Lecture libre · compte gratuit pour contribuerSuccesseur d’Anticars (2000)

GMCGMC Envoy

1998–2009 · 2 générations · 27 défauts documentés · 1 marchés
Générations

Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.

Année modèle
MarchéTousNA
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

Cette communication d’information préliminaire fournit au technicien des informations sur les véhicules présentant un problème intermittent de ne pas tourner à manivelle, pas de démarrage ou de démarrage avec le voyant de sécurité allumé. Le technicien peut trouver les codes de diagnostic B3055, B3

NHTSA · bulletin constructeur11039894Années modèle 2007Traduit automatiquement · original : anglaisVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

Cette communication d’information préliminaire fournit au technicien des informations sur les véhicules présentant un problème intermittent de ne pas tourner à manivelle, pas de démarrage ou de démarrage avec le voyant de sécurité allumé. Le technicien peut trouver les codes de diagnostic B3055, B3060, B3935, C0750, C0755, C0760, C0765 et/ou C0775.

NHTSA · bulletin constructeur11021792Années modèle 2007Traduit automatiquement · original : anglaisVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

NHTSA · bulletin constructeur10232136Années modèle 2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

NHTSA · bulletin constructeur10219266Années modèle 2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

NHTSA · bulletin constructeur10200151Années modèle 2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

NHTSA · bulletin constructeur10114954Années modèle 2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

NHTSA · bulletin constructeur10114746Années modèle 2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · bulletin constructeur10114354Années modèle 2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

10054E - Special Coverage (customer co-pay discontinued). The contacts on the fuel level sensor may wear prematurely. This wear could cause the fuel gauge to read empty after filling the tank and cause the malfunction indicator light (MIL) to illuminate. As the fuel level in the tank drops, the MIL may turn off and the gauge may display a reading; however, the reading may indicate a slightly higher level of fuel than what is in the tank. Eventually, as the contacts continue to wear, the fuel gauge will stop working and the MIL will illuminate continuously. If the condition occurs within the stated terms, dealers will install a new design fuel level sensor.

NHTSA · bulletin constructeur10114183Années modèle 2005–2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.

NHTSA · bulletin constructeur10113418Années modèle 2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

NHTSA · bulletin constructeur10113177Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · bulletin constructeur10113120Années modèle 2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

NHTSA · bulletin constructeur10112697Années modèle 2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · bulletin constructeur10112436Années modèle 2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

NHTSA · bulletin constructeur10111927Années modèle 2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

NHTSA · bulletin constructeur10111737Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

Diagnostic information on engine oil leak from rear of crankshaft. *tt 05-06-01*022 supplement - crankshaft oil leak repair instrumentions. *tt

NHTSA · bulletin constructeur10017385Années modèle 2005Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

Service engine soon light due a diagnostic trouble code p0606 diagnostic trouble code, operate in reduced engine power mode, and potentially stall. *tt

NHTSA · bulletin constructeur10017230Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinModéréÉlectroniqueNA

Bulletin

Concerns with no start, turn/hazard, interior lamps, driver information center (dic), radio, theft alarm, wipers, cruise, shift interlock, horn and/or key in signal inoperative. *tt

NHTSA · bulletin constructeur628833Années modèle 2002Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinMineurÉlectroniqueNA

Bulletin

Ce bulletin de service fournit des informations sur certains véhicules qui peuvent basculer ou se déplacer légèrement vers l'avant ou vers l'arrière lorsqu'ils sont en position P (Park) au démarrage après un long séjour à froid. Ce phénomène peut s'accompagner d'un bruit de claquement. Il s'agit d'un mouvement léger, qui se remarque plus souvent visuellement que physiquement, lorsqu'on observe le véhicule de l'extérieur et que l'on utilise la fonction de démarrage automatique, si le véhicule en est équipé.

NHTSA · bulletin constructeur11009088Années modèle 2007Traduit automatiquement · original : anglaisVoir le détail →
Envoy II · 2002–2009
BulletinMineurÉlectroniqueNA

Bulletin

Vehicle Wide Programming (VWP) est un nouveau processus de mise à jour des logiciels sur les véhicules GM. Il permet, par une seule sélection dans Techline Connect, d'identifier d'abord les modules qui nécessitent une mise à jour, puis de procéder à la mise à jour des modules concernés (à quelques exceptions près). La mise à jour des modules s'effectue en parallèle, au lieu que le technicien ait à mettre à jour un module à la fois. Cela permet une approche plus rationalisée pour les concessionnaires et les clients.

NHTSA · bulletin constructeur11006621Années modèle 2006Traduit automatiquement · original : anglaisVoir le détail →
Envoy II · 2002–2009
BulletinMineurÉlectroniqueNA

Bulletin

Ce bulletin fournit des informations sur les réparations de mise à la masse électrique à l'aide de nouvelles fixations de remplacement General Motors à finition conductrice.

NHTSA · bulletin constructeur10252735Années modèle 2006Traduit automatiquement · original : anglaisVoir le détail →
Envoy II · 2002–2009
BulletinMineurÉlectroniqueNA

Bulletin

This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.

NHTSA · bulletin constructeur10249011Années modèle 2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinMineurÉlectroniqueNA

Bulletin

Programming And Activation Of Replacement OnStar Modules.

NHTSA · bulletin constructeur10246951Années modèle 2006Affiché en anglais d’origine · traduction en attenteVoir le détail →
Envoy II · 2002–2009
BulletinMineurÉlectroniqueNA

Bulletin

This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

NHTSA · bulletin constructeur10237387Années modèle 2007Affiché en anglais d’origine · traduction en attenteVoir le détail →
Plus anciens →

Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).