Lecture libre · compte gratuit pour contribuerSuccesseur d’Anticars (2000)

Mazda 3

2003– · 4 générations · 63 défauts documentés · 8 marchés
Générations

Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.

Année modèle
MarchéTousNA
3 IV · 2019–
BulletinModéréÉlectroniqueNA

Bulletin

Some customers may experience the check engine light on with DTC P0126:00 (Thermostat stuck open) stored. This is due to improper PCM logic control. To eliminate the concern, the PCM control software has been modified. REPAIR PROCEDURE 1. Verify the customer concern. 2. Reprogram the ECU with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). Refer to MDARS ECU Reprogramming Procedure. NOTE: Be sure to submit Diagnostic Information (ODR) data as it is a required item and will be checked during warranty claim submission. Instructions can be found under M-MDS -> MDARS (Uploading Diagnostic Information (ODR) Data). 3. Clear any other DTCs. 4. Verify the repair by starting the engine (READY ON) and confirming there is no CHECK ENGINE light ON or abnormal warning lights present.

NHTSA · bulletin constructeur11030600Années modèle 2026Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 IV · 2019–
BulletinModéréÉlectroniqueNA

Bulletin

Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. NOTE: SA-045/21 HAS BEEN SUPERCEDED TO SSPC7.

NHTSA · bulletin constructeur10200938Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 IV · 2019–
BulletinModéréÉlectroniqueNA

Bulletin

Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built March 20, 2021 and later.

NHTSA · bulletin constructeur10200937Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 IV · 2019–
BulletinModéréÉlectroniqueNA

Bulletin

Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later.

NHTSA · bulletin constructeur10200935Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 IV · 2019–
BulletinModéréÉlectroniqueNA

Bulletin

Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later.

NHTSA · bulletin constructeur10200934Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 IV · 2019–
BulletinModéréÉlectroniqueNA

Bulletin

Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later. Engine no start due to low battery voltage.

NHTSA · bulletin constructeur10199636Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 III · 2013–2018
BulletinModéréÉlectroniqueNA

Bulletin

If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.

NHTSA · bulletin constructeur10185813Années modèle 2017Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 IV · 2019–
BulletinModéréÉlectroniqueNA

Bulletin

Some vehicles may exhibit DTC B14F0:76 [VCM] (Forward sensing camera (FSC) deviation) stored in memory and the i-ACTIVSENSE warning light (amber) on after BCM replacement. This is caused by the learning value of the forward sensing camera (FSC) aiming being initialized after BCM replacement due to a software malfunction of the FSC. To correct this concern, the FSC software will be modified to not initialize the value of the FSC aiming after BCM replacement.

NHTSA · bulletin constructeur10166849Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 IV · 2019–
BulletinModéréÉlectroniqueNA

Bulletin

If a customer comes in with the following concerns, contact Hotline for assistance. OIL PRESSURE WARNING light and/or the CHECK ENGINE light ON, DTC P055F and/or P0524 stored, No drivability concern or engine mechanical noise, Outside the VIN range in TSB 01-020/18.

NHTSA · bulletin constructeur10165353Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 IV · 2019–
BulletinModéréÉlectroniqueNA

Bulletin

Some vehicles may exhibit DTC U2120:00 and/or U2500:82 stored in memory and the i-ACTIVSENSE warning light (amber) ON when turning ON the ignition after any electronic control unit (ECU) is reprogramed or configured using MDARS. NOTE: ECU stands for general units (cameras and modules), all of which can be reprogrammed. This is caused by a software malfunction of the forward sensing camera (FSC). To correct this issue, the FSC software will be modified.

NHTSA · bulletin constructeur10164075Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 IV · 2019–
BulletinModéréÉlectroniqueNA

Bulletin

Some vehicles may exhibit DTC B14F0:76 [VCM] stored in memory and the i-ACTIVSENSE warning light (amber) on after BCM replacement. DTC B14F0:76 [VCM]: Forward sensing camera (FSC) deviation (iACTIVSENSE warning light (amber)). This is caused by the learning value of the forward sensing camera (FSC) aiming being initialized after BCM replacement due to a software malfunction of the FSC. To correct this concern, the FSC software will be modified to not initialize the value of the FSC aiming after BCM replacement.

NHTSA · bulletin constructeur10163828Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 IV · 2019–
BulletinModéréÉlectroniqueNA

Bulletin

SiriusXM Traffic Plus and Travel Link are displayed with Mazda in-vehicle factory navigation systems. Both of these services provide information in the U.S. & Canada. NOTE: SiriusXM Traffic Plus and Travel Link subscription is free of charge for 3 years only if equipped with factory installed navigation system. NOTE: 2019 Mazda3 is not equipped with factory installed navigation system, however, it is available as a dealer installed accessory. SiriusXM Traffic Plus and Travel Link are available on the 2019 Mazda3 Preferred Package and above, as a paid subscription. Traffic Plus feature requires in-vehicle navigation SD card. SiriusXM Satellite Radio trial subscription is free of charge for 3 months.

