El vástago de la válvula de control del calefactor no cumple con las especificaciones de material. Las temperaturas altas del refrigerante pueden hacer que el vástago presente fugas.
NHTSA · Estados Unidos6 jun 199494V103000Años modelo 1988–1989Traducido automáticamente · original: inglésVer detalles →
Los vehículos no cumplieron los requisitos de la prueba de impacto lateral con barrera móvil de la FMVSS 301, "integridad del sistema de combustible". La fuga de combustible del depósito de gasolina superó la cantidad máxima permitida de derrame.
NHTSA · Estados Unidos23 nov 199393V192000Años modelo 1990–1994Traducido automáticamente · original: inglésVer detalles →
Note: All 1988-89 excel vehicles sold in canada. The reed valve subassembly contained within the air control valve could fail due to corrosion allowing the hot exhaust gases to flow backward into the plastic secondary air filter case when the vehicle is being driven. These hot gases may melt the secondary air filter case and could result in an engine compartment fire. Correction: Reed valve subassembly will be replaced.
Transport Canada30 dic 19911991176Años modelo 1988–1989Mostrado en inglés original · traducción pendienteVer detalles →
The fuel return tube clip may have been incorrectly installed allowing the fuel return hose to contact either the distributor high tension cable or the e.G.R. Valve. This could, over time, result in wear and eventual leakage at the fuel hose. The fuel leakage could result in an underhood fire. V.I.N. Range s.O.P. To kmhla31j1gu040086
Transport Canada18 abr 19861986044Años modelo 1986Mostrado en inglés original · traducción pendienteVer detalles →
In some vehicles, the manufacturer's protective internal coating of the electronic crank angle sensor does not meet specifications, which can cause an open circuit at high operating temperatures. This can cause the vehicle to stall.
NHTSA · Estados Unidos11 may 199494V090000Años modelo 1994Mostrado en inglés original · traducción pendienteVer detalles →
Las transmisiones manuales pueden bloquearse debido a una lubricación insuficiente de los engranajes en la carcasa de la transmisión. Esto puede provocar que las ruedas motrices se traben y que el vehículo se detenga de forma repentina.
NHTSA · Estados Unidos4 oct 199393V167000Años modelo 1986–1989Traducido automáticamente · original: inglésVer detalles →
Deterioration of the reed valve subassembly may lead to a malfunction within the secondary air supply portion of the emission control system. The screws which attach the reeds to the reed valve subassembly may rust, and if the rusting becomes severe, the screw heads will erode and allow the reeds to separate from the reed valve subassembly. Corrosion may also occur on the reed valve subassembly, deforming the reed seats and preventing the reeds from closing properly. Separation of the reeds from the reed valve subassembly or improper closing of the reeds allow hot exhaust gases to flow backward into the plastic secondary air filter case when the vehicle is being driven. These hot exhaust gases may melt the secondary plastic air filter case.
NHTSA · Estados Unidos31 dic 199191V225000Años modelo 1986–1989Mostrado en inglés original · traducción pendienteVer detalles →
The lock washer located under the nut that secures the front hub to the driveshaft may crack due to improper heat treatment. This could result in wheel bearing freeplay and bearing damage with possible wheel lock-up or brake caliper knockback. Correction: Washer will be replaced note: All units have been corrected.
Transport Canada18 may 19901990072Años modelo 1990Mostrado en inglés original · traducción pendienteVer detalles →
The possibility exists that under certain braking conditions, front brake fade may occur,thus reducing braking effectiveness. Correction: Improved semi-metallic brake pads will be installed.
Transport Canada27 nov 19871987127Años modelo 1986–1987Mostrado en inglés original · traducción pendienteVer detalles →
The cotter pin that retains the brake clevis pin may have been omitted or incorrectly installed. If the cotter pin was omitted or if it were to fall out of the clevis pin,the vehicles' brakes would be subject to failure without warning.
Transport Canada29 mar 19861986033Años modelo 1986Mostrado en inglés original · traducción pendienteVer detalles →
A cotter pin in the brake pedal to brake master cylinder linkage assembly may be missing. This pin acts as a retainer for the brake master cylinder pushrod clevis pin. Consequence of defect: The clevis pin may slide out causing the master cylinder/brake pedal linkage to become disengaged. If this linkage becomes disengaged the service brakes cannot be applied, creating the risk of a crash without prior warning.
NHTSA · Estados Unidos17 mar 198686V043000Años modelo 1986Mostrado en inglés original · traducción pendienteVer detalles →
If cruise control main switch is in the on position when engine is started, system can be affected by a short duration voltage drop caused by optional hi-power (h340) radio.
NHTSA · Estados Unidos19 jun 198989V100000Años modelo 1986–1989Mostrado en inglés original · traducción pendienteVer detalles →
Fuentes: NHTSA (Estados Unidos, dominio público), Transport Canada (Licencia de Gobierno Abierto – Canadá), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso y Safety Gate de la UE (Francia, Licence Ouverte 2.0), MLIT (Japón, Licencia de Datos Públicos 1.0) y MOLIT (Corea del Sur, car.go.kr).