Free to read · free account to contributeSuccessor to Anticars (2000)

Toyota Sequoia

2000– · 3 generations · 22 documented defects · 3 markets
Generations
Model year
MarketAllEUNAUK
Sequoia II · 2007–2022
RecallCriticalElectricalNA

Electrical

Issue: This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: This recall only affects the following block heater/cord part numbers: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Safety Risk: Engine block heater wiring that overheats or melts could create the risk of a fire. Corrective Actions: Toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.

Transport CanadaNov 24, 20212021723Model years 2008–2019View details →
Sequoia I · 2000–2007
RecallCriticalInteriorNA

Airbag

Issue: On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the passenger-front airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Safety Risk: If the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective Action: Owners will be notified by mail and instructed to take their vehicle to a dealer to have the passenger-front airbag inflator or airbag module replaced. Note: The Canadian climate results in the propellant degrading slowly. This recall is being conducted as a precaution to address future risk. It is expected that all airbag inflators will be replaced before their function would be affected. Additional Note: Vehicles may have had the original front passenger airbag inflator replaced as a "like-for-like" replacement under recall 2016-103 (Toyota Recall #'s SRC 241 & SRC 242) as a temporary remedy while evaluating a permanent remedy. These vehicles will receive the permanent remedy passenger airbag assembly under this recall.

Transport CanadaOct 17, 20192019523Model years 2002–2007View details →
Sequoia I · 2000–2007
RecallCriticalInteriorNA

Air bags:Frontal:Passenger side:Inflator module

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

NHTSA · United StatesOct 17, 201919V741000Model years 2002–2007View details →
Sequoia I · 2000–2007
RecallCriticalInteriorNA

Airbag

On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, could eventually degrade the propellant contained in the passenger frontal airbag. This could cause the airbag to deploy with more force than normal. As a result, if the vehicle were involved in a collision that warrants airbag deployment, fragments could be propelled toward vehicle occupants, and the airbag assembly could be damaged, preventing proper function. These issues could increase the risk of injury. Correction: Dealers will replace the passenger frontal airbag inflator or airbag assembly. <br><br> Note: Canadian climate results in the propellant degrading slowly. The recall is being conducted as a precaution to address future risk, and is expected to replace airbag inflators before their function would be affected. Vehicles may have had the original front passenger airbag inflator replaced as a “like-for-like” replacement under recall 2013-133 (Toyota Recall #'s SSC 193/241 & SSC 194/242) as a temporary remedy while evaluating a permanent remedy. These vehicles will receive the permanent remedy passenger airbag assembly under this recall.

Transport CanadaDec 12, 20182018699Model years 2002–2003View details →
Sequoia I · 2000–2007
RecallCriticalInteriorNA

Air bags:Frontal:Passenger side:Inflator module

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2002-2005 Lexus SC and Toyota Sequoia, 2003-2005 Toyota Corolla and Tundra, and 2003-2007 Pontiac Vibe vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation.

NHTSA · United StatesDec 12, 201818V883000Model years 2002–2005View details →
Sequoia II · 2007–2022
RecallCriticalInteriorNA

Airbag

Certain vehicles may not comply with the requirements of Canada Motor Vehicle Safety Standard (CMVSS) 208 - Occupant Protection in Frontal Impacts and CMVSS 214 - Side Impact Protection. The airbag (SRS) control unit may incorrectly detect a fault in one or more of the front or side airbag impact sensors during vehicle start up. In the event of a crash where airbag deployment is required, this may result in the airbags not deploying as designed, increasing the risk of injury. Upon detection of a fault in the airbag system, multiple warning lights would activate, a warning buzzer would sound, and a warning message would display on the instrument panel display. Correction: Dealers will update the airbag control unit software. Note: This recall supersedes recall 2018-100. Vehicles repaired as part of the previous recall will require re-inspection and repair.

Transport CanadaOct 5, 20182018547Model years 2018–2019View details →
Sequoia II · 2007–2022
RecallCriticalElectricalNA

Electrical system:Software

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2019 Toyota Tundra and Sequoia vehicles and 2019 Toyota Avalon and Avalon Hybrid vehicles. The air bag electronic control unit (ECU) may erroneously detect a fault during the vehicle start-up self check. If this occurs, the ECU may not deploy the airbags as intended, in the event of a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection," and 214, "Side Impact Protection."

NHTSA · United StatesOct 4, 201818V685000Model years 2018–2019View details →
Sequoia II · 2007–2022
RecallCriticalElectricalNA

Electrical

Certain vehicles may fail to comply with the requirements of Canada Motor Vehicle Safety Standard (CMVSS) 126 - Electronic Stability Control Systems. Electrical noise could be introduced into the YAW rate sensor within the airbag ECU, which could result in deactivation of the Vehicle Stability Control and Pre-Collision systems and limited function of the Trailer Brake Controller system. This would be contrary to the requirements of the standard, and could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will update the software of the ECU. Note: This recall is superseded by recall 2018547. Please see <a href="http://wwwapps.tc.gc.ca/Saf-Sec-Sur/7/VRDB-BDRV/search-recherche/detail.aspx?lang=eng&&rn=2018547">recall 2018547</a> for more information.