NHTSA · bulletin constructeur10154458Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 III · 2013–2018
BulletinModéréÉlectroniqueNA

Bulletin

Some customer may complain about the CHECK ENGINE light ON while driving. When diagnosed, it is found that the PCM has stored DTC P0456 for evaporative gas leakage (extremely low). This may be caused by leakage detected from the catch tank unit (1) at the purge valve (2).

NHTSA · bulletin constructeur10143956Années modèle 2017Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 III · 2013–2018
BulletinModéréÉlectroniqueNA

Bulletin

Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found." After the user selects OK, the system finds the address or a nearby address.Instead of finding the correct address number the system adds a digit to the end of the number. Example: You enter 151 and the system comes back with 1510, 1511, 1515, 1516, etc. This only occurs with MAZDA CONNECT software version 59.00.532 or 59.00.540, which started being installed into vehicles in January 2018. The concern can be eliminated by installing MAZDA CONNECT software version 59.00.545 now available on MGSS.

NHTSA · bulletin constructeur10136765Années modèle 2018Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 III · 2013–2018
BulletinModéréÉlectroniqueNA

Bulletin

Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found." After the user selects OK, the system finds the address or a nearby address.Instead of finding the correct address number the system adds a digit to the end of the number. Example: You enter 151 and the system comes back with 1510, 1511, 1515, 1516, etc.This only occurs with MAZDA CONNECT software version 59.00.540, which started being installed into vehicles in January 2018. The concern can be eliminated by installing MAZDA CONNECT software version 59.00.504.

NHTSA · bulletin constructeur10134940Années modèle 2018Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 III · 2013–2018
BulletinModéréÉlectroniqueNA

Bulletin

An updated version of the software for the Connectivity Master Unit (CMU) has become available. Under this MSP41, the CMU of applicable Mazda3 vehicles will be reprogrammed to the updated version using a USB memory stick. This software update includes some fixes for the Infotainment System as described below as well as some additional minor fixes. *A "Charging System Malfunction" message may be displayed on the center display by mistake (no charging system warning light in the instrument cluster). *The Voice Recognition may not activate even when pressing the TALK button. *The warning of "Check XM Antenna" may be continuously displayed on the center display.

NHTSA · bulletin constructeur10110987Années modèle 2014Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 III · 2013–2018
BulletinModéréÉlectroniqueNA

Bulletin

An updated version of the software for the Connectivity Master Unit (CMU) has become available. Under this MSP41, the CMU of applicable Mazda3 vehicles will be reprogrammed to the updated version using a USB memory stick. This software update includes some fixes for the Infotainment System as described below as well as some additional minor fixes.?A ?Charging System Malfunction? message may be displayed on the center display by mistake (no charging system warning light in the instrument cluster).?The Voice Recognition may not activate even when pressing the TALK button.?The warning of ?Check XM Antenna? may be continuously displayed on the center display.

NHTSA · bulletin constructeur10110989Années modèle 2014Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 II · 2008–2013
BulletinModéréÉlectroniqueNA

Bulletin

Some customers may complain about one or more of the following concerns. 1. Sms/text cannot be downloaded when onnected via bluetooth. 2. Operational concerns when playing a media device (ipod, usb stick etc.) connected via the usb port. A. After the ignition is turned on, it takes a long time to load all the data from the device before starting playback. Depending on the data volume, it can take up to several minutes. B. After the ignition is turned on, the playback always starts from the first track. It does not start from the last playing track/position when the ignition was turned off. C. Ipod error message for the apple ios 8.0 or higher software on iphone 4, 5, or 6. These concerns may be caused by the software of the bluetooth/hands-free module that controls the usb connection. To improve these concerns, the software of the bluetooth/hands-free module has been changed. Note: The updated software of the bluetooth/hands-free module will only address sms/text concerns for the apple iphone at this time.

NHTSA · bulletin constructeur10105462Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 II · 2008–2013
BulletinModéréÉlectroniqueNA

Bulletin

Some customers may complain about one or more of the following concerns. 1. Sms/text cannot be downloaded when connected via bluetooth. 2. Operational concerns when playing a media device (ipod, usb stick etc.) connected via the usb port. A. After the ignition is turned on, it takes a long time to load all the data from the device before starting playback. Depending on the data volume, it can take up to several minutes. B. After the ignition is turned on, the playback always starts from the first track. It does not start from the last playing track/position when the ignition was turned off. These concern may be caused by the software of the bluetooth/hands-free module that controls the usb connection. To improve these concerns, the software of the bluetooth/hands-free module has been changed. Note: The updated software of the bluetooth/hands-free module will only address sms/text concerns for the apple iphone at this time.

