Boletín
Algunos clientes pueden experimentar un mensaje de fallo del sistema híbrido en el cuadro de instrumentos y que el motor no arranque, junto con otros numerosos DTC.
Los boletines técnicos (TSB) son instrucciones de reparación que los fabricantes envían a sus concesionarios sobre problemas conocidos. No son llamadas a revisión de seguridad, pero a menudo confirman una avería.
Algunos clientes pueden experimentar un mensaje de fallo del sistema híbrido en el cuadro de instrumentos y que el motor no arranque, junto con otros numerosos DTC.
Some customers may experience the audio sound pausing when the engine restarts after i-stop operation under the following situations. The symptoms are caused by an improper part installation in the audio amplifier. A voltage drop error detection of the power source may be too sensitive.
Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
Customers may report excess wind noise from the vehicle and that noise may be coming from the crossbars. As noted in the crossbar instructions, the crossbars should be removed when not in use to reduce fuel consumption from the increased drag and to reduce wind noise. Let the customer know that the instructions show how to install, remove, and adjust the crossbars.
Some customers may complain about a rattle noise coming from the engine compartment when accelerating or idling. This may be caused by play at the turbocharger wastegate pivot arm creating a rattle-type noise. To eliminate this concern, a wave washer has been added.
A tapping/rattling noise may be noticed from the valve train area. This operating condition can occur on new vehicles which have been delivered to Mazda dealers (due to loading and unloading from transport trucks or customers moving their vehicles in and out of their garages to wash the vehicle, etc.). This condition may also occur if the engine is not allowed to warm up after multiple cold starts.
When servicing SKYACTIV engine vehicles requiring to replace the Oil Galley Plug and Crush Washer, order the required part numbers below. These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.
Algunos clientes pueden quejarse de señales de aceite en los amortiguadores o en los amortiguadores de tipo puntal. En la mayoría de los casos, el aceite presente es normal y se debe al aceite que queda en el vástago durante el proceso normal de barrido del sello del vástago. Siga las pautas de inspección que se indican a continuación para determinar si la condición se debe al proceso normal de barrido o a una falla del sello del vástago.
Algunos clientes pueden quejarse de señales de aceite en los amortiguadores o en los amortiguadores de tipo puntal (struts). En la mayoría de los casos, el aceite presente es normal y se debe al aceite que queda en el vástago durante el proceso normal de barrido del retén del vástago. Siga las pautas de inspección que se indican a continuación para determinar si la condición se debe al proceso normal de barrido o a una falla del retén del vástago.
A tapping/rattling noise may be noticed from the valve train area. This operating condition can occur on new vehicles which have been delivered to Mazda dealers (due to loading and unloading from transport trucks or customers moving their vehicles in and out of their garages to wash the vehicle, etc.). This condition may also occur if the engine is not allowed to warm up after multiple cold starts.
Fuentes: NHTSA (Estados Unidos, dominio público), Transport Canada (Licencia de Gobierno Abierto – Canadá), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso y Safety Gate de la UE (Francia, Licence Ouverte 2.0), MLIT (Japón, Licencia de Datos Públicos 1.0) y MOLIT (Corea del Sur, car.go.kr).