Lectura libre · cuenta gratuita para colaborarSucesor de Anticars (2000)

LexusLexus RC

2014–2025 · 1 generaciones · 2 averías documentadas · 4 mercados
Generaciones
Todas las generacionesRC2014–2025222337

Los boletines técnicos (TSB) son instrucciones de reparación que los fabricantes envían a sus concesionarios sobre problemas conocidos. No son llamadas a revisión de seguridad, pero a menudo confirman una avería.

GravedadTodasLeve
Año del modelo
BoletínLeveMotorNA

Boletín

DL: On December 20, 2022, a settlement of claims for certain low pressure fuel pumps was approved by the federal court. The settlement includes Lexus?s agreement to provide a Customer Support Program for certain 2013-2020 model year (MY) vehicles originally equipped with low pressure fuel pumps repaired under Safety Recall 20LA01 or Special Service Campaign 21LC01. The purpose of this Customer Support Program letter is to help clarify how to administer this coverage in accordance with the settlement.

NHTSA · boletín del fabricante10235219Años modelo 2017Mostrado en inglés original · traducción pendienteVer detalles →
BoletínLeveMotorNA

Boletín

DL: On December 20, 2022, a settlement of claims for certain low pressure fuel pumps was approved by the federal court. The settlement includes Lexus?s agreement to provide a Customer Support Program for certain 2015-2020 model year (MY) vehicles that were not previously involved in a Safety Recall or Special Service Campaign related to the low pressure fuel pump. The purpose of this Customer Support Program letter is to help clarify how to administer this coverage in accordance with the settlement.

NHTSA · boletín del fabricante10235220Años modelo 2015Mostrado en inglés original · traducción pendienteVer detalles →
BoletínLeveMotorNA

Boletín

TSB: Some 2013 ? 2020 model year Lexus vehicles may exhibit a hard start and/or MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs): ?DTC P0171 and/or P0174 (System Too Lean Bank 1/Bank 2) ?DTC P0087 Fuel Rail / System Pressure ? Too Low Techstream data list analysis may reveal positive fuel trims including a no pressure condition verified by a manual fuel pressure gauge. Follow the Repair Procedure in this bulletin to address these conditions.

NHTSA · boletín del fabricante10235215Años modelo 2017Mostrado en inglés original · traducción pendienteVer detalles →
BoletínLeveMotorNA

Boletín

Guía de aplicabilidad de la viscosidad del aceite e intervalo de cambio

NHTSA · boletín del fabricante10205358Años modelo 2014Traducido automáticamente · original: inglésVer detalles →
BoletínLeveMotorNA

Boletín

Guía de aplicabilidad de viscosidad de aceite e intervalo de cambio

NHTSA · boletín del fabricante10205359Años modelo 2014Traducido automáticamente · original: inglésVer detalles →
BoletínLeveMotorNA

Boletín

TT: TMS has discovered the current engine active test ?Control the Injection Mode? is not operating as desired when controlling the direct injectors manually on 2GR-FKS or 8AR-FTS engines. When direct injection is started and then stopped using the active test, current ECU logic does not turn off the direct injectors and can cause DTCs P017200, P017500 and P0160300. In order to avoid this condition, technicians should raise engine RPM when changing from Direct Injection active test to Port Injection active test. Use the recommended procedure below to avoid this concern while testing injection mode of 2GR-FKS or 8AR-FTS equipped vehicles. NOTE: If the active test is used multiple times without using this procedure to raise engine RPM, it may be necessary to reset learning values for fuel trim and Air to Fuel ratio before returning vehicle to customer.

NHTSA · boletín del fabricante10152276Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
BoletínLeveMotorNA

Boletín

"tt: Tms has discovered the current engine active test control the injection mode is not operating as desired when controlling the direct injectors manually on 2gr-fks or 8ar-fts engines. When direct injection is started and then stopped using the active test, current ecu logic does not turn off the direct injectors and can cause dtcs p017200, p017500 and p0160300. In order to avoid this condition, technicians should raise engine rpm when changing from direct injection active test to port injection active test. Use the recommended procedure below to avoid this concern while testing injection mode of 2gr-fks or 8ar-fts equipped vehicles. Note: If the active test is used multiple times without using this procedure to raise engine rpm, it may be necessary to reset learning values for fuel trim and air to fuel ratio before returning vehicle to customer."

NHTSA · boletín del fabricante10093695Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →

Fuentes: NHTSA (Estados Unidos, dominio público), Transport Canada (Licencia de Gobierno Abierto – Canadá), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso y Safety Gate de la UE (Francia, Licence Ouverte 2.0), MLIT (Japón, Licencia de Datos Públicos 1.0) y MOLIT (Corea del Sur, car.go.kr).