim. Correction: Rim on the compact spare tire assembly will be replaced.
These vehicles may not comply with c.M.V.S.S. 108 - lighting equipment. Vehicles may exhibit a condition in which the front and/or rear hazard warning lamps (four-way flashers) do not flash when the hazard switch is activated. Correction: Vehicles will be inspected and hazard lamp switch replaced if necessary.
The front and/or rear hazard warning lamps (four-way flashers) do not flash when the hazard switch is activated. This fails to comply with fmvss no. 108, "lamps, reflective devices, and associated equipment."
Certain vehicles may not comply with CMVSS 1105 - Evaporative Emissions. Fuel injectors may exhibit leakage of fuel vapour due to a stress of the plastic encapsulant. Correction: fuel injectors on affected vehicles will be inspected for involved date codes and replaced if necessary.
The accelerator control cable could have been kinked during assembly causing high accelerator pedal effort, sticking accelerator control cable, or a broken accelerator control cable.
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).