Lectura libre · cuenta gratuita para colaborarSucesor de Anticars (2000)

Mazda 2

2002– · 3 generaciones · 13 averías documentadas · 7 mercados
Generaciones

Los boletines técnicos (TSB) son instrucciones de reparación que los fabricantes envían a sus concesionarios sobre problemas conocidos. No son llamadas a revisión de seguridad, pero a menudo confirman una avería.

Año del modelo
MercadoTodosNA
2 III · 2014–
BoletínModeradoElectrónicaNA

Boletín

Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.

NHTSA · boletín del fabricante10199641Años modelo 2021Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínModeradoElectrónicaNA

Boletín

If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.

NHTSA · boletín del fabricante10185813Años modelo 2017Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Algunos clientes pueden quejarse de cualquiera de los siguientes puntos: 1. La pantalla del centro de infoentretenimiento no muestra el código de autorización (OTP) durante la inscripción del vehículo conectado en la aplicación MyMazda. 2. Funciones remotas inoperativas.

NHTSA · boletín del fabricante11039110Años modelo 2021Traducido automáticamente · original: inglésVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Algunos vehículos pueden presentar la luz de verificación del motor encendida con el DTC P0300:00 (Fallo de encendido aleatorio detectado) almacenado. Esto puede deberse a una detección errónea de un fallo de encendido causada por una lógica de control del PCM inadecuada. Para eliminar esta inquietud, se ha modificado la lógica de control del PCM.

NHTSA · boletín del fabricante11012337Años modelo 2021Traducido automáticamente · original: inglésVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Algunos clientes pueden notar que la luz de carga se enciende mientras conducen. Al inspeccionar, se encuentra almacenado en la memoria el DTC P2502:00 PCM (Mal funcionamiento en el voltaje generado por el generador). Esto puede deberse a una resistencia entre la placa de circuito y la masa. Cuando pasa una corriente eléctrica de alta intensidad, la posición del terminal de masa puede no ser suficientemente firme. Para eliminar esta preocupación, se ha modificado el software de control del convertidor CC-CC. Además, se ha revisado el procedimiento de producción. Se aumentó el par de apriete del terminal de masa y de la placa de circuito.

NHTSA · boletín del fabricante11008418Años modelo 2021Traducido automáticamente · original: inglésVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Some customers may experience a check engine light illumination at idle while stopped with DTC P0300:00 stored, resulting in rough idle conditions. P0300:00: Random misfire detected This concern is caused by improper engine control in the idle range. To eliminate the concern, the PCM control software has been modified.

NHTSA · boletín del fabricante11008417Años modelo 2021Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

BSM Radar aiming cannot be performed after rightside BSM control module rekkplacement

NHTSA · boletín del fabricante10213434Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Some customers may experience the CHECK ENGINE light ON with DTC P0089:00 (Spill valve control solenoid valve control circuit range/performance problem) stored. This is caused by improper control software of the PCM detecting a false error, even with normal fuel pressure operation. To correct this issue, the control software of the PCM has been modified.

NHTSA · boletín del fabricante10190951Años modelo 2021Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Replace the Active Driving Display.

NHTSA · boletín del fabricante10185954Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone. P2096:00 - Air fuel too lean P2097:00 - Air fuel too rich P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern.

NHTSA · boletín del fabricante10180595Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display.

NHTSA · boletín del fabricante10188483Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.

NHTSA · boletín del fabricante10186918Años modelo 2017Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Active driving display opens/closes improperly. Some vehicles may exhibit the active driving display opening/closing improperly as described below: * It does not open or close when the ignition is turned ON or OFF . * The display operation does not fully open/close. * It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the act ive driving display which activates pinching detection. Customer having this concern should have their vehicle repaired using the following repair procedure.

NHTSA · boletín del fabricante10186257Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Some customers may experience the active driving display (auto flip-up type) does not flip up and no DTC is stored. Due to improper assembly, a deformed bracket may cause a loose mesh between internal gears. To correct this issue, the active driving display has been changed.

NHTSA · boletín del fabricante10144332Años modelo 2018Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Replace the Active Driving Display.

NHTSA · boletín del fabricante10125470Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.

NHTSA · boletín del fabricante10105642Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.

NHTSA · boletín del fabricante10101468Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the active driving display. Replace the active driving display.

NHTSA · boletín del fabricante10101464Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.

NHTSA · boletín del fabricante10091601Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the active driving display. Replace the active driving display.

NHTSA · boletín del fabricante10090902Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.

NHTSA · boletín del fabricante10090667Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
2 III · 2014–
BoletínLeveElectrónicaNA

Boletín

Bsm radar aiming cannot be performed after right-side bsm control module replacement. If right-dide bsm control module requres replacement for any repair, also replace left side bsm control module to compelte the radar aiming procedure (it's ok to replace the left bsm alone). If the right-side bsm control module is replaced alone, "automatic configuration" is not performed due to program error in module. Because of this, the required "bsm radar aiming" cannot be performed. "automatic configuration" as well as "bsm radar aiming" can be performed if left-side bsm control module is replaced alone or together with right-side bsm control module.

NHTSA · boletín del fabricante10076685Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
2 II · 2007–2014
BoletínLeveElectrónicaNA

Boletín

Mazda: There is possible excessive condensation or water inside the headlamp unit on many mazda models. *rm

NHTSA · boletín del fabricante10037949Años modelo 2011Mostrado en inglés original · traducción pendienteVer detalles →
2 II · 2007–2014
BoletínLeveElectrónicaNA

Boletín

Mazda: There is condensation and fog in the front and rear combination lights. *rm

NHTSA · boletín del fabricante10037655Años modelo 2011Mostrado en inglés original · traducción pendienteVer detalles →

Fuentes: NHTSA (Estados Unidos, dominio público), Transport Canada (Licencia de Gobierno Abierto – Canadá), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso y Safety Gate de la UE (Francia, Licence Ouverte 2.0), MLIT (Japón, Licencia de Datos Públicos 1.0) y MOLIT (Corea del Sur, car.go.kr).