エアバッグ
運転者席用エアバッグのインフレータ(膨張装置)において、吸湿防止が不適切なため、ガス発生剤が吸湿することがある。そのため、使用過程でガス発生剤が吸湿や乾燥を繰返した場合など、エアバッグ作動時に正常に展開しないおそれがある。
🔔 Create a free account to get email alerts about Toyota Corolla E80 (all generations)
運転者席用エアバッグのインフレータ(膨張装置)において、吸湿防止が不適切なため、ガス発生剤が吸湿することがある。そのため、使用過程でガス発生剤が吸湿や乾燥を繰返した場合など、エアバッグ作動時に正常に展開しないおそれがある。
In the passenger-side airbag inflator, the moisture protection of the gas generant is inadequate. Repeated changes in temperature and humidity may cause the gas generant to deteriorate. As a result, the inflator housing may rupture when the airbag deploys.
助手席用エアバッグのインフレータ(膨張装置)において、ガス発生剤の吸湿防止が不適切なため、温度および湿度変化の繰り返しによりガス発生剤が劣化することがある。このため、エアバッグ展開時にインフレータ容器が破損するおそれがある。
助手席エアバッグのインフレータ(膨張装置)において、ガス発生剤の成型工程が不適切又は成型後の吸湿防止措置が不適切なため、エアバッグ展開時にインフレータ内圧が異常上昇し、インフレータ容器が破損して飛び散り、出火したり乗員が負傷するおそれがある。
助手席用エアバッグのインフレータ(膨張装置)において、ガス発生剤の成型工程が不適切又は成型後の吸湿防止措置が不適切なため、密度が不足したガス発生剤が組み込まれたものがある。そのため、エアバッグ展開時にインフレータ内圧が異常上昇し、インフレータ容器が破損して飛び散り、出火するおそれがある。
In vehicles fitted with the washer fluid anti-freeze heater offered as a dealer option, the O-ring used to waterproof the heater control circuit unit has insufficient compression (squeeze). As a result, washer fluid may seep into the control circuit. This can cause the control circuit to melt from overheating and, in the worst case, may lead to a fire.
助手席用エアバッグのインフレータ(膨張装置)内のガス発生剤組付け作業が不適切なため、ガス発生剤の装填量が不足しているものがある。そのため、車両の振動でガス発生剤が粉状となり、エアバッグが展開するとインフレータ内圧の異常な上昇で容器が破損して構成部品が飛散し、乗員が負傷するおそれがある。
2パワーステアリング用油圧パイプの固定方法が不適切なため、エンジン振動等により位置がずれるものがある。そのため、当該油圧パイプの固定状態によってはブレーキパイプと接触し、そのまま使用を続けると、ブレーキパイプが損傷してブレーキ液が漏れ、制動力が低下するおそれがある。
圧縮天然ガス自動車において、燃料を供給する高圧レギュレータの密閉プラグ締付け力 が不足しているため、エンジン始動時の当該密閉プラグに掛かる圧力変動により、密閉プ ラグが緩むものがある。そのため、そのまま使用を続けると、密閉プラグに取付けられて いるオーリングが損傷し、燃料が漏れるおそれがある。
制動装置において、ブレーキマスタシリンダ(油圧発生部)からアクチュエータ(油圧制 御装置)までの間のブレーキパイプを組み付け時に変形させたものがあるため、そのまま の状態で使用を続けると、原動機の振動等により当該ブレーキパイプがパワーステアリン グ用油圧パイプと接触して損傷し、最悪の場合、ブレーキ液が漏れて制動力が低下するお それがある。
1. In the steering gear, the joint component connecting the steering wheel and the gearbox (intermediate extension shaft) may have insufficient strength on the gearbox side. Therefore, repeatedly turning the steering wheel forcefully to full lock at low speed may cause play to develop at the joint's connection. If use continues in this condition, the connection may wear down, and steering operation may become impossible.
The shape of the contacts inside the headlight switch is inappropriate, so the contacts may wear out quickly. Wear debris carries sliding grease onto the contacts, forming an insulating deposit. As a result, the headlights may occasionally fail to turn on. If use continues, the electrical resistance of the contacts increases and they overheat, which may melt the resin parts and cause the lights to go out.
1制動灯用スイッチの接点にはたらく電気負荷に対する接点部の形状が不適切なため、接 点に酸化物が生成され接触抵抗が増大するものがある。そのため、スイッチが導通不良と なり、制動灯が点灯しなくなるおそれがある。
オートマチック車のシフトロック機能を解除するリンクの樹脂製ガイド部の成型形状が 不適切なため、リンクがガイド部に引っ掛かり、リンクが戻らず、シフトロックが解除さ れたままになるものがある。そのため、ブレーキペダルを踏まなくても、Pレンジからシ フトレバーを操作できるおそれがある。
自動変速機付き車のシフトレバー内部にある樹脂製ロッドが、強度不足のため、当該ロッ ドが折損してブレーキを踏まなくてもシフトできるようになることがあり、最悪の場合に は、シフト機構と連動しているキーインタロック装置が正常に作動しなくなり、イグニッ ションキーが抜けず、また、かじ取り装置の施錠装置が機能しなくなるおそれがある。
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).