On certain vehicles, the driver frontal airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Correction: Dealers will replace the driver airbag inflator on Saab 9-3 and 9-5 vehicles and replace the driver airbag module on Saturn Astra vehicles.
Transport CanadaFeb 3, 20162016052Model years 2006–2009View details →
General Motors LLC (GM) is recalling certain model year 2006-2011 Saab 9-3 vehicles manufactured May 31, 2002, to February 15, 2011, 2006-2009 Saab 9-5 vehicles manufactured June 7, 2005, to May 28, 2009, and 2008-2009 Saturn Astra vehicles manufactured April 11, 2007, to July 24, 2008. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.
NHTSA · United StatesFeb 3, 201616V063000Model years 2006–2009View details →
It has been identified that in the unlikely event of a collision where there is a need for the deployment of the driver airbag it is a possible that the drivers airbag module may separate form its mounting on the steering wheel horn plate.
DVSA · United KingdomDec 3, 2010R/2010/214View details →
Certain passenger vehicles equipped with b308 6-cylinder gasoline engines may experience overheating and burnout of the isolated gated bipolar transistor (igbt) within the ignition discharge module (idm) due to increased susceptibility to electrical loads.
NHTSA · United StatesOct 26, 200606V410000Model years 2002–2003View details →
Certain 2000-2002 Saab 9-3 and 9-5 model vehicles equipped with 4-cylinder gasoline engines, and 2001-2003 9-5 models equipped with 6-cylinder gasoline engines may experience overheating and burnout of the Isolated Gated Bipolar Transistor (IGBT) within the Ignition Discharge Module (IDM) due to increased susceptibility to electrical loads. Overheating of the IGBT occurs most often at engine start-up but may also occur while the engine is running. When the IDM fails on a 4-cylinder while it is running, the engine may stall without warning, with no ability to be restarted. When the IDM fails on a 6-cylinder engine while it is running, the driver will initially experience reduced power and rough operation because the engine will only be running on three cylinders. The check engine light will flash. If the driver continues, unburnt fuel in the exhaust can cause thermal damage to the catalytic converter. The engine may stall and not restart. Correction: Dealers will inspect and, if required, replace the IDM.
Transport CanadaSep 20, 20052005271Model years 2000–2003View details →
Certain passenger vehicles equipped with b205/b235 4-cylinder gasoline engines and b308 6-cylinder gasoline engines may experience overheating and burnout of the isolated gated bipolar transistor (igbt) within the ignition discharge module (idm) due to increased susceptibility to electrical loads.
NHTSA · United StatesSep 14, 200505V399000Model years 2000–2002View details →
On certain passenger vehicles, if an owner changes their wheels/tires between summer and winter using a steel wheel in the winter and an alloy wheel in the summer, it is possible for rust and contamination to build up on the wheel hub during the steel wheel usage. If this occurs and the contamination is not removed, it is possible that after the tire change service, some of this contamination could flake or grind away resulting in reduced clamping force of the wheel to the hub. Over several seasons, it is possible that this reduced force could result in fractures developing in the wheel bolts due to wheel to hub movement.
NHTSA · United StatesJan 13, 200303V006000Model years 1999–2003View details →
Saab is recalling 57,389 my 2002-2008 9-5 series vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 201, "occupant protection in interior impact." during compliance testing, one of the upper interior occupant protection test points exceeded the standard's requirements.
NHTSA · United StatesApr 9, 200808V160000Model years 2002–2008View details →
On certain vehicles, when changing back and forth between alloy and steel wheels (as for winter tires), rust and other contaminates may build up on the mating surface of the wheel hubs. If this surface is not cleaned between wheel changes, uneven torque forces may cause wheel bolts to fracture. Although this is most likely to happen during wheel change service, it is possible that the bolts may break later while the vehicle is being driven. Correction: Dealer will clean the hub and reinstall the wheel with improved bolts and attached washers that will eliminate the clamping force reduction.
Transport CanadaDec 23, 20022002247Model years 1999–2003View details →
A combination of internal and external forces caused the towball to prematurely detach itself from the towball housing resulting in separation of the trailer from the drawing unit.
DVSA · United KingdomJul 11, 2002R/2002/093View details →
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).