Transport CanadaFeb 21, 20182018100Model years 2018View details →
Sequoia II · 2007–2022
RecallCriticalElectricalNA

Electrical

On certain vehicles, the electrical power cords of some dealer installed block heaters may have been improperly manufactured, causing the wires to contact each other, resulting in a short circuit. A short circuit could lead to a fire which would increase the risk of injury and/or damage to property. Correction: For vehicles where the subject block heater was approved for installation, the dealer will replace the block heater assembly with a new one of an improved design. For vehicles where the subject block heater was not approved for installation, dealers will remove the block heater assembly. In the interim, until the remedy can be performed, dealers will cut the plug end from the block heater cord to disable the block heater's operation.

Transport CanadaJul 20, 20172017363Model years 2016–2017View details →
Sequoia II · 2007–2022
RecallCriticalSuspensionNA

Wheels:Lugs/nuts/bolts/studs

Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2013-2017 Toyota Tundra and Sequoia vehicles accessorized with Southeast Toyota accessory 20-inch Rockstar wheels installed by Southeast Toyota or a Southeast Toyota dealer. The Rockstar wheels were installed with lugnuts that may crack and detach.

NHTSA · United StatesMay 11, 201717V311000Model years 2013–2017View details →
Sequoia I · 2000–2007
RecallCriticalInteriorUK

Curtain airbags and seat belt pre-tensioners may deploy incorrectly

Due to improper programming of the airbag system in the Airbag Sensor Assembly (airbag control module) there is a possibility that the Airbag Sensor Assembly may erroneously detect a rollover and deploy the Curtain Shield Airbags (CSA) and seat belt pre-tensioners. The deployment of the CSA could cause minor injury to a vehicle occupant.

DVSA · United KingdomOct 31, 2016R/2016/012Model years 2004–2006View details →
Sequoia I · 2000–2007Sequoia II · 2007–2022
RecallCriticalInteriorNA

Seats:Front assembly:Seat heater/cooler

Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed.

NHTSA · United StatesJun 2, 201616V396000Model years 2005–2011View details →
Sequoia I · 2000–2007
RecallCriticalInteriorNA

Airbag

On certain vehicles, the passenger (frontal) airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the passenger airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Note: This recall supersedes recalls 2013113, 2014224, 2015197 and 2015269. Correction: All vehicles having not received a replacement inflator as part of the previous recall will now have a replacement inflator installed by dealers. For Matrix model vehicles, dealers may replace the front passenger airbag assembly with one equipped with a newly specified inflator.

Transport CanadaMar 2, 20162016103Model years 2002–2007View details →
Sequoia I · 2000–2007
RecallCriticalInteriorNA

Airbag

On certain vehicles, the roll rate sensors in the airbag control module may improperly calibrate if the vehicle experiences a body roll motion approximately four seconds after the ignition is turned to the ‘ON’ position. If the vehicle experiences another subsequent body roll motion, the system may erroneously detect a rollover, causing both of the side curtain airbags to deploy and the seat belt pre-tensioners to be activated. Unintended airbag and/or seat belt pre-tensioner deployment, in a non-warranted (non-impact) situation, could result in injury and increase the risk of a vehicle crash causing injury and/or property damage. Correction: Dealers will replace the airbag control module with one which has improved programming.

Transport CanadaFeb 2, 20162016051Model years 2005–2006View details →
Sequoia II · 2007–2022
RecallCriticalElectricalNA

Visibility:Power window devices and controls

Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.

NHTSA · United StatesOct 22, 201515V689000Model years 2009–2011View details →
Sequoia II · 2007–2022
RecallCriticalElectricalNA

Electrical

On certain vehicles, inconsistent application of grease during the manufacturing process could cause the driver's side power window master switch to stick or become inoperative due to electrical contact point wear. This could cause debris to accumulate between the contact points, potentially resulting in an electrical short circuit. If a short circuit occurs, the switch assembly may overheat, produce smoke, melt and/or potentially lead to a fire causing injury and/or property damage. Correction: Dealers will inspect the driver's power window master switch and apply a specialized grease that inhibits heat build-up, or replace the power window master switch circuit board, as necessary. Note: This is an expansion of recall 2012-338.

