Lettura libera · account gratuito per contribuireErede di Anticars (2000)

Audi 80 B2 (81)

1978–1986 · 3 difetti documentati · 2 mercati
Anno modello
MercatoTuttiNA
RichiamoCriticoCarrozzeriaNA

Richiamo

In the rear trunk area, the right rear side member for the mounting buffer may not have been welded according to specifications. In the event of an accident resulting in rear end damage it is possible that the right rear side member could break loose, damaging the fuel tank and causing fuel leakage.

Transport Canada27 mar 19811981039Anni modello 1980–1981Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoCriticoFreniNA

Richiamo

The interior surface of the threaded hole for the front brake caliper brake hoses may contain porous spots which would allow brake fluid to seep out of the calipers during heavy brake applications. Prolonged seepage will eventually reeduce brake fluid level in the reservoir and may lead to complete brake failure.

Transport Canada12 nov 19801980148Anni modello 1981Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoCambioNA

Powertrain

On vehicles with automatic transmission, a low oil level in the differential could cause premature bearing and gear wear and eventual failure of the differential. This could result in possible drive wheel lock-up and loss of vehicle control. Correction: Differential will be drained and oil will be replaced with an advanced design high performance gear oil. Owners will be provided with a revised maintenance schedule.

Transport Canada22 gen 19931993008Anni modello 1985–1987Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoCambioNA

Power train:Axle assembly

The differential oil of the transaxle is lost over time due to evaporation. Low oil levels cause premature bearing and gear wear and eventual failure of the differential.

NHTSA · Stati Uniti11 gen 199393V006000Anni modello 1985–1987Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Engine

On vehicles with automatic transmission, the idle stabilizer valve may experience excessive wear. Such wear causes idle fluctuations which are barely noticeable at first, but ultimately could result in unsatisfactory driveability. Correction: Idle stabilizer valve will be replaced. V.I.N. Range wau***8**fa000001 to wau***8**ga138778

Transport Canada26 mag 19871987054Anni modello 1985–1986Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoAltroNA

Vehicle speed control

Excessive wear of idle stabilizer could cause idle fluctuations.

NHTSA · Stati Uniti18 mag 198787V069000Anni modello 1985–1986Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoAbitacoloNA

Seats And Restraints

The seat belt buckles manufactured by afg and located on the rear seat of the audi 4000 and the right front seat of the audi 5000 may not lock securely, although the metal tongue of the seat belt has been fully engaged. In the event of an abrupt brake application or on impact, these buckles could become unlocked. Correction: Vehicles will be inspected and all seat belt buckles manufactured by afg will be replaced. V.I.N. Range audi 4000 - wau***8*ga*124887 to wau***8*ga*137554 audi 5000 - wau**44*g**087473 to wau**44*g**099448

Transport Canada4 set 19861986098Anni modello 1986Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoAbitacoloNA

Seat belts:Front:Buckle assembly

Rear or front right seat belt locks may not properly engage. Consequence of defect: Seat belts could separate in event of heavy brake application or impact and thus subject passengers to injury.

NHTSA · Stati Uniti18 ago 198686V113000Anni modello 1986Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Fuel system, gasoline:Fuel injection system

The fuel pump may stop functioning without warning. This can occur because an electrical connector in the fuse panel may overheat and interrupt the electrical circuit.

NHTSA · Stati Uniti9 nov 198383V117000Anni modello 1980–1981Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoCarrozzeriaNA

Structure:Frame and members

Rear bumper system on certain vehicles may not have been properly welded during assembly. In the event of a rear end collision, the right side bumper supportor could break loose, damage the fuel tank and allow fuel to leak.

NHTSA · Stati Uniti24 mar 198181V039000Anni modello 1980–1981Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoFreniNA

Service brakes, hydraulic:Foundation components:Disc:Caliper

On certain vehicles, porous spots may have developed on the interior surface of the threaded hole for the brake hose during the moulding process. These spots allow brake fluid to seep from the calipers during heavy brake applications.

NHTSA · Stati Uniti12 nov 198080V146000Anni modello 1981Mostrato in inglese originale · traduzione in attesaVedi dettagli →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).