NHTSA · bulletin constructeur10100714Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 II · 2008–2013
BulletinModéréÉlectroniqueNA

Bulletin

Some customers may complain about one or more of the following concerns. 1. Sms/text cannot be downloaded when connected via bluetooth. 2. Operational concerns when playing a media device (ipod, usb stick etc.) connected via the usb port. A. After the ignition is turned on, it takes a long time to load all the data from the device before starting playback. Depending on the data volume, it can take up to several minutes. B. After the ignition is turned on, the playback always starts from the first track. It does not start from the last playing track/position when the ignition was turned off. These concern may be caused by the software of the bluetooth/hands-free module that controls the usb connection. To improve these concerns, the software of the bluetooth/hands-free module has been changed. Note: The updated software of the bluetooth/hands-free module will only address sms/text concerns for the apple iphone at this time. The updated software of the bluetooth/handsfree module will not address the ipod error message concern for the apple ios 8.0 or higher software on iphone 4, 5, or 6 at this time.

NHTSA · bulletin constructeur10099690Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 II · 2008–2013
BulletinModéréÉlectroniqueNA

Bulletin

Some customers may complain about one or more of the following concerns. 1. Sms/text cannot be downloaded when connected via bluetooth. 2. Operational concerns when playing a media device (ipod, usb stick etc.) connected via the usb port. A. After the ignition is turned on, it takes a long time to load all the data from the device efore starting playback. Depending on the data volume, it can take up to several minutes. B. After the ignition is turned on, the playback always starts from the first track. It does not start from the last playing track/position when the ignition was turned off. C. Ipod error message for the apple ios 8.0 or higher software on iphone 4, 5, or 6. These concerns may be caused by the software of the bluetooth/hands-free module that controls the usb connection. To improve these concerns, the software of the bluetooth/hands-free module has been changed. Note: The updated software of the bluetooth/hands-free module will only address sms/text concerns for the apple iphone at this time.

NHTSA · bulletin constructeur10099686Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 III · 2013–2018
BulletinModéréÉlectroniqueNA

Bulletin

Some customers may experience the following symptom:A.Warning message i-eloop malfunction (mazda3) or i-eloop inspection required (mazda6) is dis-played in the instrument cluster information display while driving.B.The master warning light and charging system warning light illuminate. C.Dtc p1794:00 (capacitor (i-eloop) system: Capacitor (i-eloop) malfunction) is stored in pcm memory.

NHTSA · bulletin constructeur10098382Années modèle 2014Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 III · 2013–2018
BulletinModéréÉlectroniqueNA

Bulletin

Some customers may experience one of the following two symptoms:1. Symptom (mazda6 only)a.Warning message i-eloop inspection required is displayed in the instrument cluster information display while driving.B.The master warning light will be illuminated. C.Dtc p1794:00 (capacitor (i-eloop) system: Capacitor (i-eloop) malfunction) will be stored in pcm mem-ory.

NHTSA · bulletin constructeur10098145Années modèle 2014Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 III · 2013–2018
BulletinModéréÉlectroniqueNA

Bulletin

Some customers may experience one of the following two symptoms: 1. Symptom (mazda6 only) a. Warning message i-eloop inspection required is displayed in the instrument cluster information display while driving. B. The master warning light will be illuminated.C. Dtc p1794:00 (capacitor (i-eloop) system: Capacitor (i-eloop) malfunction) will be stored in pcm memory.

NHTSA · bulletin constructeur10098016Années modèle 2014Affiché en anglais d’origine · traduction en attenteVoir le détail →
3 III · 2013–2018
BulletinModéréÉlectroniqueNA

Bulletin

Some customers may experience one of the following two symptoms: 1. Symptom (mazda6 only) a. Warning message i-eloop inspection required is displayed in the instrument cluster information display while driving. B. The master warning light will be illuminated. C. Dtc p1794:00 (capacitor (i-eloop) system: Capacitor (i-eloop) malfunction) will be stored in pcm memory.2. Symptom (mazda3 and mazda6) a. Warning message battery management system inspection required and then "charging system malfunction/engine could stop unexpectedly is displayed in the instrument cluster information display after driving in the rain. B. The master warning light will be illuminated. The mazda6 warning indicator light and warning messages are shown below: C. The following dtcs are stored in pcm memory: Dtc p1794:00 - capacitor (i-eloop) system: Capacitor (i-eloop) malfunction dtc p2502:00 - generator system: Malfunction in voltage generated by generator

NHTSA · bulletin constructeur10098002Années modèle 2014Affiché en anglais d’origine · traduction en attenteVoir le détail →
Plus anciens →

Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).