Transport CanadaOct 21, 20152015493Model years 2009–2011View details →
Sequoia I · 2000–2007
RecallCriticalInteriorNA

Airbag

On certain vehicles, the passenger (frontal) airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the passenger airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Note: This recall is superseded by recall 2016103. Please see recall 2016103 for more information. <a href="http://wwwapps.tc.gc.ca/Saf-Sec-Sur/7/VRDB-BDRV/search-recherche/detail.aspx?lang=eng&&rn=2016103">Click here for more information</a>

Transport CanadaJun 17, 20152015269Model years 2002–2007View details →
Sequoia I · 2000–2007
RecallCriticalInteriorNA

Airbag

On certain vehicles, the passenger (frontal) airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the passenger airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Note: This recall is superseded by recall 2016103. Please see recall 2016103 for more information. <a href="http://wwwapps.tc.gc.ca/Saf-Sec-Sur/7/VRDB-BDRV/search-recherche/detail.aspx?lang=eng&&rn=2016103">Click here for more information</a>

Transport CanadaMay 13, 20152015197Model years 2003–2004View details →
Sequoia I · 2000–2007
RecallCriticalInteriorNA

Air bags

Toyota Motor Engineering & Manufacturing (Toyota) notified the agency on May 13, 2015, that they are recalling 2005-2007 Lexus SC, Toyota Corolla, Corolla Matrix, Sequoia, and Pontiac Vibe, and 2005-2006 Toyota Tundra vehicles that were originally sold, or ever registered, in Florida, along the Gulf Coast, Puerto Rico, Hawaii, the U.S. Virgin Islands, Guam, Saipan and American Samoa. On June 16, 2015 Toyota expanded the recall to cover an additional 769,055 vehicles, including certain model year 2002-2004 Lexus SC, Toyota Sequoia, 2003-2004 Toyota Corolla Matrix, Toyota Corolla, Pontiac Vibe, and Toyota Tundra vehicles, as well the vehicles covered by the May 13, 2015 notification in the portions of Georgia, Alabama, Louisiana, Mississippi and Texas that were not previously included. The inflators in the front passenger air bags are susceptible to rupture in the event of a crash necessitating the deployment of the front passenger air bag.

NHTSA · United StatesMay 13, 201515V286000Model years 2002–2007View details →
Sequoia I · 2000–2007
RecallCriticalInteriorNA

Air bags

Toyota Motor Engineering & Manufacturing (Toyota) notified the agency on May 13, 2015 that they are recalling certain model year 2004 Sequoia vehicles manufactured August 18, 2003, to August 19, 2004, and 2003-2004 Tundra vehicles manufactured March 18, 2003, to August 25, 2004. On June 16, 2015, Toyota expanded the recall to include an additional 1,270,468 vehicles, including model year 2002-2003 and 2005-2007 Sequoia, 2005-2006 Tundra, 2003-2007 Corolla, 2003-2007 Corolla Matrix, 2003-2007 Pontiac Vibe and 2002-2007 Lexus SC vehicles. This is to address a safety defect in the passenger side frontal air bag inflator which may produce excessive internal pressure causing the inflator to rupture upon deployment of the air bag. This recall addresses both the passenger side frontal air bags that were originally installed in the vehicles, as well as replacement air bags that may have been installed as replacement service parts. A replacement air bag may have been installed, as one example, if a vehicle had been in a crash necessitating the replacement of the passenger side frontal air bag.

NHTSA · United StatesMay 13, 201515V285000Model years 2002–2007View details →
Sequoia I · 2000–2007Sequoia II · 2007–2022
RecallCriticalInteriorNA

Seats:Front assembly:Seat heater/cooler

Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion which may damage the seat heater wiring.

NHTSA · United StatesNov 19, 201414V743000Model years 2005–2011View details →
Sequoia I · 2000–2007
RecallCriticalInteriorNA

Airbag

On certain vehicles, the passenger (frontal) airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the passenger airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Note: This recall is superseded by recall 2016103. Please see recall 2016103 for more information. <a href="http://wwwapps.tc.gc.ca/Saf-Sec-Sur/7/VRDB-BDRV/search-recherche/detail.aspx?lang=eng&&rn=2016103">Click here for more information</a>

Transport CanadaJun 12, 20142014224Model years 2002–2003View details →
Sequoia I · 2000–2007
RecallCriticalInteriorNA

Airbag

On certain vehicles, the passenger (frontal) airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the passenger airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Note: This recall is superseded by recall 2016103. Please see recall 2016103 for more information. <a href="http://wwwapps.tc.gc.ca/Saf-Sec-Sur/7/VRDB-BDRV/search-recherche/detail.aspx?lang=eng&&rn=2016103">Click here for more information</a>

Transport CanadaApr 11, 20132013113Model years 2002–2003View details →
Sequoia II · 2007–2022
RecallCriticalInteriorNA

Seats

Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.

NHTSA · United StatesJan 16, 201313V014000Model years 2010–2012View details →
Sequoia II · 2007–2022
RecallCriticalOtherNA

Visibility:Power window devices and controls

Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.

NHTSA · United StatesOct 10, 201212V491000Model years 2008–2009View details →
Older →

Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).